Related Manuals for SmartLab walk
Summary of Contents for SmartLab walk
- Page 1 3-D Step-counter User Manual Please read this user manual thoroughly before first using this device HMM Diagnostics GmbH D-69221 Dossenheim, Germany www.hmm.info...
-
Page 3: Table Of Contents
Content I. Introduction II. Your smartLAB ® walk Display & functions Specifications III. Setup & Functions Inserting the battery Mounting the carrying cord Before the first use: Setting weight, step length, signal tone und time: Starting up Memory function Additional functions... -
Page 4: Introduction
You can comfortably put it in your pocket and it will count all your movements. smartLAB ® walk helps you finding your own individual training level and thus, enables you to control and enhance progress in your personal fitness workout. -
Page 5: Your Smartlab Walk
II. Your smartLAB ® walk Display & functions Select Settings, Change Settings Key Lock Symbol Mute Symbol On/Off, Select Menu, Clock Display Steps walked steps Specifications Name: smartLAB ® walk Size: 70 x 37 x 8,5 mm Weight: 24 g... -
Page 6: Setup & Functions
III. Setup & Functions Inserting the battery In order to change/ insert the battery, you need to unscrew the battery lid on the back of the device. Place the coin cell with the plus side to top into the opening. If you change the battery, use the screwdriver to lever off the battery. -
Page 7: Mounting The Carrying Cord
Mounting the carrying cord You can wear your smartLAB ® walk with the carrying cord included in the set. To do so, you will have to connect the cord to the device by doing the following steps: Push the thin end of the cord through the two tiny eyes at the back side of the device. -
Page 8: Before The First Use
Before the first use: Before first using your smartLAB ® walk step counter, please hold the „Disp/ Set“ button pressed for more than 3 seconds. The device will enter the setting mode. Setting weight, step length, signal tone und time: Setting weight: 1. - Page 9 After having set your personal weight, press „Disp/ Set“ to confirm. Setting step length: After you entered your body weight, step length symbol flashes. Now you can enter your step length by pressing the “M/” button. The step length can vary between 30 and 120 cm. After having set your correct step length, confirm with „Disp/ Set“.
- Page 10 „Disp/ Set“ button. Note: Setting your weight and step length is essential for the display of walked distances and burned calories. You need to enter correct values for both parameters. Otherwise it is impossible for smartLAB walk to display ®...
-
Page 11: Starting Up
• After having set time and step length, you can use your smartLAB ® walk step counter. Just take the device and start walking. The device will turn on automatically when it registeres a movement. The display will read “HELLO”... -
Page 12: Additional Functions
Please exchange the batteries. ® Step counter and batteries need to be disposed of according to local regulations. Locking your device: If no button is pushed for 30 seconds, your smartLAB walk automatically ®... -
Page 13: Maintenance
When you are in user mode, your device automatically turns off after 2 minutes of non-use. When your smartLAB ® walk is picked up and used again, the display will read „HELLO“. Maintenance • Do not dump the device or use force while operating it •... -
Page 14: Warranty
Warranty HMM Diagnostics GmbH products need to fulfill high quality requirements. Because of this reason, HMM Diagnostics GmbH gives a 2-year warranty by purchasing this smartLAB product. You can even extend the warranty from ® 2 to 5 years without extra pay when you register your product. Please use the warranty card included in your product set. - Page 15 Manufacturer: HMM Diagnostics GmbH Friedrichstr. 89 D-69221 Dossenheim, Germany mail: info@hmm.info www.hmm.info Weitere Informationen zu den smartLAB Produkten / ® More information on our smartLAB products: ® www.smartlab.org...
Need help?
Do you have a question about the walk and is the answer not in the manual?
Questions and answers