Korg KARMA 2 Update Manual page 20

A EG A (Amp EG Attack Time)
A EG D (Amp EG Decay Time)
A EG S (Amp EG Sustain Level)
A EG R (Amp EG Release Time)
These adjust only the amp parameter as in "F.A EG A,"
"F.A EG D," "F.A EG S," or "F.A EG R" respectively.
LFO1 Sp (LFO1 Speed)
Adjusts the LFO1 speed of program OSC 1/2. The param-
eter will be controlled in the same way as when CC#76 is
received. (☞PG p.244, Bank F: p.273)
PLFO1 I. (Pitch LFO1 Intensity) [-12.00...+00.00...+12.00]
Adjusts the program OSC 1/2 pitch LFO1 intensity (the
depth of pitch modulation produced by LFO1). The
parameter will be controlled in the same way as when
CC#77 is received. (☞PG p.244, Bank F: p.274)
For bank F programs, this parameter has a range of -
99...+00...+99, unlike other programs. Your setting of -
12.00...+00.00...+12.00 will be valid, but due to the
difference in resolution, the pitch may not be precisely
as you specify.
LFO1 Fd (LFO1 Fade)
Adjusts the program OSC 1/2 LFO1 "Fade" parameter (the
time from when the LFO begins to take effect until it
reaches the maximum level; 5.3-1a ☞PG p.24).
For bank F programs, this controls the "LFO 1/2, 3, 4
Fade." This will correspond to the LFO 1–4 that is
selected in Pitch AMS1, AMS2 (PROG 3.1: Ed-Pitch,
OSC1/2 page) or Common Pitch Mod. AMS (PROG
3.1: Ed-Pitch, Common page).
LFO1 Dl (LFO1 Delay)
Adjusts the program OSC 1/2 pitch LFO1 delay (the time
from note-on until the LFO begins to take effect). The
parameter will be controlled in the same way as when
CC#78 is received. (☞PG p.244, Bank F: p.274)
P.Strch (Pitch Stretch)
Simultaneously adjusts the program OSC 1/2 Transpose
and Tune parameters. This lets you create a rich variety of
tonal changes without impairing the character of the
original sound. This controls the same parameters as
Performance Editor - "Stretch (Pitch Stretch)" (1.1-2b).
(☞PG p.4)
This has no effect on bank F programs.
Dtune 1(Detune 1)
Adjusts the tuning of program OSC 1. This controls the
OSC1 Multisample "Tune" parameter (2.1-2c ☞PG p.9).
For bank F programs, this controls the OSC "Trans
(Transpose)" and "Tune" parameters (☞PG p.276).
Dtune 2 (Detune 2)
Adjusts the tuning of program OSC 2. This controls the
OSC2 Multisample "Tune" parameter (2.1-2c ☞PG p.9).
For bank F programs, this controls the OSC "Trans
(Transpose)" and "Tune" parameters (☞PG p.276).
This is valid only if the program's "Oscillator Mode"
(2.1-1a ☞PG p.7) is set to Double.
[-99...+00...+99] Hold
[-99...+00...+99]
Controls the program's Voice Assign - "Hold" parameter
(2.1-1b ☞PG p.7). If you turn this Off, the OSC1/2 Amp EG
[-99...+00...+99]
[-99...+00...+99] Release Time parameter will be set to 0 in order to make
full use of the effect.
[-199...+00...+199]
Normally you can make effective use of this with a drum
program. When you turn this Off, the key-off timing will
be valid, letting you use the key-on/off timing to control
the gate time. Sometimes you can obtain an interesting
effect by turning this Off for a previously-created drum
track.
Reverse
Controls the "Rev (Reverse)" parameter (2.1-1b ☞PG p.9,
5.1-1b ☞PG p.143) for each Multisample or Drumsample of
program OSC1/2. If you turn this On, all multisamples and
drum samples will play backward. If you turn this Off, all
multisamples and drum samples will play normally. If you
set this to PRG, the settings of the program (or the drum
kit used by the program) will be used. Normally you can
make effective use of this with a drum program.
[-99...+00...+99]
5.3–1b: UTILITY
[-99...+00...+99]
"Memory Status", "Solo Sel. Track", "Rename Song",
"Delete Song", "Copy From Song" (☞PG p.71)
"Copy From Comb" (☞PG p.72, ☞p.20)
"Load Template" (☞PG p.72)
"Save Template", "FF/REW Speed", "Set Location" (☞PG p.73)
"Copy From Prog" (☞p.20)
[-12...+00...+12]
[-1200...+0000...+1200]
[-1200...+0000...+1200]
For bank F programs, the EG Release Time parameter
used by the Amp will be set to 0.
This has no effect on bank F programs.
[Off, On]
[Off, PRG, ON]
19