Clarke EZ-8 Operator's Manual
  1. Manuals
  2. Brands
  3. Clarke Manuals
  4. Floor Machine
  5. EZ-8
  6. Operator's manual

Clarke EZ-8 Operator's Manual

Hide thumbs Also See for EZ-8:

Advertisement

Table of Contents

See also: Operator's Manual
Division of
EZ-8
Operator's
Manual
Sander
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
American Sanders machine could result in injury to you or to other personnel; damage to the machine
or to other property could occur as well. You must have training in the operation of this machine
before using it. If your operator(s) cannot read this manual, have it explained fully before attempting
to operate this machine.
Si Ud. o sus operadores no pueden leer el Inglés, se hagan explicar este manual completamente
antes de tratar el manejo o servicio de esta máquina.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: Clarke
, 2100 Highway 265, Springdale, Arkansas 72764
®
Form No. 78425C
7/03
Printed in the U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Clarke EZ-8

Summary of Contents for Clarke EZ-8

  • Page 1 This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.

  • Page 2: Table Of Contents

    Section II Parts and Service Manual Assembly Drawing #1 ..............14 Assembly Parts List #1 .............. 15 Assembly Drawing #2 ..............16 Assembly Parts List #2 .............. 17 Wiring Diagram ................18 Page 2 American Sanders EZ - 8 Sander Operator's Manual Clarke ®...

  • Page 3: Operator Safety Instructions

    Failure to read the Owner's Manual prior to operating or attempting any service or mainte- nance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
  • Page 4 Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs performed by unauthorized personnel will void your warranty. Servicing of this unit must always be referred to an authorized Clarke American Sanders distributor. CAUTION: Use of this machine to move other objects or to climb on could result in injury or damage.

  • Page 5: Introduction And Machine Specifications

    Your equipment may be inappropriate on some installations. Always consult with the flooring manufacturer on the proper installation, preparation, and finishing of their product. Determine suitability of your equipment in preparing the product. American Sanders EZ - 8 Sander Operator's Manual Page 5 Clarke ®...

  • Page 6: How To Transport The Machine

    Figure # 2 7. Secure chassis to prevent movement in cargo area. Place handle and dust pipe in cargo area. Figure # 4 Figure # 3 Page 6 American Sanders EZ - 8 Sander Operator's Manual Clarke ®...

  • Page 7: Machine Set-Up

    (power supply). Press the selector switch to the start (S) position. Once started, Figure # 8 allow switch to return to run (R) position. American Sanders EZ - 8 Sander Operator's Manual Page 7 Clarke ®...
  • Page 8 Sanding dust can spontaneously ignite and cause a fire or explosion. Empty dust into a metal container clear of any combustible mate- rial. Page 8 American Sanders EZ - 8 Sander Operator's Manual Clarke ®...

  • Page 9: Sanding Cuts And Sandpaper

    For final sanding of certain hardwoods. For clean-up of initial cuts (50 grit). 100 grit For final sanding of certain hardwoods and 945400/25 945937/10 945422/10 conifers where a smooth surface is desired. American Sanders EZ - 8 Sander Operator's Manual Page 9 Clarke ®...

  • Page 10: Sander Adjustment Procedures

    3. Loosen the leveling screw (relax the leveling spring) to sand heavier on the side opposite the drive belts. Page 10 American Sanders EZ - 8 Sander Operator's Manual Clarke ®...

  • Page 11: Routine Maintenance

    NLGI grade 2, -30 F to 250 58-75 SUS at 210 grease lubricant. Motor shaft after 1 5000 hrs. Fan shaft After first 1500 hrs. American Sanders EZ - 8 Sander Operator's Manual Page 11 Clarke ®...

  • Page 12: Troubleshooting

    Damage and/or worn bearing. Remove drive belts, rotate arbor noise coming from machine. motor and fan shafts to locate dragging or rough bearing. Contact an authorized Clarke American Sanders dealer. Dust pick-up is poor. Dust bag is over full. Empty contents of bag.

  • Page 13: Section Ii Parts And Service Manual

    Division of EZ-8 Sander Section II Parts and Service Manual (78425C) American Sanders EZ - 8 Sander Operator's Manual Page 13 ® Clarke...

  • Page 14: Assembly Drawing #1 11/01

    EZ-8 Sander Assembly Drawing #1 11/01 11 12 19 12 Page 14 American Sanders EZ - 8 Sander Operator's Manual Clarke ®...

  • Page 15: Assembly Parts List #1

    EZ-8 Sander Assembly Drawing #1 7/03 Ref. # Part No. Description Ref. # Part No. Description 41949A Cord, Motor 915082 x ¾ 912169 Plug L5-15P 51178A Bearing, Arbor 962831 Screw Set 10-32 x 81211A Nut, Flanged 170686 Nut Conduit ½...

  • Page 16: Assembly Drawing #2 10/01

    EZ-8 Sander Assembly Drawing #2 10/01 39 38 13 14 Page 16 American Sanders EZ - 8 Sander Operator's Manual Clarke ®...

  • Page 17: Assembly Parts List #2 7/03

    EZ-8 Sander Assembly Parts List #2 7/03 Ref. # Part No. Description Ref. # Part No. Description 47387A Switch, Control 69106A Tube, Handle 24525A Housing Control 69107A Tube, Dust 81210A Nut, Fixture 50951A Bag, Dust 980675 Washer 68285A Support Tube...

  • Page 18: Wiring Diagram 9/92

    EZ-8 Sander Wiring Diagram 9/92 Page 18 American Sanders EZ - 8 Sander Operator's Manual Clarke ®...
  • Page 19 ALTO Nederland B.V. Vianen (770) 973-5225 Stuartweg 4C NL-4131 NJ Vianen +31 347 324000 Clarke ® Clarke American Sanders ALTO Sverige AB, Molndal (Sweden) A.L. Cook Aminogatan 18 Customer Service Headquarters and Factory Box 4029 2100 Highway 265 S-431 04 Molndal...
  • Page 20 (b). Return the product to the nearest Clarke American Sanders repair location. Transportation charges to and from the repair location must be prepaid by the purchaser. (c). Clarke American Sanders will repair the product and or replace any defective parts without charge within a reasonable time after receipt of the product.

Table of Contents