Arcam fmj UDP411 Handbook page 8

basic
operation
Introduction Loading a disc
Press < / 1 on the front panel (or on the handset)
'Basic operation' explains how to play a Blu-ray Disc 1
(BD), DVD, SACD, CD or other type of disc. Note that and place the disc on the tray, with the playback side
facing down (some discs are double sided, in which case
it may be necessary to configure your player correctly
for your system before optimum – or any – playback can the side labelled 'side A' should face up to play side A).
be achieved. Player configuration is described beginning
Press < / 1 on the front panel to close the tray. The disc
on page E-16.
loads after a pause of a few seconds.
More sophisticated features – such as special playback
Playing a disc
modes and programming jumps and playback sequences
– are described in the 'advanced operation' section, later A disc may take some time to load once the tray is
in this handbook. closed. When the 'Optical Disc Autoplay' setting is set to
On (the default setting), playback starts automatically.
Switching on (For details, refer to 'Optical Disc AutoPlay' on page
Switch the unit on by pressing the button. The E-17).
POWER
status LED glows green when the unit is powered up and
If Autoplay is set to Off, the player's Main Menu will
red when in standby mode. The remote control is used
appear on your TV. Use the cursor keys to select the disc
to enter and exit standby mode. If the button is
POWER in , then press O to start playback.
MY MEDIA
pressed (or power is removed) whilst in standby, the
Some titles begin by displaying a menu. Select the menu
unit will enter standby mode when power is re-applied.
item 'Play movie' (or similar) using the cursor pad, then
Note that the remote control sensor is located on the
press to start playback.
OK
right-hand side of the display window. Do not obstruct
For discs that do not play automatically, press
this or the remote control will not work.
the front panel or press on the remote control.
4
Fast play
NOTE
Press 8 or 7 on the front-panel or remote control to
When you press a button, if the unit does not accept
play fast forwards or backwards. The following speeds
its operation,  appears on the TV screen.
for fast playback are available: x2, x4, x8, x16 or x32
(depending on disc type). Press the button repeatedly Invalid operation may also occur if:
to cycle through the different speeds. To resume normal The region codes of the unit differs from that
<
playback speed, press .
PLAY of the disc, so playback is not allowed.
The parental control is set to prevent
<
Skipping chapters/tracks
operation: see 'Security/Parental Control' on
To skip chapters (or tracks on a CD), press / or 0 .
page E-18.
When skipping back, the first button press takes you to
< Some operations may be prohibited due to
the beginning of the current chapter. Pressing the button disc manufacturer's settings.
again takes you to the start of the previous chapter.
Pausing playback
Press 4 / ; on the front panel or ; on the remote
control to pause playback. To resume playback, press
4 / ; on the front panel or 4 on the handset.
Stopping playback
Press the < / 1 button on the front panel or < on the
4 / ; on
remote control to stop playback.
When playing a BD/DVD, pressing < once performs
a 'resume stop' . If you now press 4 , playback resumes
from the point it was stopped.
If you press < / 1 on the front panel or < on the remote
control twice, this is a 'complete stop' , and playback
resumes from the beginning of the disc.
E-10
remote
control
The UDP411 is supplied with the CR301 backlit remote
control.
Using the remote control
Please keep in mind the following when using the
remote control:
Ensure there are no obstacles between the
<
remote control and the remote sensor on the
front panel. The remote has a range of about 7
metres. (If the remote sensor is obscured, the IR
in remote control input jack on the rear panel is
available. Please consult your dealer for further
information.)
Remote operation may become unreliable if
<
strong sunlight or fluorescent light is shining on
the remote sensor of the unit.
Replace the batteries when you notice a reduction
<
in the operating range of the remote control.
Inserting batteries into the remote control
1. Open the battery compartment on the back of the
handset.
2. Insert two ' A AA' batteries according to the
diagram on the battery cover casing.
3. Slide the battery cover casing back into position
and lock it closed with a click.
Backlight
A backlight comes on for five seconds whenever a key
is pressed. This helps you use the handset in subdued
lighting conditions.
NOTE The CR301 remote complies with Part 15
of the FCC rules
Incorrect use of batteries can result in hazards
<
such as leakage and bursting. This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
Do not mix old and new batteries together.
<
part 15 of the FCC Rules. These limits are designed
Do not use non-identical batteries together
<
to provide a reasonable protection against harmful
– although they may look similar, different
interference in a residential installation. This
batteries may have different voltages.
equipment generates, uses, and can radiated radio
Ensure the plus (+) and minus (–) ends of
<
frequency energy and if not installed and used in
each battery match the indications in the
accordance with the instructions, may cause harmful
battery compartment.
interference to radio communications. However,
< Remove batteries from equipment that is not
there is no guarantee that interference will not occur
going to be used for a month or more.
in a particular installation. If this equipment does
< When disposing of used batteries, please
cause harmful interference to radio or television
comply with governmental or local regulations
reception, which can be determined by turning the
that apply in your country or area.
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet or a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
E-11