Page 1 Compass 2 0 1 3 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of fea- Chrysler Group LLC shall be deemed to be deleted and the tures and equipment that are either standard or optional on name Chrysler Canada Inc.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....7 ROLLOVER WARNING .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techni- Congratulations on selecting your new Chrysler Group cians and genuine parts, and cares about your satisfaction. LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all ROLLOVER WARNING essentials that are traditional to our vehicles.
Page 7: How To Use This Manual
INTRODUCTION 5 two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire.
Page 8 6 INTRODUCTION...
Page 9: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against oper- ating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
Page 10: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right Front Body VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ To Arm The System .....18 A WORD ABOUT YOUR KEYS ....12 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Lock The Doors And Liftgate ... .22 ▫ Child-Protection Door Lock System — Rear Doors ......34 ▫...
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belts In Passenger Seating Positions ..54 ▫ Air Bag Deployment Sensors And Controls ..68 ▫ Automatic Locking Retractor Mode (ALR) — ▫ Event Data Recorder (EDR) ....75 If Equipped .
Page 14: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your new vehicle has 1. Place the shift lever in PARK (if equipped with an the key code numbers for your vehicle locks. These automatic transmission).
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in PARK, rotate the key to the right slightly, then remove the key as described.
Page 16: Locking Doors With A Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locking Doors With A Key WARNING! (Continued) You can insert the key with either side up. To lock the • Allowing children to be in a vehicle unattended is door, turn the key to the right. To unlock the door, turn dangerous for a number of reasons.
Page 17: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY® During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for The Sentry Key® Immobilizer System prevents unau- three seconds for a bulb check. If the light remains on thorized vehicle operation by disabling the engine.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! CAUTION! The Sentry Key® Immobilizer system is not compat- Always remove the Sentry Keys® from the vehicle and ible with some after-market remote starting systems. lock all doors when leaving the vehicle unattended. Use of these systems may result in vehicle starting At the time of purchase, the original owner is provided problems and loss of security protection.
Page 19: Customer Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Customer Key Programming 4. Insert a blank Sentry Key® into the ignition switch. Turn the ignition switch to the ON/RUN position If you have two valid Sentry Keys®, you can program within 60 seconds. After 10 seconds, a single chime new Sentry Keys®...
Page 20: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized VEHICLE SECURITY ALARM — IF EQUIPPED dealer to have all remaining keys erased from the sys- This Vehicle Security Alarm monitors the doors, liftgate, tem’s memory.
Page 21: Rearming The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 3. The Vehicle Security Light in the instrument cluster To Disarm The System will flash rapidly for approximately 16 seconds. This Press UNLOCK on the RKE transmitter, or insert the key shows that the Vehicle Security Alarm is arming. into the ignition switch and turn the ignition switch to During this period, if a door is opened, the ignition the ON/RUN position.
Page 22: Vehicle Security Alarm Manual Override
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Vehicle Security Alarm Manual Override The Vehicle Security Alarm will not arm if you lock the doors using the manual door lock plunger. REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED This system allows you to lock or unlock the doors and liftgate or activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held Remote Keyless Entry (RKE) transmitter.
Page 23: To Unlock The Doors And Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • For vehicles not equipped with the EVIC, perform the To Unlock The Doors And Liftgate following steps: Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door, or twice 1.
Page 24: Illuminated Approach - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the RKE transmit- To Lock The Doors And Liftgate ter while you are inside the vehicle will activate the Press and release the LOCK button on the RKE transmit- Vehicle Security Alarm.
Page 25: Flash Lights With Remote Key Lock/Unlock
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, perform the NOTE: Pressing the LOCK button on the RKE transmit- following steps: ter while you are in the vehicle will activate the Vehicle Security Alarm.
Page 26: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the Alarm activated will cause the alarm to sound. Press the following steps: UNLOCK button to deactivate the Vehicle Security Alarm. 1. Press and hold the UNLOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer Using The Panic Alarm than 10 seconds.
Page 27: Programming Additional Transmitters
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Programming Additional Transmitters If your RKE transmitter fails to operate from a normal distance, check for these two conditions: Refer to Sentry Key® “Customer Key Programming.” 1. Weak battery in the RKE transmitter. The expected life If you do not have a programmed RKE transmitter, of a battery is five years.
Page 28: Remote Starting System - If Equipped
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the RKE transmitter is equipped with a screw, reinstall and tighten the screw until snug. REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security.
Page 29: How To Use Remote Start
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • System not disabled from previous remote start event How To Use Remote Start • Vehicle theft alarm not active All of the following conditions must be met before the engine will remote start: WARNING! •...
Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Abort Message On Electronic Vehicle To Enter Remote Start Information Center (EVIC) — If Equipped Press and release the REMOTE START button The following messages will display in the EVIC if the on the RKE transmitter twice within five sec- onds.
Page 31: To Exit Remote Start Without Driving
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • The engine can be started two consecutive times (two To Exit Remote Start Mode Without Driving The 15-minute cycles) with the RKE transmitter. However, Vehicle the ignition switch must be cycled to the ON/RUN Press and release the REMOTE START button one time or position before you can repeat the start sequence for a allow the engine to run for the entire 15-minute cycle.
Page 32: Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! Manual Door Locks • For personal security and safety in the event of an Use the manual door lock knob to lock the doors from collision, lock the vehicle doors as you drive as inside the vehicle.
Page 33: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 NOTE: To prevent from locking the key in the vehicle, WARNING! (Continued) the power door lock switch will not operate when the key • Do not leave the key fob in or near the vehicle, or is in the ignition and either front door is open.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Lock Doors — If Equipped 2. Within 15 seconds, cycle the ignition switch between LOCK and ON/RUN and then back to LOCK four The auto door lock feature default condition is enabled. times ending up in the LOCK position (do not start the When enabled, the door locks will lock automatically engine).
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Automatic Unlock Doors On Exit in “Understanding Your Instrument Panel” for further information. The doors will unlock automatically if: • For vehicles not equipped with the EVIC, perform the • The Automatic Unlock Doors On Exit feature is enabled. following procedure: •...
Page 36: Child-Protection Door Lock System - Rear Doors
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • If you do not hear the chime it means that the system did not enter the programming mode and you will need to repeat the procedure. • Use the Automatic Unlock Doors On Exit feature in accordance with local laws.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged. NOTE: For emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window and open the door with the outside door handle.
Page 38: Power Windows - If Equipped
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the EVIC, the power POWER WINDOWS — IF EQUIPPED window switches will remain active for up to 10 min- Power Window Switches utes after the ignition switch is turned to the LOCK The window controls on the driver’s door trim panel position.
Page 39: Auto-Down
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window LOCKOUT switch.
Page 40: Liftgate
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn it to the right (manual lock models only).
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: WARNING! • In the event of a power malfunction, or the RKE • Driving with the liftgate open can allow poisonous transmitter is inoperative, insert the key into the exhaust gases into your vehicle. You and your liftgate lock cylinder and turn to the right (manual lock passengers could be injured by these fumes.
Page 42: Occupant Restraints
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • An energy-absorbing steering column and steering OCCUPANT RESTRAINTS wheel Some of the most important safety features in your • Knee bolsters for front seat occupants vehicle are the restraint systems: • Three-point lap and shoulder belts for the driver and •...
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 If you will be carrying children too small for adult-sized WARNING! seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold Infants in rear facing child restraints should never infant and child restraint systems.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a child from 1 to 12 years old (not in a rear facing child 5. If the air bag system in this vehicle needs to be seat) must ride in the front passenger seat, move the seat modified to accommodate a disabled person, contact as far back as possible and use the proper child restraint.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Buckle up even though you are an excellent driver, even WARNING! (Continued) on short trips. Someone on the road may be a poor driver • Supplemental Side Air Bag Inflatable Curtain and cause a collision that includes you. This can happen (SABIC) and Seat-Mounted Side Air Bags (SAB) also far away from home or on your own street.
Page 46: Lap/Shoulder Belts
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts WARNING! (Continued) All seating positions in your vehicle are equipped with • Do not allow people to ride in any area of your lap/shoulder belts. vehicle that is not equipped with seats and seat belts. •...
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or lap belt for more than one person, no matter what their size.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt buckled into the wrong buckle will not protect you properly.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. WARNING! The belt will automatically retract to its stowed posi- • A lap belt worn too high can increase the risk of tion.
Page 51: Adjustable Upper Shoulder Belt Anchorage
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best.
Page 52: Second Row Center Lap/Shoulder Belt Operating Instructions
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Second Row Center Lap/Shoulder Belt Operating Instructions The second row center lap/shoulder belt features a three-point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach from the lower anchor when the seat is folded.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 3. Route the shoulder belt to the inside of the right head 5. Sit back in the seat. Slide the regular latch plate up the restraint. webbing as far as necessary to allow the belt to go around your lap.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7. Position the lap belt across your thighs, below your 8. Position the shoulder belt on your chest so that it is abdomen. To remove slack in the lap belt portion, pull comfortable and not resting on your neck.
Page 55: Lap/Shoulder Belt Untwisting Procedure
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 10. To disengage the mini-latch from the mini-buckle Lap/Shoulder Belt Untwisting Procedure for storage, insert the regular latch plate into the Use the following procedure to untwist a twisted lap/ black button on the top of the mini-buckle. The belt shoulder belt.
Page 56: Seat Belts In Passenger Seating Positions
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts In Passenger Seating Positions If the passenger seating position is equipped with an ALR and is being used for normal usage: The seat belts in the passenger seating positions are equipped with Automatic Locking Retractors (ALR) Only pull the belt webbing out far enough to comfortably which are used to secure a child restraint system.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 lap/shoulder belt. Use the Automatic Locking Mode any- How To Disengage The Automatic Locking Mode time a child safety seat is installed in a seating position that Unbuckle the combination lap/shoulder belt and allow it has a belt with this feature.
Page 58: Energy Management Feature
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Energy Management Feature NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be This vehicle has a safety belt system with an Energy worn snugly and positioned properly.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 How The Active Head Restraints (AHR) Work The Occupant Restraint Controller (ORC) determines whether the severity, or type of rear impact will require the Active Head Restraints (AHR) to deploy. If a rear impact requires deployment, both the driver and front passenger seat AHRs will be deployed.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 3 — Final Downward Movement To Engage Locking Mechanism 4. The AHR front soft foam and trim half should lock into the back decorative plastic half.
Page 62: Enhanced Seat Belt Use Reminder System (Beltalert®)
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert®) BeltAlert® is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert®) to fasten their seat belts. The feature is active whenever the ignition is on.
Page 63: Seat Belt Extender
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 unbuckled while traveling at speeds greater than 5 mph Seat Belt Extender (8 km/h), BeltAlert® will provide both audio and visual If a seat belt is too short even when fully extended and notification.
Page 64: Seat Belts And Pregnant Women
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 The Advanced Front Air Bags have a multistage inflator This vehicle is equipped with Supplemental Side Air Bag design. This allows the air bag to have different rates Inflatable Curtains (SABIC) to protect the driver, front, of inflation that are based on the severity and type of and rear passengers sitting next to a window.
Page 66: Advanced Front Air Bag Features
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front and Side Impact Sensors Air Bag System Components • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, Your vehicle may be equipped with the following air bag system components: and Seat Track Position Sensors •...
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Supplemental Seat-Mounted Side Air Bags (SAB) WARNING! Supplemental Seat-Mounted Side Air Bags (SAB) may • No objects should be placed over or near the air bag provide enhanced protection to help protect an occupant on the instrument panel, because any such objects during a side impact.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • Air Bag covers may not be obvious in the interior trim, WARNING! (Continued) but they will open during air bag deployment. • Do not use accessory seat covers or place objects •...
Page 70: Air Bag Deployment Sensors And Controls
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE children, should not lean on or sleep against the door, Air Bag Deployment Sensors And Controls side windows, or area where the SAB or SABIC air bags Occupant Restraint Controller (ORC) inflate, even if they are in an infant or child restraint. The ORC is part of a Federally regulated safety system Always sit upright as possible with your back against the required for this vehicle.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 The Advanced Front Air Bags will not deploy in all The ORC monitors the readiness of the electronic parts of frontal collisions, including some that may produce sub- the air bag system whenever the ignition switch is in the stantial vehicle damage —...
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE It also includes diagnostics that will illuminate the instru- When the ORC detects a collision requiring the ment cluster Air Bag Warning Light if a malfunction is Advanced Front Air Bags, it signals the inflator units. noted that could affect the air bag system.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Supplemental Seat-Mounted Side Air Bag (SAB) Supplemental Side Air Bag Inflatable Curtain Inflator Units (SABIC) Inflator Units The Supplemental Seat-Mounted Side Air Bags (SAB) are During collisions where the impact is confined to a designed to activate only in certain side collisions.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Flash hazard lights as long as the battery has power or Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of until the ignition key is turned off. whether or not an air bag should have deployed.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 If you do have a collision, which deploys the air bags, any irritation, rinse the area with cool water. For nose or or all of the following may occur: throat irritation, move to fresh air. If the irritation continues, see your doctor.
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or may • Modifications to any part of the air bag system not function properly if modifications are made.
Page 77: Event Data Recorder (Edr)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint You will want to have the air bags ready to Controller (ORC) may also be disabled. The air bags may inflate for your protection in a collision.
Page 78: Child Restraints
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle dynamics and safety systems for a short period of are recorded. However, other parties, such as law en- time, typically 30 seconds or less. The EDR in this vehicle forcement, could combine the EDR data with the type of is designed to record such data as: personally identifying data routinely acquired during a crash investigation.
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Children 12 years or younger should ride properly NOTE: For additional information, refer to buckled up in a rear seat, if available. According to crash www.seatcheck.org or call 1–866–SEATCHECK. statistics, children are safer when properly restrained in Canadian residents should refer to Transport the rear seats rather than in the front.
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight or Age Recommended Type of Child Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Convertible younger and who have not reached Child Restraint, facing rearward in the the height or weight limits of their...
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Infants And Child Restraints their infant carrier but are still less than at least two years old. Children should remain rearward-facing until they Safety experts recommend that children ride rearward- reach the highest weight or height allowed by their facing in the vehicle until they are two years old or until convertible child seat.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children And Child Restraints the seatback, they should use a belt-positioning booster seat. The child and belt-positioning booster seat are held Children who are two years old or who have outgrown in the vehicle by the seat belt.
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Children Too Large For Booster Seats 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 5.
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – LATCH – Child + Child Lower Anchors Seat Belt + Top Lower Anchors Seat Belt Only Restraint...
Page 85 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Lower Anchors and Tethers for Children (LATCH) Your vehicle is equipped with the child restraint anchor- Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol...
Page 87 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 What is the weight limit (child’s weight 65 lbs (29.5 kg) Use the LATCH anchorage system until + weight of the child restraint) for using the combined weight of the child and the LATCH anchorage system to attach the child restraint is 65 lbs (29.5 kg).
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can two child restraints be attached Never “share” a LATCH anchorage using a common lower with two or more child restraints. If the LATCH anchorage? center position does not have dedicated LATCH lower anchorages, use the seat belt to install a child seat in the center position next to a child seat using the LATCH anchorages in an outboard...
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraint systems will be WARNING! equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower Never use the same lower anchorage to attach more anchorage and a way to tighten the connection to the than one child restraint.
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 To Install A LATCH-compatible Child Restraint 4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- 1. If the selected seating position has a Switchable Auto- ing position.
Page 92 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Stow An Unused ALR Seatbelt WARNING! When using the LATCH attaching system to install a Improper installation of a child restraint to the child restraint, stow all ALR seat belts that are not being LATCH anchorages can lead to failure of the re- used by other occupants or being used to secure child straint.
Page 93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 not necessary to use a locking clip. The ALR retractor can Lap/Shoulder Belt Systems for Installing Child be “switched” into a locked mode by pulling all of the Restraints in this Vehicle webbing out of the retractor and then letting the webbing retract back into the retractor.
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight Weight limit of the Always use the tether anchor when + weight of the child restraint) for using Child Restraint using the seat belt to install a forward the Tether Anchor with the seat belt to facing child restraint, up to the attach a forward facing child restraint?
Page 95 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Installing A Child Restraint with a Switchable 5. To lock the seat belt, pull down on the shoulder part of Automatic Locking Retractor (ALR) the belt until you have pulled all the seat belt webbing out of the retractor.
Page 96 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 8. If the child restraint has a top tether strap and the Installing A Child Restraint With A Cinching seating position has a top tether anchorage, connect Latch Plate (CINCH) — If Equipped the tether strap to the anchorage and tighten the tether 1.
Page 97 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 5. If the child restraint has a top tether strap and the If the buckle or the cinching latch plate is too close to the seating position has a top tether anchorage, connect belt path opening of the child restraint, you may have the tether strap to the anchorage and tighten the tether trouble tightening the seat belt.
Page 98 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using The Top Tether Anchorage 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage.
Page 99: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine and An incorrectly anchored tether strap could lead to drivetrain (transmission and axle) in your vehicle. increased head motion and possible injury to the child. Drive moderately during the first 300 miles (500 km).
Page 100: Safety Tips
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! WARNING! • Do not leave children or animals inside parked Never use Non-Detergent Oil or Straight Mineral Oil vehicles in hot weather. Interior heat build-up may in the engine or damage may result. cause serious injury or death.
Page 101: Exhaust Gas
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Exhaust Gas The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust WARNING! system. Exhaust gases can injure or kill. They contain carbon Whenever a change is noticed in the sound of the exhaust monoxide (CO), which is colorless and odorless.
Page 102: Safety Checks You Should Make Inside The Vehicle
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The dealer. If the light stays on, flickers, or comes on while Vehicle driving, have the system checked by an authorized dealer. Seat Belts Defroster Inspect the belt system periodically, checking for cuts, frays, and loose parts.
Page 103 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 WARNING! WARNING! (Continued) • Check mounting of mats on a regular basis. Always Pedals that cannot move freely can cause loss of properly reinstall and secure floor mats that have vehicle control and increase the risk of serious per- been removed for cleaning.
Page 104: Periodic Safety Checks You Should Make Outside The Vehicle
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 105: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS MIRRORS ......107 Uconnect® Phone — IF EQUIPPED ..111 ▫...
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Commands ......144 TO OPEN AND CLOSE THE HOOD ..161 ▫...
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 WINDSHIELD WIPERS AND WASHERS ..168 GARAGE DOOR OPENER — IF EQUIPPED . . .176 ▫ Windshield Wiper Operation ... . .170 ▫...
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Closing Sunroof — Manual Mode ..187 CONSOLE FEATURES ....197 ▫...
Page 109: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle).
Page 110: Automatic Dimming Mirror - If Equipped
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
Page 111: Outside Mirror - Driver Side
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Outside Mirror — Driver Side WARNING! Adjust the flat outside mirror so you can just see the side Vehicles and other objects seen in the passenger side of your vehicle in the part of the mirror closest to the convex mirror will look smaller and farther away vehicle with your head close to the door glass.
Page 112: Power Mirrors
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand The power mirror control is located on the driver’s door in the direction you want the mirror to move. trim panel.
Page 113: Sun Visor Sliding Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Uconnect® Phone — IF EQUIPPED Uconnect® Phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect® Phone allows you to dial a phone number with your mobile phone using simple voice commands (e.g., “Call” “Mike” “Work” or “Dial”...
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect® Phone allows you to transfer calls between WARNING! the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s Any voice commanded system should be used only microphone for private conversation.
Page 115: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Voice Command Button Operation Voice commands can be used to operate the Uconnect® Actual button location may vary with the ra- Phone and to navigate through the Uconnect® Phone dio. The individual buttons are described in the menu structure.
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For each feature explanation in this section, only To activate the Uconnect® Phone, simply press the the compound form of the voice command is given. button and follow the audible prompts for directions. You can also break the commands into parts and say Uconnect®...
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • You will then be asked to give your mobile phone a The following are general phone to Uconnect® Phone priority level between one and seven, with one being pairing instructions: the highest priority. You can pair up to seven mobile •...
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the number you or downloaded phonebook. To learn how to store a want to call. name in the phonebook, refer to “Add Names to Your Uconnect®...
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 • When prompted, enter the number designation Phonebook Download – Automatic Phonebook (e.g., “Home”, “Work”, “Mobile”, or “Other”). This Transfer From Mobile Phone will allow you to store multiple numbers for each If equipped and specifically supported by your phone, phonebook entry, if desired.
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • A maximum of 1000 entries per phone will be down- Edit Uconnect® Phonebook Entries loaded and updated every time a phone is connected NOTE: to the Uconnect® Phone. • Editing names in the phonebook is recommended •...
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • After you enter the Phonebook Delete menu, you will After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in then be asked for the name of the entry that you wish the phonebook, call the number you just edited, or return to delete.
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete/Erase “All” Uconnect® Phonebook Entries List All Names In The Uconnect® Phonebook • Press the • Press the button to begin. button to begin. • After the “Ready” prompt and the following beep, say •...
Page 123: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Phone Call Features Answer Or Reject An Incoming Call — Call Currently In Progress The following features can be accessed through the Uconnect® Phone if the feature(s) are available on your If a call is currently in progress and you have another mobile service plan.
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE call. The first call will be on hold while the second call is Conference Call in progress. To go back to the first call, refer to “Toggling When two calls are in progress (one active and one on Between Calls”...
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Call Termination Call Continuation To end a call in progress, momentarily press the but- Call continuation is the progression of a phone call on the ton. Only the active call(s) will be terminated and if there Uconnect®...
Page 126: Uconnect® Phone Features
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect® Phone Features Emergency Assistance If you are in an emergency and the mobile phone is Language Selection reachable: To change the language that the Uconnect® Phone is • Pick up the phone and manually dial the emergency using: number for your area.
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 NOTE: WARNING! • The emergency number dialed is based on the country To use you Uconnect® Phone System in an emer- where the vehicle is purchased (911 for the U.S. and gency, your mobile phone must be: Canada and 060 for Mexico).
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Voice Mail Calling • The roadside assistance number dialed is based on the To learn how to access your voice mail, refer to “Working with Automated Systems”. country where the vehicle is purchased (1-800-528-2069 for the U.S., 1-877-213-4525 for Canada, 55-14-3454 for Working With Automated Systems Mexico City and 1-800-712-3040 for outside Mexico City...
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 followed by the word “Send”. For example, if required to NOTE: enter your PIN followed with a pound, (3 7 4 6 #), you • You may not hear all of the tones due to mobile phone can press the button and say, “3 7 4 6 # Send”.
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts ON/OFF Dialing Using The Mobile Phone Keypad Turning confirmation prompts off will stop the system You can dial a phone number with your mobile phone from confirming your choices (e.g., the Uconnect® Phone keypad and still use the Uconnect®...
Page 131: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Mute/Un-Mute (Mute ON/OFF) from your Uconnect® Phone paired mobile phone to the Uconnect® Phone or vice versa, press the button When you mute the Uconnect® Phone, you will still be and say “Transfer Call”. able to hear the conversation coming from the other party, but the other party will not be able to hear you.
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say “List Phones”. • The selected phone will be used for the next phone call. If the selected phone is not available, the • The Uconnect® Phone will play the phone names of all Uconnect®...
Page 133: Things You Should Know About Your Uconnect® Phone
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Things You Should Know About Your Uconnect® You can either press the Uconnect® Phone button to restore Phone the factory setting or repeat the words and phrases when prompted by the Uconnect® Phone. For best results, the Uconnect®...
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Even though the system is designed for users speaking Voice Command in North American English, French, and Spanish ac- • For best performance, adjust the rearview mirror to cents, the system may not always work for some. provide at least ½...
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • Even though international dialing for most number • Performance, such as audio clarity, echo, and loudness combinations is supported, some shortcut dialing to a large degree rely on the phone and network, and number combinations may not be supported.
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Read Messages: Send Messages: If you receive a new text message while your phone is You can send messages using Uconnect® Phone. To send connected to Uconnect® Phone, an announcement will a new message: be made to notify you that you have a new text message.
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 List of Preset Messages: 11. See You in 15 minutes 1. Yes 12. I am on my way 2. No 13. I’ll be late 3. Where are you? 14. Are you there yet? 4.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn SMS Incoming Announcement ON/OFF Bluetooth® Communication Link Mobile phones have been found to lose connection to the Turning the SMS Incoming Announcement OFF will Uconnect® Phone. When this happens, the connection stop the system from announcing the new incoming can generally be reestablished by switching the phone messages.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137...
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139...
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate (s) Primary Alternate (s) zero call cancel three confirmation prompts four continue five delete dial seven download eight edit nine emergency star (*) English plus (+) erase all pound (#) Espanol add location...
Page 143 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Voice Commands Voice Commands Primary Alternate (s) Primary Alternate (s) help previous home record again language redial list names return to main menu return or main menu list phones select phone select mobile send mute set up...
Page 144: General Information
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada. Operation is subject to the The Uconnect® Voice Command system allows following conditions: you to control your AM, FM radio, disk player, •...
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Pressing the Voice Command button while the WARNING! system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or Any voice commanded system should be used only change commands.
Page 146: Commands
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE At any point, if the system does not recognize one of your Main Menu commands, you will be prompted to repeat it. Start a dialogue by pressing the Voice Command To hear the first available Menu, press the Voice Com- button.
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 • “Menu Radio” (to switch to the radio menu) Radio AM • “Main Menu” (to switch to the main menu) To switch to the AM band, say “AM” or “Radio AM”. In this mode, you may say the following commands: Satellite Radio •...
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Disc Mode – “Continue” (to continue recording) – “Delete” (to delete the recording) To switch to the disc mode, say “Disc”. In this mode, you • “Play Memos” (to play previously recorded memos) — may say the following commands: During the playback you may press the Voice Com- •...
Page 149: Voice Training
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 • “Change to setup” Voice Training • “Main menu setup” or For users experiencing difficulty with the system recog- nizing their voice commands or numbers the Uconnect® • “Switch to setup” Voice “Voice Training” feature may be used. In this mode, you may say the following commands: 1.
Page 150: Seats
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Power Seats — If Equipped Seats are a part of the Occupant Restraint System of the Some models may be equipped with a power driver’s vehicle. seat. The power seat switch is located on the outboard side of the seat near the floor.
Page 151 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Adjusting The Seat Forward Or Rearward WARNING! The seat can be adjusted both forward and rearward. • Adjusting a seat while driving may be dangerous. Push the seat switch forward or rearward, the seat will Moving a seat while driving could result in loss of move in the direction of the switch.
Page 152: Heated Seats - If Equipped
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped 30 minutes of continuous operation. At that time, the display will change from HI to LO, indicating the change. On some models, the front driver and passenger seats When the LOW-level heating is selected, the system may be equipped with heaters in both the seat cushions automatically turns the heater and the indicator light...
Page 153: Manual Front Seat Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WARNING! (Continued) • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat.
Page 154: Manual Seat Height Adjustment - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped WARNING! The driver’s seat height can be raised or lowered by using • Adjusting a seat while driving may be dangerous. a lever, located on the outboard side of the seat. Pull Moving a seat while driving could result in loss of upward on the lever to raise the seat height or push control which could cause a collision and serious...
Page 155: Manual Lumbar - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Manual Lumbar — If Equipped Driver’s Seatback Recline The lumbar adjustment handle is located on the outboard To adjust the seatback, lift the lever located on the side of the driver’s seatback. Rotate the lever downward outboard side of the seat, lean back to the desired angle to increase the lumbar support or rotate the lever upward and release the lever.
Page 156: Fold-Flat Front Passenger Seat
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Fold-Flat Front Passenger Seat To fold the front passenger seat, lift the recliner handle to the full upward position and push the seatback forward...
Page 157: Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Head Restraints Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a...
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Active Head Restraints — Front Seats To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push Active Head Restraints are passive, deployable compo- button, located at the base of the head restraint, and push nents, and vehicles with this equipment cannot be readily downward on the head restraint.
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: WARNING! (Continued) • The head restraints should only be removed by quali- • Active Head Restraints may be deployed if they are fied technicians, for service purposes only. If either of struck by an object such as a hand, foot or loose the head restraints require removal, see your autho- cargo.
Page 161: Folding Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to fold the rear seatback flat. Folded Rear Seat To raise the seatback, pull the strap forward and lift the seatback into its upright position.
Page 162: Reclining Rear Seat - If Equipped
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! Be certain that the seatback is securely locked into Do not ride with the seatback reclined so that the position. If the seatback is not securely locked into shoulder belt is no longer resting against your chest. position the seat will not provide the proper stability In a collision you could slide under the seat belt and for child seats and/or passengers.
Page 163: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 TO OPEN AND CLOSE THE HOOD 2. Move the safety latch, located outside the vehicle under the front edge of the hood, toward the center To open the hood, two latches must be released. and raise the hood.
Page 164 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lift the hood prop rod, clipped to the right side (left side CAUTION! facing hood) of the engine compartment to secure the hood in the open position. Place the hood prop at the To prevent possible damage, do not slam the hood to location stamped into the inner hood surface.
Page 165: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 LIGHTS Multifunction Lever The multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and the fog lights. The multifunction lever is located on the left side of the steering column.
Page 166: Headlights And Parking Lights
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights And Parking Lights Daytime Running Lights — If Equipped Turn the end of the multifunction lever to the first detent The high beam lights will come on as Daytime Running to turn on the parking lights. Turn the end of the lever to Lights (lower intensity), whenever the ignition is ON, the the second detent to turn on the headlights.
Page 167: Turn Signals
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Front Fog Light Operation NOTE: The fog lights will only operate with the head- lights on low beam.
Page 168: High/Low Beam Switch
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If either light remains on and does not flash, or Flash-To-Pass there is a very fast flash rate, check for a defective outside You can signal another vehicle with your headlights by light bulb.
Page 169 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on. Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are on.
Page 170: Map/Reading Lights
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Map/Reading Lights NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned These lights are mounted between the sun visors above off before leaving the vehicle. They will not turn off the rear view mirror.
Page 171 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. •...
Page 172: Windshield Wiper Operation
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Intermittent Wiper System Rotate the end of the lever upward to the second detent Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, past the intermittent settings for low-speed wiper opera- desirable.
Page 173: Mist Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 If the lever is pulled while in the off position, the wipers NOTE: The mist feature does not activate the washer will operate for two wipe cycles, then turn off. pump; therefore, no washer fluid will be sprayed on the windshield.
Page 174: Tilt Steering Column
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt steering column lever is located on the left side of the steering column, below the turn signal lever. Push down on the lever to unlock the steering column.
Page 175: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 176: To Activate
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control System has been designed to shut Leaving the Electronic Speed Control system on down if multiple Speed Control functions are operated at when not in use is dangerous.
Page 177: To Deactivate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 To Deactivate Pressing the RES (+) button once will result in a 1 mph (1.6 km/h) increase in set speed. Each subsequent tap of A soft tap on the brake pedal, pushing the CANCEL the button results in an increase of 1 mph (1.6 km/h).
Page 178: Garage Door Opener - If Equipped
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using Electronic Speed Control On Hills GARAGE DOOR OPENER — IF EQUIPPED The transmission may downshift on hills to maintain the HomeLink® replaces up to three hand-held transmitters vehicle set speed. that operate devices such as garage door openers, motor- ized gates, lighting or home security systems.
Page 179 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 HomeLink® Buttons/Sunvisor/Headliner HomeLink® Buttons/Overhead Consoles NOTE: HomeLink® is disabled when the Vehicle Secu- rity Alarm is active.
Page 180: Before You Begin Programming Homelink
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Before You Begin Programming HomeLink® NOTE: • Erasing all channels should only be performed when Be sure that your vehicle is parked outside of the garage before you begin programming. programming HomeLink® for the first time. Do not erase channels when programming additional buttons.
Page 181 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to pro- gram while keeping the HomeLink® indicator light in view.
Page 182 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. At the garage door opener motor (in the garage), To program the remaining two HomeLink® buttons, locate the “LEARN” or “TRAINING” button. This can repeat each step for each remaining button. DO NOT usually be found where the hanging antenna wire is erase the channels.
Page 183: Programming A Non-Rolling Code
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Programming A Non-Rolling Code 4. Continue to hold both buttons and observe the indi- cator light. The Homelink® indicator will flash slowly For programming Garage Door Openers manufactured and then rapidly after HomeLink® has received the before 1995.
Page 184: Canadian/Gate Operator Programming
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink® Button Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- To reprogram a channel that has been previously trained, mission – which may not be long enough for HomeLink® follow these steps: to pick up the signal during programming.
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 • To program the two remaining HomeLink® buttons, 3. Continue to press and hold the HomeLink® button, while you press and release (“cycle”), your hand-held repeat each step for each remaining button. DO NOT transmitter every two seconds until HomeLink®...
Page 186: Using Homelink
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink® Troubleshooting Tips To operate, press and release the programmed HomeLink® If you are having trouble programming HomeLink®, button. Activation will now occur for the programmed here are some of the most common solutions: device (i.e., garage door opener, gate operator, security •...
Page 187: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 General Information WARNING! This device complies with FCC rules Part 15 and Industry • Your motorized door or gate will open and close Canada RSS-210. Operation is subject to the following while you are programming the universal trans- two conditions: ceiver.
Page 188: Power Sunroof - If Equipped
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located on the overhead • Never leave children in a vehicle with the key in console. the ignition switch. Occupants, particularly un- attended children, can become entrapped by the power sunroof while operating the power sunroof switch.
Page 189: Opening Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Opening Sunroof — Express position. The sunroof will close fully and stop automati- cally. This is called “Express Close”. During Express Press the switch rearward and release it within one-half Close operation, any movement of the switch will stop second.
Page 190: Venting Sunroof - Express
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If three consecutive sunroof close attempts re- Wind Buffeting sult in Pinch Protect reversals, the fourth close attempt Wind buffeting can be described as the perception of will be a Manual Close movement with Pinch Protect pressure on the ears or a helicopter-type sound in the disabled.
Page 191: Ignition Off Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Ignition Off Operation ELECTRICAL POWER OUTLETS For Vehicles Not Equipped With The Electronic Vehicle There is a standard 12 Volt (13 Amp) power outlet located in the instrument panel for added convenience. This Information Center (EVIC) power outlet can power mobile phones, electronics and The power sunroof switch will remain active for 45 seconds...
Page 192 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power is available when the ignition switch is in the ON or ACC position. Insert the cigar lighter or accessory plug into the outlet for use. To preserve the heating element, do not hold the lighter in the heating position. NOTE: To ensure proper operation a MOPAR®...
Page 193 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 WARNING! CAUTION! • Many accessories that can be plugged in draw power To avoid serious injury or death: • Only devices designed for use in this type of outlet from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 194: Power Inverter - If Equipped
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. A 115 Volt (150 Watt) AC power inverter is located on the front of the center console for added convenience.
Page 195 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 WARNING! CAUTION! • Many accessories that can be plugged in draw power To avoid serious injury or death: • Do not use a three-prong adaptor. from the vehicle’s battery, even when not in use (i.e., •...
Page 196: Cupholders
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS There are two cupholders located in the back for the rear passengers. Your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. Rear Cupholders Front Cupholders...
Page 197: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 STORAGE To open the lower glove compartment, pull outward on the release handle. Glove Compartment And Storage Bin Located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. Glove Compartment Storage Bins 1 —...
Page 198: Door Storage
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Storage The interior door panels are equipped with lower storage areas. Rear Door Storage Front Door Storage...
Page 199: Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 CONSOLE FEATURES To open the lower storage compartment, lift upward on the lower handle to unlatch the lower storage compart- The floor console contains both an upper and lower ment and lift the lid open. storage compartment.
Page 200: Cargo Area Features
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE light bulbs and is powered by rechargeable lithium WARNING! batteries that recharge when snapped back into place for convenience. Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music Press in on the flashlight to release it.
Page 201: Cargo Cover
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 To operate the flashlight, press the switch once for high, To install the Cargo Cover, insert either end of the cover twice for low, and a third time to return to off. into one of the two notches located in the rear trim panels.
Page 202 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the handle, pull the cover toward you and guide WARNING! the rear cover posts into the guides located on both sides of the rear trim panel. In a collision a cargo cover loose in the vehicle could cause injury.
Page 203: Removable Load Floor
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Removable Load Floor Cargo Tie-Down Loops The cargo area load floor is removable and can be There are four tie-downs (D-rings) installed in the cargo washed with mild soap and water. area for securing cargo. Removable Load Floor Cargo Area Tie-Downs...
Page 204 202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Place as much cargo as possible in front of the rear • Cargo tie-down loops are not safe anchors for a axle. Too much weight or improperly placed weight child seat tether strap.
Page 205: Fold Down Speakers - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Fold Down Speakers — If Equipped REAR WINDOW FEATURES Rear Window Wiper/Washer When the liftgate is open, the speakers can swing down off the trim panel to face rearward, for tailgating and The rear wiper/washer is controlled by a rotary switch other activities.
Page 206: Rear Window Defroster
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the center portion of the lever upward to Rear Window Defroster the first detent position for rear wiper operation. The rear window defroster button is located on the bottom right-side of the blower control knob. NOTE: The rear wiper operates in an intermittent mode Press this button to turn on the rear window defroster only.
Page 207: Roof Luggage Rack - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 ROOF LUGGAGE RACK — IF EQUIPPED CAUTION! The crossbars and siderails are designed to carry the Failure to follow these cautions can cause damage to weight on vehicles equipped with a luggage rack. The the heating elements: load must not exceed 150 lbs (68 kg), and should be •...
Page 208 206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The optional crossbars must also be secured in one of the For improved satellite radio reception, place the rear seven detent positions marked with an arrow on the crossbar in the second detent from the rear of the siderails to prevent movement.
Page 209 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 CAUTION! (Continued) WARNING! • To avoid damage to the roof rack and vehicle, do not Cargo must be securely tied before driving your exceed the maximum roof rack load capacity of 150 lb vehicle.
Page 211: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ EVIC Functions ..... . .234 INSTRUMENT PANEL FEATURES...212 ▫...
Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® 230 — AM/FM STEREO RADIO Uconnect® 130 ......263 AND 6–DISC CD/DVD CHANGER ▫...
Page 213 UNDERSTANDING YOUR INSTRUMENT PANEL 211 iPod®/USB/MP3 CONTROL — IF EQUIPPED . .288 STEERING WHEEL AUDIO CONTROLS ..296 ▫ Connecting The iPod® Or External USB ▫ Radio Operation ..... .297 Device .
Page 214: Instrument Panel Features
212 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 5 — Storage Bin 9 — Heated Seat Switch – If Equipped 2 — Demisters 6 — Glove Compartment 10 — Hazard Warning Flasher 3 — Instrument Cluster 7 —...
Page 215: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 213 INSTRUMENT CLUSTER...
Page 216: Instrument Cluster Descriptions
214 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. 1. Fuel Gauge / Fuel Door Reminder 3. Electronic Throttle Control (ETC) Light When the ignition switch is in the ON/RUN This light informs you of a problem with the position, the pointer will show the level of fuel Electronic Throttle Control (ETC) system.
Page 217 UNDERSTANDING YOUR INSTRUMENT PANEL 215 4. Oil Pressure Warning Light 7. Air Bag Warning Light This light indicates low engine oil pressure. The This light will turn on for four to eight seconds light should turn on momentarily when the engine is as a bulb check when the ignition switch is first started.
Page 218 216 UNDERSTANDING YOUR INSTRUMENT PANEL 9. High Beam Indicator brakes. If the ABS light does not turn on when the ignition switch is turned to the ON/RUN position, have This indicator shows that the high beam head- the light inspected by an authorized dealer. lights are on.
Page 219 UNDERSTANDING YOUR INSTRUMENT PANEL 217 13. Engine Temperature Warning Light 14. Brake Warning Light This light warns of an overheated engine condi- This light monitors various brake functions, tion. As engine coolant temperatures rise and the including brake fluid level and parking brake gauge approaches H, this indicator will illuminate and a application.
Page 220 218 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capac- WARNING! (Continued) ity in the event of a failure to a portion of the hydraulic It will take longer to stop the vehicle. You could have system.
Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL 219 The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON/RUN position. If you continue operating the vehicle when the NOTE: This light shows only that the parking brake is Transmission Temperature Warning Light is illumi- applied.
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher tempera- WARNING! ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to A hot engine cooling system is dangerous. You or exceed the upper limits of the normal operating range.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 221 20. Shift Lever Indicator by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a The Shift Lever Indicator is self-contained within the different size than the size indicated on the vehicle instrument cluster.
Page 224 222 UNDERSTANDING YOUR INSTRUMENT PANEL Please note that the TPMS is not a substitute for proper TPMS from functioning properly. Always check the tire maintenance, and it is the driver’s responsibility to TPMS malfunction telltale after replacing one or more maintain correct tire pressure, even if under-inflation has tires or wheels on your vehicle, to ensure that the not reached the level to trigger illumination of the TPMS...
Page 225 UNDERSTANDING YOUR INSTRUMENT PANEL 223 23. Odometer Display / Trip Odometer Display Area Vehicle Odometer Messages When the appropriate conditions exist, the following This display indicates the total distance the vehicle has odometer messages will display: been driven. door ......Door Ajar NOTE: U.S.
Page 226 224 UNDERSTANDING YOUR INSTRUMENT PANEL gASCAP HOTOIL If the vehicle diagnostic system determines that the fuel When this message is displayed there is a engine over- filler cap is loose, improperly installed, or damaged, a temperature condition. When this condition occurs, the “gASCAP”...
Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 225 dependent upon your personal driving style. Unless 24. Malfunction Indicator Light (MIL) reset, this message will continue to display each time you The Malfunction Indicator Light (MIL) is part of turn the ignition switch to the ON/RUN position. To turn an Onboard Diagnostic system called OBD II that off the message temporarily, press and release the Trip monitors emissions, engine, and automatic trans-...
Page 228 226 UNDERSTANDING YOUR INSTRUMENT PANEL 25. Front Fog Light Indicator — If Equipped CAUTION! This indicator will illuminate when the front fog Prolonged driving with the Malfunction Indicator lights are on. Light (MIL) on could cause damage to the engine 26.
Page 229 UNDERSTANDING YOUR INSTRUMENT PANEL 227 running, a malfunction has been detected in the ESC 28. 4WD! Warning Light — If Equipped system. If this light remains on after several ignition This light monitors the 4-Wheel Drive (4WD) cycles, and the vehicle has been driven several miles system.
Page 230: Mini-Trip Computer - If Equipped
228 UNDERSTANDING YOUR INSTRUMENT PANEL 30. Hill Descent Indicator — If Equipped Control Buttons The symbol illuminates (is armed) when the 4WD Lock switch is activated and the trans- mission range indicator is in LOW or REVERSE position (Off-Road Mode). MINI-TRIP COMPUTER —...
Page 231 UNDERSTANDING YOUR INSTRUMENT PANEL 229 STEP Button Trip Odometer (ODO) Press the STEP button located on the steering wheel to This display shows the distance traveled since the last scroll through sub menus (i.e., Temperature, Trip Func- reset. Press and release the STEP button on the instru- tions: Odometer, Trip A, Trip B).
Page 232: Electronic Vehicle Information Center (Evic) - If Equipped
230 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER The EVIC consists of the following: (EVIC) — IF EQUIPPED • System Status The Electronic Vehicle Information Center (EVIC) fea- • Units tures a driver-interactive display that is located in the •...
Page 233 UNDERSTANDING YOUR INSTRUMENT PANEL 231 The system allows the driver to select information by MENU Button pressing the following buttons mounted on the steering Press and release the MENU button to scroll wheel: through the main menus (Fuel Economy, Warn- ings, Timer, Units, System, Personal Settings) or to exit sub-menus.
Page 234 232 UNDERSTANDING YOUR INSTRUMENT PANEL • Door Ajar (with vehicle graphic showing which door is When the appropriate conditions exist, the EVIC displays the following messages: open. A single chime sounds if the vehicle is in motion). • Turn Signal On (with a continuous warning chime •...
Page 235: Engine Oil Change Indicator System
UNDERSTANDING YOUR INSTRUMENT PANEL 233 • Key In Ignition Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN • Low Tire position. To turn off the message temporarily, press and • Low Tire Pressure Display for Premium TPM System release the Trip Odometer button on the instrument cluster.
Page 236: Evic Functions
234 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC Functions SELECT button a second time within three seconds of resetting the currently displayed function. Reset ALL will • Compass/Temperature/Audio be displayed during this three-second window. • Average Fuel Economy Compass/Temperature/Audio • Distance To Empty (DTE) Press and release the COMPASS button to display one of •...
Page 237: Distance To Empty (Dte)
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Distance To Empty (DTE) Tire Pressure Monitor (TPM) Shows the estimated distance that can be traveled with Refer to “Starting And Operating”, “Tire Pressure Moni- the fuel remaining in the tank. This estimated distance is toring System (TPMS)”...
Page 238: Display Units Of Measure In
236 UNDERSTANDING YOUR INSTRUMENT PANEL Display Units of Measure in Use the SELECT button to display one of the following choices: To make your selection, press and release the SELECT button until “ENGLISH” or “METRIC” appears. Language When in this display you may select different languages Personal Settings (Customer-Programmable Features) for all display nomenclature, including the trip functions.
Page 239 UNDERSTANDING YOUR INSTRUMENT PANEL 237 Auto Lock Doors RKE Unlock When ON is selected, all doors lock automatically when When Driver’s Door 1st is selected only the driver’s door the speed of the vehicle reaches 15 mph (24 km/h). Press will unlock on the first press of the Remote Keyless Entry and hold the SELECT button when in this display until (RKE) transmitter UNLOCK button and require a second...
Page 240 238 UNDERSTANDING YOUR INSTRUMENT PANEL Sound Horn with Lock Key Off Power Delay When ON is selected, a short horn sound will occur when When this feature is selected the power window the RKE transmitter LOCK button is pressed. This feature switches, radio, Uconnect®...
Page 241 UNDERSTANDING YOUR INSTRUMENT PANEL 239 Hill Start Assist (HSA) — If Equipped Automatic Compass Calibration When on is selected, the HSA system is active. Refer to This compass is self-calibrating, which eliminates the “Electronic Brake Control System” in “Starting And Oper- need to set the compass manually.
Page 242 240 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Compass Calibration 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the If the compass appears erratic and the “CAL” indicator “CAL” indicator turns off. The compass will now does not appear in the EVIC display, you must put the function normally.
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 241 1. Turn the ignition switch ON. 2. Press and hold the COMPASS button for approxi- mately two seconds. 3. Press the DOWN button until “Compass Variance” message and the last variance zone number displays in the EVIC. 4.
Page 244: Understanding Your Instrument Panel Uconnect® 230 - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)
242 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® 230 — AM/FM STEREO RADIO AND Operating Instructions - Radio Mode 6-DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio.
Page 245 UNDERSTANDING YOUR INSTRUMENT PANEL 243 SEEK Buttons Voice Command Button Uconnect® Phone — If Equipped Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch Press this button to operate the Uconnect® Phone feature to seek up and the left switch to seek down.
Page 246 244 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry. Once in this Press the TIME button to alternate locations of the time display follow the above procedure, starting at step 2. and frequency display.
Page 247 UNDERSTANDING YOUR INSTRUMENT PANEL 245 Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display.
Page 248 246 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following 16-Digit Character Program Type format types: Display Oldies Oldies 16-Digit Character Program Type Personality Persnlty Display Public Public No program type or None undefined Rhythm and Blues R &...
Page 249 UNDERSTANDING YOUR INSTRUMENT PANEL 247 • DISC Play/Pause - By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency You can toggle between playing the DVD and station with the same selected Music Type name. The pausing the DVD by pushing the SELECT Music Type function only operates when in the FM mode.
Page 250 248 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save • The available selections for each of the above entries changes. varies depending upon the disc. • Player Defaults - Selecting this item will allow the •...
Page 251 UNDERSTANDING YOUR INSTRUMENT PANEL 249 Audio Language — If Equipped Subtitles — If Equipped Selecting this item allows you to choose a default audio Selecting this item allows you to choose between subtitle language (effective only if the language is supported by Off or On.
Page 252 250 UNDERSTANDING YOUR INSTRUMENT PANEL AutoPlay — If Equipped The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station When this is set to On and a DVD video is inserted, it will and press and release that button.
Page 253: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Buttons 1 - 6 CAUTION! These buttons tune the radio to the stations that you The radio may shut down during extremely hot commit to pushbutton memory {12 AM, 12 FM, and conditions. When this occurs, the radio will indicate 12 Satellite (if equipped) stations}.
Page 254 252 UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show LOADING DISC when the disc Press and hold the EJECT button for five seconds and all is loading and “READING DISC” when the radio is CDs will be ejected from the radio. reading the disc.
Page 255 UNDERSTANDING YOUR INSTRUMENT PANEL 253 TIME Button (CD MODE) Supported Media (Disc Types) Press this button to change the display from a large CD The MP3/WMA file recording media supported by the playing time display to a small CD playing time display. radio are CDDA, CD-R, CD-RW, MP3,WMA, DVD Video, DVD-R, DVD-RW, DVD+R, DVD+RW, and CDDA+MP3.
Page 256 254 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: Supported MP3/WMA File Formats • Level 1: 12 (including a separator . and a three- The radio will recognize only files with the *.MP3/WMA character extension) extension as MP3/WMA files. Non-MP3/WMA files •...
Page 257 UNDERSTANDING YOUR INSTRUMENT PANEL 255 Playlist files are not supported. MP3 Pro files are not MPEG Sampling Fre- Bit Rate (kbps) supported. Specification quency (kHz) MPEG-1 Audio 48, 44.1, 32 320, 256, 224, Playback of MP3/WMA Files Layer 3 192, 160, 128, When a medium containing MP3/WMA data is loaded, 112, 96, 80, 64, the radio checks all files on the medium.
Page 258: List Button (Disc Mode For Mp3/Wma Play)
256 UNDERSTANDING YOUR INSTRUMENT PANEL To increase the speed of disc loading, it is recommended Press the INFO button once more to return to elapsed to use CD-R media and single-session discs. To create a time priority mode. single-session disc, enable the “Disc at Once” option Press and hold the INFO button for three seconds or before writing to the disc.
Page 259 UNDERSTANDING YOUR INSTRUMENT PANEL 257 SEEK Button (Auxiliary Mode) SET Button (Auxiliary Mode) No function. No function. SCAN Button (Auxiliary Mode) Operating Instructions — Voice Command System (If Equipped) No function. Refer to “Voice Command” for further details. EJECT Button (Auxiliary Mode) Operating Instructions - Uconnect®...
Page 260 258 UNDERSTANDING YOUR INSTRUMENT PANEL Dolby® Uconnect® (Satellite Radio) — If Equipped Manufactured under license from Dolby® Laboratories. Satellite radio uses direct satellite-to-receiver broadcast- Dolby® and the double-D symbol are trademarks of ing technology to provide clear digital sound, coast to Dolby®...
Page 261 UNDERSTANDING YOUR INSTRUMENT PANEL 259 information, call the toll-free number 888-539-7474, or selected. Press the TUNE/SCROLL control knob and the visit the Sirius web site at www.sirius.com, or at Sirius ID number will display. The Sirius ID number www.siriuscanada.ca for Canadian residents. display will time out in two minutes.
Page 262 260 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down.
Page 263 UNDERSTANDING YOUR INSTRUMENT PANEL 261 additional three seconds will make the radio display the Toggle the MUSIC TYPE button again to select the music Song Title all of the time (press and hold again to return type. to normal display). By pressing the SEEK button when the Music Type RW/FF function is active, the radio will be tuned to the next...
Page 264: Uconnect® 730N/430/430N Cd/Dvd/Hdd/Nav - If Equipped
262 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Every time a preset button is used, a corresponding Memory button number will display. When you are receiving a station that you wish to Buttons 1 - 6 commit to pushbutton memory, press the SET/RND These buttons tune the radio to the channels that you button.
Page 265: Uconnect® 130
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Uconnect® 130 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio.
Page 266 264 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes Press and release the SEEK buttons to search for the next will begin to blink. listenable station in AM/FM mode.
Page 267 UNDERSTANDING YOUR INSTRUMENT PANEL 265 Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display.
Page 268: Operation Instructions - Cd Mode For
266 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions — CD MODE For CD And repeating the above procedure with this exception: Press MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 269 UNDERSTANDING YOUR INSTRUMENT PANEL 267 If you insert a disc with the ignition ON and the radio CAUTION! (Continued) ON, the unit will switch from radio to CD mode and • Dual-media disc types (one side is a DVD, the begin to play when you insert the disc.
Page 270: Notes On Playing Mp3 Files
268 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button AM/FM Button Press the right SEEK button for the next selection on the Press the button to select either AM or FM mode. CD. Press the left SEEK button to return to the beginning SET/RND Button (Random Play Button) of the current selection, or return to the beginning of the Press this button while the CD is playing to activate...
Page 271 UNDERSTANDING YOUR INSTRUMENT PANEL 269 Supported Media (Disc Types) display the file name and folder name, and will assign a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Page 272 270 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Sampling Fre- Bit Rate (kbps) Specification quency (kHz) The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 MPEG-1 Audio 48, 44.1, 32 320, 256, 224, extension may cause playback problems.
Page 273: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Playback of MP3 Files Operation Instructions - Auxiliary Mode When a medium containing MP3 data is loaded, the The auxiliary (AUX) jack is an audio input jack, which radio checks all files on the medium. If the medium allows the user to plug in a portable device, such as an contains a lot of folders or files, the radio will take more MP3 player, or iPod®, and utilize the vehicle’s audio...
Page 274: Operating Instructions - Radio Mode
272 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® 130 WITH SATELLITE RADIO Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio.
Page 275 UNDERSTANDING YOUR INSTRUMENT PANEL 273 SEEK Buttons If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With Uconnect Press and release the SEEK buttons to search for the next Phone” message will display on the radio screen. listenable station in AM/FM mode.
Page 276 274 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above 1. Press and hold the TIME button until the hours blink. procedure, starting at Step 2. 2.
Page 277 UNDERSTANDING YOUR INSTRUMENT PANEL 275 Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display.
Page 278 276 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following 16-Digit Character Program Type format types: Display Oldies Oldies 16-Digit Character Program Type Personality Persnlty Display Public Public No program type or None undefined Rhythm and Blues R &...
Page 279 UNDERSTANDING YOUR INSTRUMENT PANEL 277 By pressing the SEEK button when the Music Type icon the minutes using the right side TUNE/SCROLL con- is displayed, the radio will be tuned to the next frequency trol knob. Press the TUNE/SCROLL control knob to station with the same selected Music Type name.
Page 280: Operation Instructions - Cd Mode For
278 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions — CD MODE for CD and repeating the above procedure with this exception: Press MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 281 UNDERSTANDING YOUR INSTRUMENT PANEL 279 If you insert a disc with the ignition ON and the radio CAUTION! (Continued) ON, the unit will switch from radio to CD mode and • Dual-media disc types (one side is a DVD, the begin to play when you insert the disc.
Page 282: Notes On Playing Mp3 Files
280 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button AM/FM Button Press the right SEEK button for the next selection on the Press the button to select either AM or FM mode. CD. Press the left SEEK button to return to the beginning SET/RND Button (Random Play Button) of the current selection, or return to the beginning of the Press this button while the CD is playing to activate...
Page 283 UNDERSTANDING YOUR INSTRUMENT PANEL 281 Supported Media (Disc Types) display the file name and folder name, and will assign a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Page 284 282 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Sampling Fre- Bit Rate (kbps) Specification quency (kHz) The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 MPEG-1 Audio 48, 44.1, 32 320, 256, 224, extension may cause playback problems.
Page 285: List Button (Cd Mode For Mp3 Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 283 Playback of MP3 Files LIST Button (CD Mode for MP3 Play) When a medium containing MP3 data is loaded, the Pressing the LIST button will bring up a list of all folders radio checks all files on the medium. If the medium on the disc.
Page 286: Uconnect® (Satellite Radio) - If Equipped
284 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds Uconnect® (Satellite Radio) — If Equipped to return to elapsed time display. Satellite radio uses direct satellite-to-receiver broadcast- Operation Instructions - Auxiliary Mode ing technology to provide clear digital sound, coast to coast.
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285 information, call the toll-free number 888-539-7474, or selected. Press the TUNE/SCROLL control knob and the visit the Sirius web site at www.sirius.com, or at Sirius ID number will display. The Sirius ID number www.siriuscanada.ca for Canadian residents. display will time out in two minutes.
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down.
Page 289 UNDERSTANDING YOUR INSTRUMENT PANEL 287 additional three seconds will make the radio display the Toggle the MUSIC TYPE button again to select the music Song Title all of the time (press and hold again to return type. to normal display). By pressing the SEEK button when the Music Type RW/FF function is active, the radio will be tuned to the next...
Page 290: Ipod®/Usb/Mp3 Control - If Equipped
288 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory Every time a preset button is used, a corresponding button number will display. When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. Buttons 1 - 6 The symbol SET 1 will now show in the display window.
Page 291: Connecting The Ipod® Or External Usb Device
UNDERSTANDING YOUR INSTRUMENT PANEL 289 iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Some iPod® software versions may not fully support the iPod® control features. Please visit Apple’s website for software updates. NOTE: • If the radio has a USB port, refer to the appropriate Uconnect®...
Page 292: Using This Feature
290 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the audio device battery is completely dis- Controlling The iPod® Or External USB Device charged, it may not communicate with the iPod®/USB/ Using Radio Buttons MP3 control system until a minimum charge is attained. To get into the iPod®/USB/MP3 control mode and Leaving the audio device connected to the iPod®/USB/ access a connected audio device, either press the “AUX”...
Page 293 UNDERSTANDING YOUR INSTRUMENT PANEL 291 • Turning it clockwise (forward) by one click, while • Use the << SEEK and SEEK>> buttons to jump to the playing a track, skips to the next track or press the previous or next track. Pressing the SEEK>> button VR button and say Next Track .
Page 294: List Or Browse Mode
292 UNDERSTANDING YOUR INSTRUMENT PANEL • Press the SCAN button to use iPod®/USB/MP3 de- List Or Browse Mode vice scan mode, which will play the first 10 seconds of During Play mode, pressing any of the buttons described each track in the current list and then forward to the below, will bring up List mode.
Page 295 UNDERSTANDING YOUR INSTRUMENT PANEL 293 • During all List modes, the iPod® displays all lists in • To exit List mode without selecting a track, press the “wrap-around” mode. So if the track is at the bottom same PRESET button again to go back to Play mode. of the list, just turn the wheel backward (counter- •...
Page 296: Bluetooth Streaming Audio (Btsa)
294 UNDERSTANDING YOUR INSTRUMENT PANEL Bluetooth Streaming Audio (BTSA) CAUTION! Music can be streamed from your cellular phone to the • Leaving the iPod® or external USB device (or any Uconnect® phone system. supported device) anywhere in the vehicle in ex- Controlling BTSA Using Radio Buttons treme heat or cold can alter the operation or dam- age the device.
Page 297 UNDERSTANDING YOUR INSTRUMENT PANEL 295 Selecting A Different Audio Device Previous Track Use the SEEK DOWN button, or press the VR button on 1. Press the PHONE button to begin. the radio and say “Previous Track”, to jump to the 2.
Page 298: Steering Wheel Audio Controls
296 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and The remote sound system controls are located on the rear mode of the sound system. Pressing the top of the rocker surface of the steering wheel.
Page 299: Radio Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 297 Radio Operation If you press the switch up or down twice, it plays the second track; three times, it will play the third, etc. Pressing the top of the switch will “Seek” up for the next listenable station and pressing the bottom of the switch The center button on the left side rocker switch has no will “Seek”...
Page 300: Cd/Dvd Disc Maintenance
298 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD DISC MAINTENANCE NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e., scratched, reflective coating To keep a CD/DVD in good condition, take the following removed, a hair, moisture or dew on the disc) oversized, precautions: or have protection encoding.
Page 301: Climate Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 299 CLIMATE CONTROLS The Manual Temperature Controls consist of a series of outer rotary dials and inner push knobs. The air conditioning and heating system is designed to make you comfortable in all types of weather. Blower Control Manual Heating And Air Conditioning Rotate this control to regulate the...
Page 302 300 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Mode Control (Air Direction) Rotate this control to choose from sev- Rotate this control to regulate the tem- eral patterns of air distribution. You perature of the air inside the passenger can select either a primary mode as compartment.
Page 303 UNDERSTANDING YOUR INSTRUMENT PANEL 301 • Bi-Level windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Air is directed through the panel and floor outlets. • Defrost NOTE: For all settings, except full cold or full hot, there Air is directed through the windshield and side is a difference in temperature between the upper and window demist outlets.
Page 304 302 UNDERSTANDING YOUR INSTRUMENT PANEL • Recirculation Control • The A/C will engage automatically to prevent fogging when the recirculation button is pressed and the mode Pressing the Recirculation Control button will control is set to panel or panel / floor. put the system in recirculation mode.
Page 305: Automatic Temperature Control (Atc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 303 NOTE: The air conditioning compressor will not engage Automatic Temperature Control (ATC) — until the engine has been running for about 10 seconds. If Equipped • MAX A/C The Automatic Temperature Control system automati- cally maintains the climate in the cabin of the vehicle at For maximum cooling use the A/C and recirculation the comfort levels desired by the driver and passenger.
Page 306 304 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Operation You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting Operation of the system is quite simple. the “O” (OFF) position on the blower control stops the 1. Turn the Mode Control knob (on the right) and the system completely and closes the outside air intake.
Page 307 UNDERSTANDING YOUR INSTRUMENT PANEL 305 • If your air conditioning performance seems lower than Manual Operation expected, check the front of the A/C condenser located This system offers a full complement of manual override in front of the radiator for an accumulation of dirt or features, which consist of Blower Preferred Automatic, insects.
Page 308 306 UNDERSTANDING YOUR INSTRUMENT PANEL...
Page 309 UNDERSTANDING YOUR INSTRUMENT PANEL 307 • Floor The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and •...
Page 310 308 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control NOTE: • When the ignition switch is turned to the LOCK Press this button to turn on the air conditioning during manual operation position, the recirculation feature will be cancelled. only. When the air conditioning is •...
Page 311: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 309 • Most of the time, when in Automatic Operation, you Operating Tips can temporarily put the system into Recirculation NOTE: Refer to the chart at the end of this section for Mode by pressing the Recirculation button. However, suggested control settings for various weather condi- under certain conditions, while in Automatic Mode, tions.
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL Winter Operation Window Fogging Use of the air Recirculation Mode during winter months Interior fogging on the windshield can be quickly re- is not recommended because it may cause window moved by turning the mode selector to Defrost. The fogging.
Page 313 UNDERSTANDING YOUR INSTRUMENT PANEL 311 Side Window Demisters A/C Air Filter — If Equipped A side window demister outlet is located at each end of The A/C Filter prevents most dust and pollen from enter- the instrument panel. These non-adjustable outlets direct ing the cabin.
Page 314 312 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
Page 315: Starting And Operating
STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....317 MANUAL TRANSMISSION — IF EQUIPPED . . .320 ▫ Manual Transmission – If Equipped ..317 ▫...
Page 316 314 STARTING AND OPERATING ▫ Brake Assist System (BAS) ....343 AUTOSTICK® ......330 ▫...
Page 317 STARTING AND OPERATING 315 ▫ Tire Spinning ......369 TIRES — GENERAL INFORMATION..362 ▫...
Page 318 316 STARTING AND OPERATING ▫ Reformulated Gasoline ....385 TRAILER TOWING .....393 ▫...
Page 319: Starting Procedures
STARTING AND OPERATING 317 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both • Do not leave the key fob in or near the vehicle, or inside and outside mirrors, and fasten your seat belts. in a location accessible to children. A child could operate power windows, other controls, or move WARNING! the vehicle.
Page 320: Automatic Transmission - If Equipped
318 STARTING AND OPERATING Automatic Transmission – If Equipped Normal Starting The shift lever must be in the PARK or NEUTRAL Normal starting of either a cold or a warm engine does position before you can start the engine. Apply the brakes not require pumping or pressing the accelerator pedal.
Page 321: Extreme Cold Weather
STARTING AND OPERATING 319 in the ON position, release the accelerator pedal and WARNING! (Continued) repeat the “Normal Starting” procedure. another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. WARNING! Refer to “Jump Starting” in “What To Do In Emer- Never pour fuel or other flammable liquid into the gencies”...
Page 322: Engine Block Heater - If Equipped
320 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED MANUAL TRANSMISSION — IF EQUIPPED The engine block heater warms the engine, and permits Five–Speed Manual Transmission quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a WARNING! grounded, three-wire extension cord.
Page 323 STARTING AND OPERATING 321 CAUTION! • Launching in any gear except 1st gear will result in excessive slipping of the clutch and potentially lugging or stalling the engine. • Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position.
Page 324: Recommended Shift Speeds
322 STARTING AND OPERATING Never shift into REVERSE until the vehicle has come to a Downshifting complete stop. Proper downshifting will improve fuel economy and pro- long engine life. NOTE: During cold weather, until the transmission lubri- cant is warm, you may experience slightly higher shift CAUTION! efforts.
Page 325: Automatic Transmission
STARTING AND OPERATING 323 AUTOMATIC TRANSMISSION — IF EQUIPPED WARNING! • Unintended movement of a vehicle could injure CAUTION! those in or near the vehicle. As with all vehicles, Damage to the transmission may occur if the follow- you should never exit a vehicle while the engine is ing precautions are not observed: running.
Page 326: Key Ignition Park Interlock
324 STARTING AND OPERATING Key Ignition Park Interlock WARNING! (Continued) This vehicle is equipped with a Key Ignition Park Inter- • Allowing children to be in a vehicle unattended is lock which requires the shift lever to be in PARK before dangerous for a number of reasons.
Page 327: Continuously Variable Automatic Transmission (Cvt)
STARTING AND OPERATING 325 out of PARK, the ignition switch must be turned to the Only shift from DRIVE to PARK or REVERSE when the ON/RUN position (engine running or not) and the brake accelerator pedal is released and the vehicle is stopped. pedal must be pressed.
Page 328 326 STARTING AND OPERATING NOTE: After selecting any gear range, wait a moment to PARK allow the selected gear to engage before accelerating. This range supplements the parking brake by locking the This is especially important when the engine is cold. transmission.
Page 329 STARTING AND OPERATING 327 WARNING! WARNING! (Continued) • Unintended movement of a vehicle could injure • Never use the PARK position as a substitute for the those in or near the vehicle. As with all vehicles, parking brake. Always apply the parking brake you should never exit a vehicle while the engine is fully when parked to guard against vehicle move- running.
Page 330 328 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • Allowing children to be in a vehicle unattended is • DO NOT race the engine when shifting from dangerous for a number of reasons. A child or PARK or NEUTRAL into another gear range, as this others could be seriously or fatally injured.
Page 331 STARTING AND OPERATING 329 REVERSE CAUTION! This range is for moving the vehicle backward. Shift into Towing the vehicle, coasting, or driving for any other REVERSE only after the vehicle has come to a complete reason with the transmission in NEUTRAL can cause stop.
Page 332: Autostick
330 STARTING AND OPERATING control (refer to AutoStick® in this section) to select a LOW – IF EQUIPPED lower gear ratio. Under these conditions, using a lower This range should be used for engine braking when gear ratio will improve performance and extend trans- descending very steep grades.
Page 333: Operation
STARTING AND OPERATING 331 Operation condition would result. It will remain in the selected gear until another upshift or downshift is chosen, except as NOTE: AutoStick® is not available until the CVT warms described below: up in cold weather. • The transmission will automatically downshift to first When the shift lever is in the DRIVE position, AutoStick®...
Page 334: Four-Wheel Drive Operation - If Equipped
332 STARTING AND OPERATING • If the system detects powertrain overheating, the FOUR-WHEEL DRIVE OPERATION — transmission will revert to the automatic shift mode IF EQUIPPED and remain in that mode until the powertrain cools off. This feature provides full time, on-demand, four–wheel •...
Page 335: On-Road Driving Tips
STARTING AND OPERATING 333 Where one or more wheels have wheel spin or if addi- ON-ROAD DRIVING TIPS tional traction is needed in sand, deep snow, or loose Utility vehicles have higher ground clearance and a traction surfaces, activate the “4WD LOCK” switch by narrower track to make them capable of performing in a pulling up once and releasing.
Page 336: Power Steering
334 STARTING AND OPERATING POWER STEERING This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it The standard power steering system will give you good does not in any way damage the steering system. vehicle response and increased ease of maneuverability in tight spaces.
Page 337: Power Steering Fluid Check
STARTING AND OPERATING 335 Power Steering Fluid Check WARNING! Checking the power steering fluid level at a defined Fluid level should be checked on a level surface and service interval is not required. The fluid should only be with the engine off to prevent injury from moving checked if a leak is suspected, abnormal noises are parts and to ensure accurate fluid level reading.
Page 338: Parking Brake
336 STARTING AND OPERATING PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible.
Page 339 STARTING AND OPERATING 337 NOTE: WARNING! • When the parking brake is applied and the automatic • When leaving the vehicle, always remove the key transmission is placed in gear, the “Brake Warning fob from the ignition and lock your vehicle. Light”...
Page 340: Brake System
338 STARTING AND OPERATING BRAKE SYSTEM WARNING! (Continued) Your vehicle is equipped with power assisted brakes as • Always fully apply the parking brake when leav- standard equipment. In the event power assist is lost for ing your vehicle or it may roll and cause damage or any reason (for example, repeated brake applications injury.
Page 341: Anti-Lock Brake System (Abs)
STARTING AND OPERATING 339 If either of the two hydraulic systems lose normal capa- Anti-Lock Brake System (ABS) bility, the remaining system will still function with some The ABS provides increased vehicle stability and brake loss of overall braking effectiveness. This will be evident performance under most braking conditions.
Page 342 340 STARTING AND OPERATING required. However, the conventional brake system will WARNING! (Continued) continue to operate normally if the “Brake Warning • The ABS cannot prevent collisions, including those Light” is not on. resulting from excessive speed in turns, following If the “ABS Warning Light”...
Page 343 STARTING AND OPERATING 341 ABS is activated during braking under certain road or WARNING! stopping conditions. ABS-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose The Anti-Lock Brake System (ABS) contains sophis- debris, or panic stops. ticated electronic equipment that may be susceptible to interference caused by improperly installed or You may also experience the following when the brake high output radio transmitting equipment.
Page 344: Electronic Brake Control System
342 STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM Traction Control System (TCS) Your vehicle may be equipped with an optional ad- This system monitors the amount of wheel spin of each of vanced electronic brake control system that includes the driven wheels. If wheel spin is detected, brake Anti-Lock Brake System (ABS), Traction Control System pressure is applied to the slipping wheel(s) and engine (TCS), Brake Assist System (BAS), Electronic Roll Mitiga-...
Page 345: Brake Assist System (Bas)
STARTING AND OPERATING 343 Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking • The Brake Assist System (BAS) cannot prevent the capability during emergency braking maneuvers. The natural laws of physics from acting on the vehicle, system detects an emergency braking situation by sens- nor can it increase the traction afforded by prevail- ing the rate and amount of brake application and then...
Page 346: Electronic Roll Mitigation (Erm)
344 STARTING AND OPERATING Electronic Roll Mitigation (ERM) NOTE: Anytime the ESC system is in the “Full Off” mode, ERM is disabled. Refer to “Electronic Stability This system anticipates the potential for wheel lift by Control (ESC)” in this section for a complete explanation monitoring the driver’s steering wheel input and the of the available ESC modes.
Page 347: Hill Descent Control (Hdc) - If Equipped
STARTING AND OPERATING 345 Hill Descent Control (HDC) – If Equipped HDC operation can be overridden with brake application to slow the vehicle down below the HDC control speed. This system maintains vehicle speed while descending Conversely, if more speed is desired during HDC control, hills during off-road driving situations.
Page 348: Hill Start Assist (Hsa) - Manual Transmission Only
346 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., Hill Start Assist (HSA) – Manual Transmission Only vehicle facing uphill is in forward gear; vehicle back- ing uphill is in REVERSE gear). The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill.
Page 349 STARTING AND OPERATING 347 For vehicles not equipped with the EVIC, perform the 7. Press the “ESC Off” switch (located in the lower following steps: switch bank below the climate controls) four times within 20 seconds. The “ESC Activation/Malfunction NOTE: You must complete Steps 1 through 8 within Indicator Light”...
Page 350: Electronic Stability Control (Esc)
348 STARTING AND OPERATING Electronic Stability Control (ESC) WARNING! This system enhances directional control and stability of • The Electronic Stability Control (ESC) cannot pre- the vehicle under various driving conditions. ESC cor- vent the natural laws of physics from acting on the rects for over-steering or under-steering of the vehicle by vehicle, nor can it increase the traction afforded by applying the brake of the appropriate wheel to assist in...
Page 351 STARTING AND OPERATING 349 ESC Operating Modes Activation/Malfunction Indicator Light” will be illumi- nated. All other stability features of ESC function nor- The ESC system has three available operating modes for mally. This mode is intended to be used if the vehicle is four–wheel drive equipped vehicles and two available in deep snow, sand or gravel conditions and more wheel operating modes for two–wheel drive equipped vehicles.
Page 352 350 STARTING AND OPERATING OFF” message will appear in the odometer. Press and WARNING! release the Trip Odometer button located on the instru- ment cluster to clear this message. When in “Partial Off” mode, the TCS functionality of ESC (except for the limited slip feature described in In this mode, ESC and TCS, except for the “limited slip”...
Page 353: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
STARTING AND OPERATING 351 To turn ESC on again, momentarily press the “ESC Off” ESC Activation/Malfunction Indicator Light And switch. This will restore the “ESC On” mode of operation. ESC OFF Indicator Light The “ESC Activation/Malfunction Indicator NOTE: The “ESC OFF” message will display and an Light”...
Page 354: Tire Safety Information
352 STARTING AND OPERATING Malfunction Indicator Light” begins to flash during ac- TIRE SAFETY INFORMATION celeration, ease up on the accelerator and apply as little Tire Markings throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. NOTE: •...
Page 355 STARTING AND OPERATING 353 • Temporary spare tires are spares designed for tempo- NOTE: rary emergency use only. Temporary high pressure • P (Passenger) - Metric tire sizing is based on U.S. compact spare tires have the letter “T” or “S” molded design standards.
Page 356 354 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 357 STARTING AND OPERATING 355 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 358: Tire Identification Number (Tin)
356 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire, the outboard side, then you will find it on the inboard however, the date code may only be on one side.
Page 359: Tire Terminology And Definitions
STARTING AND OPERATING 357 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 360: Tire Loading And Tire Pressure
358 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
Page 361 STARTING AND OPERATING 359 To determine the maximum loading conditions of your 3) tire size designed for your vehicle vehicle, locate the statement “The combined weight of 4) cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX lbs or spare tires.
Page 362 360 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • The following table shows examples on how to calcu- “XXX” amount equals 1,400 lbs (635 kg) and there will late total load, cargo/luggage, and towing capacities be five 150 lb (68 kg) passengers in your vehicle, the of your vehicle with varying seating configurations...
Page 363 STARTING AND OPERATING 361...
Page 364: Tires - General Information
362 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 365: Tire Inflation Pressures
STARTING AND OPERATING 363 stability of the vehicle and can produce a feeling of WARNING! (Continued) sluggish response or over responsiveness in the steering. • Unequal tire pressures from one side of the vehicle Unequal tire pressures can cause erratic and unpredict- to the other can cause the vehicle to drift to the able steering response.
Page 366 364 STARTING AND OPERATING Check tire pressures more often if subject to a wide range CAUTION! of outdoor temperatures, as tire pressures vary with temperature changes. After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent Tire pressures change by approximately 1 psi (7 kPa) per moisture and dirt from entering the valve stem, 12°F (7°C) of air temperature change.
Page 367: Tire Pressures For High Speed Operation
STARTING AND OPERATING 365 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires on speeds, maintaining correct tire inflation pressure is very your vehicle will cause your vehicle to handle poorly.
Page 368: Summer Or Three Season Tires - If Equipped
366 STARTING AND OPERATING the tire sidewall. Use all season tires only in sets of four; If you need snow tires, select tires equivalent in size and failure to do so may adversely affect the safety and type to the original equipment tires. Use snow tires only handling of your vehicle.
Page 369: Spare Tire Matching Original Equipped Tire And Wheel - If Equipped
STARTING AND OPERATING 367 Spare Tire Matching Original Equipped Tire And CAUTION! Wheel – If Equipped Because of the reduced ground clearance, do not take Your vehicle may be equipped with a spare tire and your vehicle through an automatic car wash with a wheel equivalent in look and function to the original compact, full size or limited-use temporary spare equipment tire and wheel found on the front or rear axle...
Page 370: Full Size Spare - If Equipped
368 STARTING AND OPERATING Since this tire has limited tread life the original equip- Full Size Spare – If Equipped ment tire should be repaired (or replaced) and reinstalled The full size spare is for temporary emergency use only. on your vehicle at the first opportunity. This tire may look like the original equipped tire on the Do not install a wheel cover or attempt to mount a front or rear axle of your vehicle, but it is not.
Page 371: Tire Spinning
STARTING AND OPERATING 369 tire affects vehicle handling. Since it is not the same as Tire Spinning your original equipment tire, replace (or repair) the When stuck in mud, sand, snow, or ice conditions, do not original equipment tire and reinstall on the vehicle at the spin your vehicle’s wheels above 30 mph (48 km/h) or first opportunity.
Page 372: Tread Wear Indicators
370 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth Tread wear indicators are in the original equipment tires becomes 1/16 in (2 mm). When the tread is worn to the to help you in determining when your tires should be tread wear indicators, the tire should be replaced.
Page 373: Replacement Tires
STARTING AND OPERATING 371 “Tread Wear Indicators”). Refer to the “Tire and Loading WARNING! Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be Tires and the spare tire should be replaced after six found on the original equipment tire sidewall.
Page 374 372 STARTING AND OPERATING WARNING! WARNING! (Continued) • Never use a tire with a smaller load index or • Do not use a tire, wheel size or rating other than capacity, other than what was originally equipped that specified for your vehicle. Some combinations on your vehicle.
Page 375: Tire Chains (Traction Devices)
STARTING AND OPERATING 373 TIRE CHAINS (TRACTION DEVICES) These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with Due to limited clearance, tire chains or traction devices aggressive tread designs such as those on all season type are not recommended.
Page 376: Tire Pressure Monitoring System (Tpms)
374 STARTING AND OPERATING The suggested rotation method is the “rearward cross” TIRE PRESSURE MONITORING SYSTEM (TPMS) shown in the following diagram. This rotation pattern The Tire Pressure Monitor System (TPMS) will warn the does not apply to some directional tires that must not be driver of a low tire pressure based on the vehicle recom- reversed.
Page 377 STARTING AND OPERATING 375 also increase as the vehicle is driven - this is normal updated tire pressures. The vehicle may need to be and there should be no adjustment for this increased driven for up to 20 minutes above 15 mph (24 km/h) in pressure.
Page 378 376 STARTING AND OPERATING NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance or to provide warning of a tire failure equipment tires and wheels. TPMS pressures and or condition.
Page 379: Base System
STARTING AND OPERATING 377 • Seasonal temperature changes will affect tire pressure, • Four Tire Pressure Monitoring Sensors and the TPMS will monitor the actual tire pressure in • Tire Pressure Monitoring Telltale Light the tire. Tire Pressure Monitoring Low Pressure Warnings Base System The Tire Pressure Monitoring Telltale Light will illumi- This is the TPMS warning indicator located in the...
Page 380 378 STARTING AND OPERATING Check TPMS Warnings 4. Using tire chains on the vehicle. The Tire Pressure Monitoring Telltale Light will flash on 5. Using wheels/tires not equipped with TPM sensors. and off for 75 seconds and remain on solid when a system NOTE: Your vehicle is equipped with a compact spare fault is detected.
Page 381: Premium System - If Equipped
STARTING AND OPERATING 379 3. However, after driving the vehicle for up to 20 minutes Premium System – If Equipped above 15 mph (24 km/h), the Tire Pressure Monitoring The TPMS uses wireless technology with wheel rim Telltale Light will flash on and off for 75 seconds and mounted electronic sensors to monitor tire pressure levels.
Page 382 380 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illumi- nate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire pressures are low.
Page 383 STARTING AND OPERATING 381 “LOW TIRE” text message will no longer be displayed, the graphic display of the pressure value(s) will stop flashing, and the Tire Pressure Monitoring Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information.
Page 384 382 STARTING AND OPERATING text message will not be present, and a pressure value The EVIC will also display a SERVICE TPM SYSTEM will be displayed instead of dashes. A system fault can message for a minimum of five seconds when a system occur with any of the following scenarios: fault related to an incorrect sensor location fault is detected.
Page 385 STARTING AND OPERATING 383 2. If you install the compact spare tire in place of a road 4. For each subsequent ignition key cycle, a chime will tire that has a pressure below the low-pressure warn- sound and the Tire Pressure Monitoring Telltale Light ing limit, upon the next ignition key cycle, a chime will will flash on and off for 75 seconds and then remain on sound and the Tire Pressure Monitoring Telltale Light...
Page 386: General Information
384 STARTING AND OPERATING General Information FUEL REQUIREMENTS This device complies with Part 15 of the FCC rules and 2.0L And 2.4L Engine RSS 210 of Industry Canada. Operation is subject to the This engine is designed to meet all emis- following conditions: sions regulations and provide excellent fuel •...
Page 387: Reformulated Gasoline
STARTING AND OPERATING 385 Over 40 auto manufacturers worldwide have issued and Gasoline/Oxygenate Blends endorsed consistent gasoline specifications (the World- Some fuel suppliers blend unleaded gasoline with oxy- wide Fuel Charter, WWFC) which define fuel properties genates such as Ethanol. Fuels blended with oxygenates necessary to deliver enhanced emissions, performance, may be used in your vehicle.
Page 388: E-85 Usage In Non-Flex Fuel Vehicles
386 STARTING AND OPERATING • disconnect and reconnect the battery to reset the E-85 Usage In Non-Flex Fuel Vehicles engine controller memory Non-FFV vehicles are compatible with gasoline contain- ing 10% ethanol (E10). Gasoline with higher ethanol More extensive repairs will be required for prolonged content may void the vehicle’s warranty.
Page 389: Materials Added To Fuel
STARTING AND OPERATING 387 Materials Added To Fuel CAUTION! (Continued) All gasoline sold in the United States is required to • An out-of-tune engine or certain fuel or ignition contain effective detergent additives. Use of additional malfunctions can cause the catalytic converter to detergents or other additives is not needed under normal overheat.
Page 390: Carbon Monoxide Warnings
388 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper main- WARNING! tenance. Have the exhaust system inspected every Carbon monoxide (CO) in exhaust gases is deadly. time the vehicle is raised. Have any abnormal Follow the precautions below to prevent carbon conditions repaired promptly.
Page 391 STARTING AND OPERATING 389 After removing the gas cap, place the gas cap tether cable CAUTION! over a hook on the inside of the fuel door. This keeps the • Damage to the fuel system or emission control gas cap suspended away from and protects the vehicle’s system could result from using an improper fuel surface.
Page 392: Loose Fuel Filler Cap Message
390 STARTING AND OPERATING Loose Fuel Filler Cap Message WARNING! (Continued) If the vehicle diagnostic system determines that the fuel • Never add fuel when the engine is running. This is filler cap is loose or improperly installed, a “gASCAP” in violation of most state and federal fire regula- message will be displayed in the Odometer/Trip Odom- tions and may cause the MIL to turn on.
Page 393: Vehicle Certification Label
STARTING AND OPERATING 391 Vehicle Certification Label Gross Vehicle Weight Rating (GVWR) Your vehicle has a Vehicle Certification Label attached to The GVWR is the total allowable weight of your vehicle. the driver’s door B-Pillar. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the The label contains the following information: GVWR.
Page 394 392 STARTING AND OPERATING Curb Weight Overloading can cause potential safety hazards and shorten useful service life. Heavier suspension compo- The curb weight of a vehicle is defined as the total weight nents do not necessarily increase the vehicle’s GVWR. of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo Loading...
Page 395: Trailer Towing
STARTING AND OPERATING 393 TRAILER TOWING exceed the GVWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for In this section you will find safety tips and information further information. on limits to the type of towing you can reasonably do with your vehicle.
Page 396 394 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Tongue Weight (TW) The GAWR is the maximum capacity of the front and rear The tongue weight is the downward force exerted on the axles. Distribute the load over the front and rear axles hitch ball by the trailer.
Page 397 STARTING AND OPERATING 395 Weight-Carrying Hitch also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability. A weight-carrying hitch supports the trailer tongue Trailer sway control and a weight distributing (load weight, just as if it were luggage located at a hitch ball equalizing) hitch are recommended for heavier Tongue or some other connecting point of the vehicle.
Page 398: Trailer Hitch Classification
396 STARTING AND OPERATING Trailer Hitch Classification Trailer Hitch Classification Definitions The following chart provides the industry standard for Class Max. Trailer Hitch the maximum trailer weight a given trailer hitch class can Industry Standards tow and should be used to assist you in selecting the Class IV - Extra Heavy Duty 10,000 lbs (4 540 kg) correct trailer hitch for your intended towing condition.
Page 399: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 397 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum GTW Maximum Tongue Wt. Engine/Transmission Frontal Area (Gross Trailer Wt.) (See Note) 2.0L Auto/Man 22 sq ft (2.04 sq m) 1,000 lbs (450 kg) 150 lbs (50 kg)
Page 400 398 STARTING AND OPERATING which will cause loss of control of the vehicle and trailer. Consider the following items when computing the Failure to load trailers heavier in front is the cause of weight on the rear axle of the vehicle: many trailer collisions.
Page 401: Towing Requirements
STARTING AND OPERATING 399 Towing Requirements WARNING! To promote proper break-in of your vehicle drivetrain Improper towing can lead to a collision. Follow these components, the following guidelines are recommended: guidelines to make your trailer towing as safe as possible: CAUTION! •...
Page 402 400 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Safety chains must always be used between your • Total weight must be distributed between the tow vehicle and trailer. Always connect the chains to vehicle and the trailer such that the following four the frame or hook retainers of the vehicle hitch.
Page 403 STARTING AND OPERATING 401 Towing Requirements – Tires replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s • Do not attempt to tow a trailer while using a compact GVWR and GAWR limits. spare tire. Towing Requirements –...
Page 404 402 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Towing any trailer will increase your stopping If the trailer weighs more than 1,000 lbs (454 kg) distance. When towing you should allow for addi- loaded, it should have its own brakes and they tional space between your vehicle and the vehicle should be of adequate capacity.
Page 405 STARTING AND OPERATING 403 The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Seven-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 —...
Page 406: Towing Tips
404 STARTING AND OPERATING Towing Tips NOTE: Using a lower gear ratio while operating the vehicle under heavy loading conditions, will improve Before setting out on a trip, practice turning, stopping, performance and extend transmission life by reducing and backing up the trailer in an area located away from excessive shifting and heat buildup.
Page 407 STARTING AND OPERATING 405 To prevent excess heat generation, avoid continuous Cooling System driving at high RPM. Reduce vehicle speed as necessary To reduce potential for engine and transmission over- to avoid extended driving at high RPM. Return to a heating, take the following actions: higher gear or vehicle speed when grade and road City Driving...
Page 408: Recreational Towing (Behind Motorhome, Etc.)
406 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground Manual Transmission Automatic Transmission • Transmission in NEUTRAL Flat Tow None NOT ALLOWED • Key in ACC Position Dolly Tow Front OK (FWD Only) OK (FWD Only)
Page 409: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS HAZARD WARNING FLASHERS ...408 JUMP-STARTING PROCEDURES... .422 ▫ Preparations For Jump-Start ....422 IF YOUR ENGINE OVERHEATS .
Page 410: Hazard Warning Flashers
408 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel below the climate controls. potential for overheating by taking the appropriate action. •...
Page 411: Automatic Transmission Overheating
WHAT TO DO IN EMERGENCIES 409 CAUTION! WARNING! (Continued) do not open the hood until the radiator has had time Driving with a hot cooling system could damage to cool. Never try to open a cooling system pressure your vehicle. If the pointer rises to the H (red) mark, cap when the radiator or coolant bottle is hot.
Page 412: Jacking And Tire Changing
410 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! (Continued) • Never start or run the engine while the vehicle is WARNING! on a jack. • Do not attempt to change a tire on the side of the •...
Page 413: Jack Location
WHAT TO DO IN EMERGENCIES 411 Jack Location Spare Tire Stowage The jack and jack-handle are stowed under the load floor The compact spare tire is stowed under the rear load floor in the cargo area. in the cargo area. Spare Tire Removal Lift up the load floor cover and remove the hold down.
Page 414: Jacking Instructions
412 WHAT TO DO IN EMERGENCIES 2. Turn on the Hazard Warning flasher. Jacking Instructions 3. Set the parking brake. WARNING! 4. Place the shift lever in PARK (automatic transmission) Carefully follow these tire changing warnings to or REVERSE (manual transmission). help prevent personal injury or damage to your 5.
Page 415 WHAT TO DO IN EMERGENCIES 413 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to Jack Warning Label a service center where it can be raised on a lift.
Page 416 414 WHAT TO DO IN EMERGENCIES NOTE: Refer to “Tires — General Information” in “Start- ing And Operating” for further information about the spare tire, it’s use, and operation. 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench and remove the wrench from the jack assembly.
Page 417 WHAT TO DO IN EMERGENCIES 415 NOTE: There are front and rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts on one of the flanges in the sill flange assembly. The rear location is the same but with two rectangular cutouts.
Page 418 416 WHAT TO DO IN EMERGENCIES Front Jacking Location Rear Jacking Location Do not raise the vehicle until you are sure the jack is securely engaged.
Page 419 WHAT TO DO IN EMERGENCIES 417 3. Turn the jack screw to the left until the jack can be 5. Remove the wheel nuts and pull the wheel and wheel placed under the jacking location. Once the jack is covers, where applicable, off the hub. Install the spare positioned, turn the jack screw to the right until the wheel and wheel nuts with the cone shaped end of the jack head is properly engaged with the lift area closest...
Page 420 418 WHAT TO DO IN EMERGENCIES WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. NOTE: The wheel cover is held on the wheel by the wheel nuts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the wheel cover onto the wheel, then install the wheel nuts.
Page 421: Road Tire Installation
WHAT TO DO IN EMERGENCIES 419 8. Remove the wheel blocks and lower the jack until WARNING! it is free. Release the parking brake. Reassemble the lug wrench to the jack assembly and stow it in the spare tire A loose tire thrown forward in a collision or hard stop area.
Page 422 420 WHAT TO DO IN EMERGENCIES 3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered.
Page 423 WHAT TO DO IN EMERGENCIES 421 about the correct tightness, have them checked with a 3. Lower the vehicle to the ground by turning the jack torque wrench by your authorized dealer or service handle counterclockwise. station. 4. Finish tightening the lug nuts. Push down on the 6.
Page 424: Jump-Starting Procedures
422 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES WARNING! If your vehicle has a discharged battery it can be jump- Do not attempt jump-starting if the battery is frozen. started using a set of jumper cables and a battery in It could rupture or explode and cause personal injury.
Page 425 WHAT TO DO IN EMERGENCIES 423 Air Intake Finger Screws Positive Battery Post...
Page 426: Jump-Starting Procedure
424 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park WARNING! the vehicle within the jumper cables reach, set the • Take care to avoid the radiator cooling fan whenever parking brake and make sure the ignition is OFF. the hood is raised.
Page 427 WHAT TO DO IN EMERGENCIES 425 4. Connect the opposite end of the negative (-) jumper CAUTION! cable to a good engine ground (exposed metal part of the discharged vehicle’s engine) away from the battery Failure to follow these procedures could result in and the fuel injection system.
Page 428 426 WHAT TO DO IN EMERGENCIES Once the engine is started, remove the jumper cables in If frequent jump-starting is required to start your vehicle the reverse sequence: you should have the battery and charging system in- spected at your authorized dealer. 6.
Page 429: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 427 FREEING A STUCK VEHICLE CAUTION! (Continued) If your vehicle becomes stuck in mud, sand or snow, it can for at least one minute after every five rocking- often be moved using a rocking motion. Turn the steering motion cycles.
Page 430: Shift Lever Override
428 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! (Continued) • When “rocking” a stuck vehicle by shifting be- explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for tween DRIVE/2nd gear and REVERSE, do not spin longer than 30 seconds continuously without stop- the wheels faster than 15 mph (24 km/h), or drive- ping when you are stuck and do not let anyone near...
Page 431 WHAT TO DO IN EMERGENCIES 429 3. Using a small screwdriver or similar tool, remove the 4. Turn the ignition switch to the ACC or ON/RUN shift lever override access cover (located on the right position, but do not start the engine. side of the shifter housing).
Page 432: Towing A Disabled Vehicle
430 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing Condition Wheels OFF the Ground Manual Transmission Automatic Transmission • Transmission in NEUTRAL Flat Tow NONE NOT ALLOWED •...
Page 433: With Ignition Key
WHAT TO DO IN EMERGENCIES 431 With Ignition Key Manual Transmission • Front Wheel Drive (FWD) or Four-Wheel Drive (4WD) Automatic Transmission vehicles can be flat towed (all four wheels on the • Front Wheel Drive (FWD) vehicles can be towed with ground) with the transmission in NEUTRAL.
Page 434 432 WHAT TO DO IN EMERGENCIES All Transmissions Without The Ignition Key If you must use the accessories (wipers, defroster, etc.) Special care must be taken when the vehicle is towed while being towed, the key must be in the ON/RUN with the ignition in the LOCK/OFF position.
Page 435 MAINTAINING YOUR VEHICLE CONTENTS ▫ Engine Oil Filter ..... .444 ENGINE COMPARTMENT — 2.0L ..435 ▫...
Page 436 434 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission – If Equipped ..462 BULB REPLACEMENT ....478 ▫ Manual Transmission – If Equipped ..463 ▫...
Page 437: Engine Compartment - 2.0L
MAINTAINING YOUR VEHICLE 435 ENGINE COMPARTMENT — 2.0L 1 — Washer Fluid Reservoir 6 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 7 — Coolant Pressure Cap 3 — Engine Oil Fill 8 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 9 —...
Page 438: Engine Compartment - 2.4L
436 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.4L 1 — Washer Fluid Reservoir 6 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 7 — Coolant Pressure Cap 3 — Engine Oil Fill 8 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 9 —...
Page 439: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 437 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. the performance of the emissions, engine, and automatic It could also affect fuel economy and drivability.
Page 440: Emissions Inspection And Maintenance Programs
438 MAINTAINING YOUR VEHICLE the gas cap is properly tightened. Press the trip odometer Normally, the OBD II system will be ready. The OBD II RESET button to turn off the message. If the problem system may not be ready if your vehicle was recently persists, the message will appear the next time the serviced, recently had a dead battery or a battery replace- vehicle is started.
Page 441: Replacement Parts
MAINTAINING YOUR VEHICLE 439 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced •...
Page 442: Dealer Service
440 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service person- The pages that follow contain the required maintenance nel, special tools, and equipment to perform all service services determined by the engineers who designed your operations in an expert manner.
Page 443: Engine Oil
MAINTAINING YOUR VEHICLE 441 regular intervals, such as every fuel stop. The best time to CAUTION! (Continued) check the engine oil level is about five minutes after a • Your vehicle has been built with improved fluids fully warmed engine is shut off. Do not check oil level that protect the performance and durability of your before starting the engine after it has sat overnight.
Page 444 442 MAINTAINING YOUR VEHICLE Engine Oil Selection CAUTION! For best performance and maximum protection under all Do not overfill the engine. Overfilling the engine types of operating conditions, the manufacturer only will cause oil aeration, which can lead to loss of oil recommends engine oils that are API Certified and meet pressure and an increase in oil temperature.
Page 445 MAINTAINING YOUR VEHICLE 443 Synthetic Engine Oils CAUTION! You may use synthetic engine oils provided the recom- Do not use chemical flushes in your engine oil as the mended oil quality requirements are met, and the recom- chemicals can damage your engine. Such damage is mended maintenance intervals for oil and filter changes not covered by the New Vehicle Limited Warranty.
Page 446: Engine Oil Filter
444 MAINTAINING YOUR VEHICLE station or governmental agency for advice on how and WARNING! where used oil and oil filters can be safely discarded in your area. The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine Engine Oil Filter backfire.
Page 447: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 445 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. • Battery gas is flammable and explosive. Keep You will never have to add water, nor is periodic main- flame or sparks away from the battery. Do not use tenance required.
Page 448: Air Conditioner Maintenance
446 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer battery that the positive cable is attached to the at the start of each warm season.
Page 449 MAINTAINING YOUR VEHICLE 447 Refrigerant Recovery And Recycling WARNING! R-134a Air Conditioning Refrigerant is a hydrofluoro- • Use only refrigerants and compressor lubricants carbon (HFC) that is endorsed by the Environmental approved by the manufacturer for your air condi- Protection Agency and is an ozone-saving product. How- tioning system.
Page 450 448 MAINTAINING YOUR VEHICLE 4. Disengage the two retaining tabs that secure the filter WARNING! cover to the HVAC housing, and remove the cover. Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box.
Page 451: Body Lubrication
MAINTAINING YOUR VEHICLE 449 5. Remove the A/C air filter by pulling it straight out of Body Lubrication the housing. Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, 6. Install the A/C air filter with the arrow on the filter tailgate, sliding doors and hood hinges, should be lubri- pointing toward the floor.
Page 452: Windshield Wiper Blades
450 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Adding Washer Fluid Clean the rubber edges of the wiper blades and the The washer fluid reservoir is located in the engine windshield periodically with a sponge or soft cloth and a compartment, and the fluid level should be checked at regular intervals.
Page 453: Exhaust System
MAINTAINING YOUR VEHICLE 451 Exhaust System WARNING! The best protection against carbon monoxide entry into • Exhaust gases can injure or kill. They contain the vehicle body is a properly maintained engine exhaust carbon monoxide (CO), which is colorless and system.
Page 454 452 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- CAUTION! verter will not require maintenance. However, it is im- • The catalytic converter requires the use of un- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst leaded fuel only.
Page 455: Cooling System
MAINTAINING YOUR VEHICLE 453 To minimize the possibility of catalytic converter damage: Cooling System • Do not shut off the engine or interrupt the ignition, WARNING! when the transmission is in gear and the vehicle is in motion. • When working near the radiator cooling fan, •...
Page 456 454 MAINTAINING YOUR VEHICLE Coolant Checks Cooling System – Drain, Flush, And Refill Check engine coolant (antifreeze) protection every If the engine coolant (antifreeze) is dirty or contains 12 months (before the onset of freezing weather, where visible sediment, clean and flush with OAT coolant applicable).
Page 457 MAINTAINING YOUR VEHICLE 455 CAUTION! CAUTION! (Continued) • Do not use water alone or alcohol-based engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) products. Do not use additional specified Organic Additive Technology (OAT) rust inhibitors or antirust products, as they may not engine coolant (antifreeze), may result in engine be compatible with the radiator engine coolant and damage and may decrease corrosion protection.
Page 458 456 MAINTAINING YOUR VEHICLE • Mix a minimum solution of 50% OAT engine coolant Adding Coolant that meets the requirements of Chrysler Material Stan- Your vehicle has been built with an improved engine dard MS-12106 and distilled water. Use higher concen- coolant (OAT coolant conforming to MS-12106) that trations (not to exceed 70%) if temperatures below allows extended maintenance intervals.
Page 459 MAINTAINING YOUR VEHICLE 457 Cooling System Pressure Cap WARNING! (Continued) The cap must be fully tightened to prevent loss of engine • Do not use a pressure cap other than the one speci- coolant (antifreeze), and to ensure that engine coolant fied for your vehicle.
Page 460 458 MAINTAINING YOUR VEHICLE Coolant Level Points To Remember The coolant bottle provides a quick visual method for NOTE: When the vehicle is stopped after a few miles/ determining that the coolant level is adequate. With the kilometers of operation, you may observe vapor coming engine idling and warm to normal operating tempera- from the front of the engine compartment.
Page 461: Brake System
MAINTAINING YOUR VEHICLE 459 • If frequent engine coolant (antifreeze) additions are Brake System required, the cooling system should be pressure tested In order to assure brake system performance, all brake for leaks. system components should be inspected periodically. • Maintain engine coolant (antifreeze) concentration at a Refer to the “Maintenance Schedule”...
Page 462 460 MAINTAINING YOUR VEHICLE Brake Master Cylinder brake fluid reservoir is low and the brake system does not indicate any leaks or other problems, it may be a The fluid level in the master cylinder should be checked result of a leak in the hydraulic clutch release system. See when performing under hood services, or immediately if your local authorized dealer for service.
Page 463 MAINTAINING YOUR VEHICLE 461 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contaminate moisture, use only new brake fluid or fluid that has the brake fluid. Brake seal components could be been in a tightly closed container.
Page 464: Maintaining Your Vehicle
462 MAINTAINING YOUR VEHICLE Automatic Transmission – If Equipped CAUTION! Selection Of Lubricant (CVT) Using a transmission fluid other than the manufac- It is important to use the proper transmission fluid to turer’s recommended fluid may cause belt slip and ensure optimum transmission performance and life.
Page 465: Manual Transmission - If Equipped
MAINTAINING YOUR VEHICLE 463 CAUTION! CAUTION! Do not use chemical flushes in your transmission as If a transmission fluid leak occurs, visit your autho- the chemicals can damage your transmission compo- rized dealer immediately. Severe transmission dam- nents. Such damage is not covered by the New age may occur.
Page 466: Rear Drive Assembly (Rda) - Awd/4Wd Models Only
464 MAINTAINING YOUR VEHICLE Fluid Level Check Rear Drive Assembly (RDA) – AWD/4WD Models Only Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a Lubricant Selection point not more than 3/16 in (4.7 mm) below the bottom Use only the manufacturers recommended transmission of the hole.
Page 467: Power Transfer Unit (Ptu) - Awd/4Wd Models Only
MAINTAINING YOUR VEHICLE 465 Power Transfer Unit (PTU) – AWD/4WD Models Appearance Care And Protection From Corrosion Only Protection Of Body And Paint From Corrosion Lubricant Selection Vehicle body care requirements vary according to geo- Use only the manufacturer’s recommended fluid. Refer graphic locations and usage.
Page 468 466 MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumu- What Causes Corrosion? lated on your vehicle, use MOPAR® Super Kleen Bug Corrosion is the result of deterioration or removal of and Tar Remover to remove. paint and protective coatings from your vehicle.
Page 469 MAINTAINING YOUR VEHICLE 467 • If you carry special cargo such as chemicals, fertilizers, Special Care de-icer salt, etc., be sure that such materials are well • If you drive on salted or dusty roads or if you drive packaged and sealed. near the ocean, hose off the undercarriage at least once •...
Page 470 468 MAINTAINING YOUR VEHICLE • For tough stains, apply MOPAR® Total Clean, or a CAUTION! mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. Do not use scouring pads, steel wool, a bristle brush, or metal polishes.
Page 471 MAINTAINING YOUR VEHICLE 469 Your leather upholstery can be best preserved by regular Cleaning Headlights cleaning with a damp soft cloth. Small particles of dirt Your vehicle has plastic headlights that are lighter and can act as an abrasive and damage the leather upholstery less susceptible to stone breakage than glass headlights.
Page 472 470 MAINTAINING YOUR VEHICLE Glass Surfaces Instrument Panel Cover All glass surfaces should be cleaned on a regular basis The instrument panel cover has a low glare surface which with MOPAR® Glass Cleaner, or any commercial minimizes reflections on the windshield. Do not use household-type glass cleaner.
Page 473 MAINTAINING YOUR VEHICLE 471 Cleaning Plastic Instrument Cluster Lenses Seat Belt Maintenance The lenses in front of the instruments in this vehicle are Do not bleach, dye, or clean the belts with chemical molded in clear plastic. When cleaning the lenses, care solvents or abrasive cleaners.
Page 474: Fuses
472 MAINTAINING YOUR VEHICLE FUSES Integrated Power Module The Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed on the inside of the cover.
Page 475 MAINTAINING YOUR VEHICLE 473 Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse Empty Empty 10 Amp Power Mirror/ Steering Control 15 Amp AWD/4WD Control Satellite Radio/ Lt Blue Module – If Equipped Hands-Free Phone 10 Amp Rear Center Brake 30 Amp...
Page 476 474 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse 15 Amp Power Outlet 10 Amp Wireless Control Lt Blue Module 20 Amp 115V AC Inverter – 40 Amp Auto Shutdown Relay Yellow If Equipped Green...
Page 477 MAINTAINING YOUR VEHICLE 475 Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse 15 Amp Auto Shutdown Relay Hot Car (No Fuse Lt Blue Required) 15 Amp Power Sunroof – 20 Amp Heated Seat – Lt Blue If Equipped Yellow...
Page 478 476 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description CAUTION! tridge Fuse • When installing the IPM cover, it is important to Fuse ensure the cover is properly positioned and fully 40 Amp Antilock Brake Pump latched. Failure to do so may allow water to get into Green the IPM, and possibly result in an electrical system 30 Amp...
Page 479: Vehicle Storage
MAINTAINING YOUR VEHICLE 477 VEHICLE STORAGE REPLACEMENT BULBS If you will not be using your vehicle for more than All the inside bulbs are brass or glass wedge base. 21 days, you may want to take steps to preserve your Aluminum base bulbs are not approved and should not battery.
Page 480: Bulb Replacement
478 MAINTAINING YOUR VEHICLE Exterior Bulbs BULB REPLACEMENT Bulb Number Headlamps Low Beam Headlamp 1. Raise the hood and locate the connector behind the High Beam Headlamp 9005 headlamp. Front Park/Turn Signal 7444NA 2. Reach into the engine compartment and pull the red Lamp lock out at the green connector.
Page 481: Fog Lamps
MAINTAINING YOUR VEHICLE 479 Fog Lamps 2. Grasp the taillamp and pull firmly to disengage the lamp from the aperture panel. 1. Access lamp through the lower fascia cutout. 3. Twist and remove socket from lamp. 2. Remove electrical connector from bulb. 3.
Page 482: Fluid Capacities
480 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 13.6 Gallons 51.5 Liters Engine Oil with Filter 2.0L and 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 4.26 Liters Cooling System * 2.0L and 2.4L Engine (MOPAR® Antifreeze/ 7.2 Quarts 6.8 Liters Engine Coolant 10 Year/150,000 Mile Formula or equivalent)
Page 483: Fluids, Lubricants And Genuine Parts
MAINTAINING YOUR VEHICLE 481 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Chrysler Material Standard MS-12106. Engine Oil We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 484: Chassis
482 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission We recommend you use MOPAR® CVTF+4® Continuously Variable Transmission (CVT) – If Equipped Fluid. Manual Transmission – We recommend you use MOPAR® ATF+4® Automatic Transmission Fluid. If Equipped Rear Drive Assembly (RDA) We recommend you use MOPAR®...
Page 485: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS ▫ Maintenance Chart.....486 MAINTENANCE SCHEDULE ... . .484...
Page 486 484 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE On Electronic Vehicle Information Center (EVIC) equipped vehicles, “Oil Change Required” will be displayed in the Your vehicle is equipped with an automatic oil change EVIC and a single chime will sound, indicating that an oil indicator system.
Page 487 MAINTENANCE SCHEDULES 485 NOTE: Under no circumstances should oil change inter- At Every Oil Change Interval As Indicated By vals exceed 10,000 miles (16,000 km) or twelve months, Oil Change Indicator System: whichever comes first. • Change oil and filter Once A Month Or Before A Long Trip: •...
Page 488 486 MAINTENANCE SCHEDULES Maintenance Chart Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals.
Page 489 MAINTENANCE SCHEDULES 487 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Maintenance Replace engine air cleaner filter. Replace air conditioning/cabin air filter. Replace spark plugs ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 490 488 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Replace power transfer unit (PTU) fluid. Change automatic transmission fluid and filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing.
Page 491 MAINTENANCE SCHEDULES 489 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Change the manual transmission fluid if using your vehicle for any of the following: trailer towing, heavy loading, taxi, police, deliv- ery service (commercial service), off-road, desert operation or more than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C).
Page 492 490 MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to per- form a service job, take your vehicle to a competent mechanic.
Page 493 IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ....493 Speech Impaired (TDD/TTY) ... . .495 ▫...
Page 494 492 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... . .500 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ..499 ▫...
Page 495: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 493 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 496: Chrysler Group Llc Customer Center
494 IF YOU NEED CONSUMER ASSISTANCE Warranty service must be done by an authorized dealer. Any communication to the manufacturer’s customer cen- We strongly recommend that you take the vehicle to an ter should include the following information: authorized dealer. They know your vehicle the best, and •...
Page 497: Chrysler Canada Inc. Customer Center
IF YOU NEED CONSUMER ASSISTANCE 495 Chrysler Canada Inc. Customer Center Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) P.O. Box 1621 To assist customers who have hearing difficulties, the Windsor, Ontario N9A 4H6 manufacturer has installed special TDD (Telecommuni- Phone: (800) 465–2001 English / (800) 387–9983 French cation Devices for the Deaf) equipment at its customer center.
Page 498: Service Contract
496 IF YOU NEED CONSUMER ASSISTANCE Service Contract contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the You may have purchased a service contract for a vehicle contract documents, and contact the person listed in to help protect you from the high cost of unexpected those documents.
Page 499: Warranty Information
IF YOU NEED CONSUMER ASSISTANCE 497 REPORTING SAFETY DEFECTS WARNING! (Continued) In The 50 United States And Washington, D.C. birth defects, or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain If you believe that your vehicle has a defect that could products of component wear contain, or emit, chemi- cause a crash or cause injury or death, you should cals known to the State of California to cause cancer...
Page 500: In Canada
498 IF YOU NEED CONSUMER ASSISTANCE Washington, D.C. 20590. You can also obtain other infor- NOTE: A street address is required when ordering mation about motor vehicle safety from http:// manuals (no P.O. Boxes). www.safercar.gov. Service Manuals In Canada These comprehensive Service Manuals provide the infor- mation that students and professional technicians need If you believe that your vehicle has a safety defect, you in diagnosing/troubleshooting, problem solving, main-...
Page 501: Department Of Transportation Uniform Tire Quality Grades
IF YOU NEED CONSUMER ASSISTANCE 499 the first time, using step-by-step troubleshooting and driv- DEPARTMENT OF TRANSPORTATION UNIFORM ability procedures, proven diagnostic tests and a complete TIRE QUALITY GRADES list of all tools and equipment. The following tire grading categories were established by the National Highway Traffic Safety Administration.
Page 502: Traction Grades
500 IF YOU NEED CONSUMER ASSISTANCE significantly from the norm due to variations in driving Temperature Grades habits, service practices, and differences in road charac- The temperature grades are A (the highest), B, and C, teristics and climate. representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under Traction Grades controlled conditions on a specified indoor laboratory...
Page 503 IF YOU NEED CONSUMER ASSISTANCE 501 WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure.
Page 505 INDEX...
Page 506 504 INDEX ABS (Anti-Lock Brake System) ....339 Air Pressure, Tires......363 Adding Engine Coolant (Antifreeze) .
Page 507 INDEX 505 Fluid and Filter Changes ....463 Parking ......336 Fluid Level Check .
Page 508 506 INDEX Luggage Carrier ......205 Clock ........244 Cargo Light .
Page 509 INDEX 507 Coolant Level ......454 Dimmer Switch, Headlight....166 Disposal of Used Coolant .
Page 510 508 INDEX Electronic Speed Control (Cruise Control) ..173 Oil ........441 Electronic Stability Control (ESC) .
Page 511 INDEX 509 Flashers Freeing A Stuck Vehicle .....427 Hazard Warning ......408 Fuel .
Page 512 510 INDEX Garage Door Opener (HomeLink®) ... .176 Hands-Free Phone (Uconnect®) ....111 Gas Cap (Fuel Filler Cap) ....388 Hazard Warning Flasher .
Page 513 INDEX 511 HomeLink® (Garage Door Opener) ... .176 Jacking Instructions ......412 Hood Release .
Page 514 512 INDEX Lead Free Gasoline ......384 Electronic Stability Program (ESP) Indicator ..351 Leaks, Fluid ......102 Engine Temperature Warning .
Page 515 INDEX 513 Security Alarm (Theft Alarm) ....19 Maintenance Free Battery....445 Service .
Page 516 514 INDEX Exterior Folding ......109 Oil Change Indicator ..... . .233 Heated .
Page 517 INDEX 515 Overheating, Engine ..... . .220 Transfer Unit ......465 Owner’s Manual (Operator Manual) .
Page 518 516 INDEX Rear Window Features .....203 Restraint, Head......155 Rear Wiper/Washer.
Page 519 INDEX 517 Seat Belts ....... .40 Security Alarm (Theft Alarm)....18 Adjustable Shoulder Belt .
Page 520 518 INDEX Speedometer......215 Supplemental Restraint System - Airbag ..62 Starting .
Page 521 INDEX 519 General Information .....362 Tire Safety Information .....352 High Speed .
Page 522 520 INDEX Transaxle Universal Transmitter ..... .176 Automatic ......12 Unleaded Gasoline .
Page 523 INDEX 521 Washer Adding Fluid ......450 Washers, Windshield ..... . .170 Washing Vehicle .
Page 524 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use only frequency signals.
Page 525 Chrysler Group LLC 13MK49-126-AD Printed in U.S.A. 4th Edition...

Jeep Compass 2013 Owner's Manual

Introduction

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Jeep Compass 2013

Summary of Contents for Jeep Compass 2013