Safety And Troubleshooting Information; Installation Locations - Philips 220VW8FB/00 Service Manual

Safety and Troubleshooting Information

Safety precautions and maintenance
WARNING: Use of controls, adjustments or
procedures other than those specified in this
documentation may result in exposure to shock,
electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and using
your computer monitor:
a. To protect your display from possible damage, do not put
excessive pressure on the LCD panel. When moving your
monitor, grasp the frame to lift; do not lift the monitor by
placing your hand or fingers on the LCD panel.
b. Unplug the monitor if you are not going to use it for an
extensive period of time.
c. Unplug the monitor if you need to clean it with a slightly
damp cloth. The screen may be wiped with a dry cloth when
the power is off. However, never use alcohol, solvents or
ammonia-based liquids.
d. Consult a service technician if the monitor does not operate
normally when you have followed the instructions in this
manual.
e. The casing cover should be opened only by qualified service
personnel.
f. Keep the monitor out of direct sunlight and away from stoves
or any other heat source.
g. Remove any object that could fall into the vents or prevent
proper cooling of the monitor's electronics.
h. Do not block the ventilation holes on the cabinet.
i. Keep the monitor dry. To avoid electric shock, do not expose
it to rain or excessive moisture.
j. When positioning the monitor, make sure the power plug and
outlet are easily accessible.
k. If turning off the monitor by detaching the power cable or DC
power cord, wait for 6 seconds before attaching the power
cable or DC power cord for normal operation.
l. To avoid the risk of shock or permanent damage to the set,
do not expose the monitor to rain or excessive moisture.
m. IMPORTANT: Always activate a screen saver program during
your application. If a still image in high contrast remains on
the screen for an extended period of time, it may leave an
'after-image' or 'ghost image' on front of the screen. This is a
well-known phenomenon that is caused by the shortcomings
inherent in LCD technology. In most cases, the afterimage
will disappear gradually over a period of time after the power
has been switched off. Be aware, that the afterimage
symptom cannot be repaired and is not covered under
warranty.
o. Warning for lifting monitor - Do not use the area underneath
the logo cover to grip or lift the monitor. Placing weight on the
logo cover can cause it to break away from the body and
cause the monitor to fall. When lifting the monitor, place one
hand under the monitor's frame.
* Consult a service technician if the monitor does not operate
normally when the operating instructions given in this manual
have been followed.

Installation Locations

Avoid exposure to heat and extreme cold.
Do not store or use the LCD monitor in locations exposed to
heat, direct sunlight or extreme cold.
Avoid moving the LCD monitor between locations with large
temperature differences. Choose a site that falls within the
following temperature and humidity ranges.
Temperature: 0-35°C 32-95°F
Humidity: 20-80% RH
Do not subject the LCD monitor to severe vibration or high
impact conditions. Do not place the LCD monitor in the trunk of
a car.
Take care not to mishandle this product by either knocking or
dropping it during operation or transportation.
Do not store or use the LCD monitor in locations where there is
a high level of humidity or in dusty environments. Do not allow
water or other liquids to spill on or into the LCD monitor.
Trouble Shooting
This page deals with problems that can be corrected by the
user. If the problem still persists after you have tried these
solutions, contact your nearest Philips dealer.
Common Problems
Having this problem Check these items
a. Make sure the power cord is plugged into the power
No Picture outlet and into the back of the monitor.
b. First, ensure that the power button on the front of the
(Power LED not lit) monitor is in the OFF position, then press it to the ON
position.
a. Make sure the computer is turned on.
No Picture
b. Make sure the signal cable is properly connected to
your computer.
(Power LED is amber or
c. Check to see if the monitor cable has bent pins.
yellow)
d. The Energy Saving feature may be activated.
Screen says
a. Make sure the monitor cable is properly connected
to your computer.
ATTENTION
(Also refer to the Quick Set-Up Guide).
b. Check to see if the monitor cable has bent pins.
ENTERING SLEEPING MODE
c. Make sure the computer is turned on.
Screen says
a. Make sure the vertical sync of input signal is within
the range of 56 ~ 75 Hz.
ATTENTION
b. Change the refresh rate to 56~75Hz within
CANNOT DISPLAY THIS VIDEO
10 minutes.
MODE, CHANGE COMPUTER DISPLAY
INPUT TO 1680X1050 @60HZ c. Re-power on monitor to start over again if you failed
to change the refresh rate within 10 minutes.
a. The Auto Function is designed for use on standard
Macintosh or IBM-compatible PCs running Microsoft
Windows.
AUTO button not working
b. It may not work properly if using nonstandard PC or
properly
video card.
c. The AUTO adjustment does not function when digital
input is used for display.
Imaging Problems
a. Press the Auto button.
b. Adjust the image position using the
Display position is incorrect
Horizontal Position and/or Vertical Position
in OSD Main Controls.
a. Check that the signal cable is properly connected
Image vibrates on the screen
to the graphics board or PC.
a. Press the Auto button.
Vertical flicker appears b. Eliminate the vertical bars using the Phase/Clock
of More Settings in OSD Main Controls.
a. Press the Auto button.
Horizontal flicker appears b. Eliminate the vertical bars using the Phase/Clock
of More Settings in OSD Main Controls.
220VW8 LCD 9