Home Network System Window/Door Sensor KX-HNS101 Model No. Thank you for purchasing a Panasonic product. This document explains how to install the window/door sensor properly. For details about how to use the system, refer to the User’s Guide (page 17).
Table of Contents Introduction Accessory information ....3 Important Information About this system ......4 For your safety ......4 Important safety instructions ..5 For best performance ....5 Other information .......6 Setup Part names and functions ..8 About the LED indicator .....8 Setup overview ......8 Inserting the battery ....9 Registering the window/door sensor ........9...
R Design and specifications are subject to change without notice. R The illustrations in these instructions may vary slightly from the actual product. Trademarks R iPhone and iPad are registered trademarks of Apple Inc. R Android™ is a trademark of Google Inc. For assistance, please visit www.panasonic.com/support...
This system is an auxiliary system; it is not designed to provide complete R Do not disassemble the product. protection from property loss. Panasonic will not be held responsible Medical in the event that property loss occurs R Consult the manufacturer of any while this system is in operation.
R Remove the battery if it becomes unusable. There is a risk of leakage, The hub and other compatible overheating, and rupture. Do not Panasonic devices use radio waves to attempt to use a battery if it is communicate with each other. leaking.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Routine care R Wipe the outer surface of the product with a soft moist cloth. For assistance, please visit www.panasonic.com/support...
Page 7
Important Information Notice For assistance, please visit www.panasonic.com/support...
(page 11). Indicator Status Installation Green, lit Window/door is closed Install the window/door sensor on Red, lit Window/door is open the same position where proper For assistance, please visit www.panasonic.com/support...
Attach the sensor unit cover. R If registration fails, the hub sounds several short beeps. Using the app When you register the window/door sensor by using the [Home Network] app, you can assign a name to your For assistance, please visit www.panasonic.com/support...
M N. If the LED indicator is lit in green or red, the sensor is communicating properly with the hub. If the LED indicator blinks in red, it is out of range of the hub. For assistance, please visit www.panasonic.com/support...
R Depending on the condition and material of the surface where the sensor unit and magnet unit are installed, the LED indicator may light in red even if the “ ” marks point directly at each other and are no more than 25.4 mm (1 inch) apart. For assistance, please visit www.panasonic.com/support...
Page 12
“ ” marks are not aligned. Magnet other and are within 25.4 mm (1 inch). unit is too high/too low. {xC} {xC} GREEN “ ” marks are aligned but units are too far apart. {xC} For assistance, please visit www.panasonic.com/support...
Page 13
“ ” marks are not aligned. Magnet other and are within 25.4 mm (1 inch). unit is too high/too low. GREEN {xC} {xC} “ ” marks are aligned but units are too far apart. {xC} For assistance, please visit www.panasonic.com/support...
R Use screws when installing on a wooden surface. Do not use double-sided tape. Securing with screws Remove the covers from each unit. R Lift from the indented area (A) and open the sensor unit cover (B). For assistance, please visit www.panasonic.com/support...
Page 15
Attach the covers. Important: Align the “ ” marks on the sensor unit and the magnet unit so that they point directly at each other and are no more than 25.4 mm (1 inch) apart. For assistance, please visit www.panasonic.com/support...
Page 16
Removing when secured with double-sided tape Tie a piece of thread to two sticks, screwdrivers, etc. Pull the thread tight and use it to cut the double-sided tape, and then remove any excess tape. Excess tape For assistance, please visit www.panasonic.com/support...
– Security system www.panasonic.net/pcc/support/tel/ You can use the app to arm and homenetwork/manual/ disarm the security system, confirm the current status of the sensor, and view a log of previous security events. – Home control For assistance, please visit www.panasonic.com/support...
Magnet unit: Approx. 37 mm ´ 14 mm ´ 14 mm (1 15/32 inches ´ 9/16 inches ´ 9/16 inches) R Mass (weight) Sensor unit: Approx. 39 g (0.09 lb), excluding the battery Magnet unit: Approx. 8 g (0.02 lb) For assistance, please visit www.panasonic.com/support...
FCC RF exposure turning the equipment off and on, the requirements. user is encouraged to try to correct the For assistance, please visit www.panasonic.com/support...
Page 20
Appendix Notice: R FCC ID can be found inside the sensor unit. For assistance, please visit www.panasonic.com/support...
For hearing or speech impaired TTY users, TTY: 1-877-833-8855 Accessory Purchases (United States and Puerto Rico) Purchase Parts, Accessories and Owner’s Manual online for all Panasonic Products by visiting our Web Site at: www.pstc.panasonic.com or, send your request by E-mail to: npcparts@us.panasonic.com You may also contact us directly at:1-800-237-9080 (Fax Only) (Monday - Friday 9 am to 9 pm, EST.)
If your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“Limited Warranty period”), at its option either (a) repair your product with new or...
Page 23
Send the unit to Panasonic Exchange Center, prepaid and adequately insured. Do not send your unit to Panasonic Corporation of North America listed on the back cover or to executive or regional sales offices. These locations do not repair consumer products.