Related Manuals for Blade BLH3300
Summary of Contents for Blade BLH3300
- Page 1 Instruction Manual Bedienungsanleitung Manuel d’Utilisation Manuale di Istruzioni...
-
Page 2: Safety Precautions And Warnings
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product. Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury. -
Page 3: Table Of Contents
Stunt Mode ...............9 the European Union ............16 Installing the Flight Battery ..........10 Blade Nano CP X Features Ready To Fly Bind-N-Fly Airframe – Blade Nano CP X Included Included Main and Tail Motors – Brushed Installed Installed On-board Electronics – Flybarless 3-in-1 Control Unit, RX/ESCs/... -
Page 4: Charging Warnings
Charging Warnings The Battery Charger (EFLC1000) included with your helicopter has been designed to safely charge the Li-Po • Always charge batteries away from battery. flammable materials. • Always inspect the battery before charging. CAUTION: All instructions and warnings must be • Always disconnect the battery after charging, and let followed exactly. Mishandling of Li-Po batteries can the charger cool between charges. -
Page 5: As3X Flybarless Helicopter Technology
AS3X Flybarless Helicopter Technology The Blade Nano CP X features on-board AS3X flybar- The AS3X technology also improves tracking, stability and ® less technology. AS3X technology combines 3-axis gyro cyclic response for intermediate and advanced pilots. ® stabilization with a new flybarless colective pitch rotor However, the AS3X flybarless system is not a flying aid for head, resulting in less drag, fewer parts and increased beginners. - Page 6 HELI 0-AILE 100% 30% NORM 100% 0-AILE 100% ST-1 100% INH INH% 100% 0-ELEV 100% 30% STUNT 100% 100% 100% 100% 100% 0-ELEV 100% ST-2 100% 100% 100% 100% 100% Reverse Swash Type 0-RUDD 100% INH HOLD 0-RUDD 100% HOLD THRO N 1 Servo 90 1-AILE...
-
Page 7: Transmitter And Receiver Binding
® Transmitter and Receiver Binding If you purchased an RTF model, the transmitter is bound to the model at the factory. To bind or re-bind your Nano CP X to your chosen transmitter, please follow the directions below: Binding is the process of programming the receiver of the control unit to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum DSMX technology... -
Page 8: Understanding The Primary Flight Controls
Understanding the Primary Flight Controls If you are not familiar with the controls of your Nano CP X, take a few minutes to familiarize yourself with them before attempting your first flight. Throttle Mode 1 Mode 2 (model viewed from left) Descend Ascend Throttle up Throttle down Rudder Mode 1 Mode 2 (model viewed from top) Nose Yaws Left Nose Yaws Right Rudder left Rudder right Elevator... -
Page 9: Throttle Hold
Throttle Hold Throttle hold is used to turn off the helicopter motors if the helicopter is out of control, in danger of crashing or both. Activate throttle hold anytime the helicopter is in danger to reduce the chance of damaging the helicopter in a crash. -
Page 10: Installing The Flight Battery
Consult local laws and ordinances before choosing a location to fly your aircraft. Select a large, open area away from people and objects. The Blade Nano CP X can fly outdoors on a calm day or indoors in a gymnasium. -
Page 11: Troubleshooting Guide
Do not hold the bind button/ switch non-computer radio computer radios after applying left rudder Tail boom is cracked Replace tail boom Poor tail authority The tail rotor blade is warped or bent Twist rotor blade back into position or replace Climb out rate is greatly Main gear has slipped on the main Push main gear back into position reduced shaft... -
Page 12: Exploded View And Parts Listings
Exploded View and Parts Listings... -
Page 13: Optional Parts
Feathering Spindle w/O-Rings & Part # Description L BLH3313 Hardware: Nano CP X Flybarless 3-in-1 Control Unit, RX/ A BLH3301 Main Blade Grips with Bearings: ESCs/Gyros: Nano CP X M BLH3314 Nano CP X Tail Boom Assembly w/Tail Motor/ B BLH3302 N BLH3315... -
Page 14: Limited Warranty
Limited Warranty What this Warranty Covers to better answer your questions and service you in the event Horizon Hobby, LLC (Horizon) warrants to the original pur- that you may need any assistance. For questions or assis- chaser that the product purchased (the “Product”) will be tance, please visit our website at www.horizonhobby.com, free from defects in materials and workmanship at the date submit a Product Support Inquiry, or call 877.504.0233 toll... -
Page 15: Warranty And Service Contact Information
Warranty and Service Contact Information Country of Horizon Hobby Contact Information Address Purchase Horizon Service Center servicecenter.horizonhobby.com/ (Repairs and Repair Requests) RequestForm/ www.quickbase.com/db/ Horizon Product Support United States of 4105 Fieldstone Rd bghj7ey8c?a=GenNewRecord (Product Technical Assistance) America Champaign, Illinois, 61822 USA 888-959-2304 sales@horizonhobby.com Sales... -
Page 16: Fcc Information
Compliance Information for the European Union Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2012081003U1 Product(s): Blade nCPX Brushless RTF Item Number(s): BLH3300BLC Equipment class: The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 2006/95/EC: EN 300-328 V1.8.1... -
Page 17: Instructions For Disposal Of Weee By Users In The European Union
Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2012081002 Product(s): Nano CP X BNF Item Number(s): BLH3380 Equipment class: The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 2006/95/EC: EN 301 489-1 V1.7.1: 2006 EN 301 489-17 V1.3.2: 2008...
Need help?
Do you have a question about the BLH3300 and is the answer not in the manual?
Questions and answers