Related Manuals for Yudor YSS-1523A-OIP
Summary of Contents for Yudor YSS-1523A-OIP
- Page 1 IP SPEED DOME USER’S MANUAL YSS-1523A-OIP / YSS-2523A-OIP YSS-1523B-OIP / YSS-2523B-OIP YSS-1523W-OIP / YSS-2523W-OIP YSS-1523U-OIP / YSS-2523U-OIP V3.0...
-
Page 3: Safety Warning
All rights are reserved. No part of this document may be photocopied reproduced or 2. When the SD card is full, it will overwrite the oldest video files automatically. translated to another language without the prior written consent of Yudor Co., Ltd. 31.532 Record Setting: Modify Pre/ Post Alarm seconds (Each 0~5 seconds). -
Page 4: Table Of Contents
Table of Contents 31.52 I/O setting and Mail & FTP & Logs: Safety warning Instructions 1. Accessories 1.1 Outdoor with heater & Blower 2. Camera Installation I/O Out1 ~ Out4 and Mode setting is reserved in option. 2.1 Outdoor with heater & Blower 3. - Page 5 Camera Operation In each area can choose actions when motion alarm is triggered. 6. Infrared remote control mode Interval: 10-60 seconds. Based on the schedule: alarm action is based on schedule. 6.1 Select Camera - By Input camera ID 31.512 Record file format: AVI or JPEG 6.2 Remote control 6.3 Alarm and Output On / Off 6.4 Preset Positions CALL, SAVE and CLEAR...
- Page 6 31.5 Event List: 31.4 A/V Setting 31. 42 Video Setting 31.5 Event List (Motion Detect) 31.52 FTP & MAIL Recording Software 16Ch recording software menu Software Specifications Mobile Viewer Software PDA/Smartphone Viewer Appendix – Network Connecting 31.51 Event Setting 31.511 Motion Detection & Sensitivity: When motion is triggered, it can send the video to specific mail address;...
-
Page 7: Accessories
Resolution: D1 – 720X480 CIF – 320X240 QCIF – 160X120 (NTSC) 1-Accessories D1 – 720X576 CIF – 320X288 QCIF – 160X144 (PAL) Quality: Best, High, Standard, Medium, Low Please check if the accessories enclosed are completed. If there is any Video System: 60Hz (NTSC) or 50Hz (PAL) shortage, please contact your local dealer and replace a new one. -
Page 8: Outdoor With Heater & Blower
2-Installation Ad-hoc: Point to Point Mode. Infrastructure: AP Mode. 2.1 Outdoor with heater & Blower 31.364 Operation Mode: Auto/11b (Max. 11Mb)/11g (Max. 54Mb) 2.1.1 Names of parts 31.365 SSID: The name of Access Point that Speed Dome desire to connect. A. - Page 9 2.1.2.3 Loads cover back and tightened all securing screws (Turn clockwise). Make sure all the screws are properly tightened to keep camera waterproof State: Idle No DDNS Service 2.1.2.4 Use securing screws (accessory 1.1.9) and choice of Wall mount bracket http ://<username>.ddns.camddns.com DDNS Service Active (accessory 1.1.10) or Ceiling mount bracket (accessory 1.1.11) install camera...
-
Page 10: Wire Specification
3-Cable Connection 31.35 DDNS: Supports DDNS (Dynamic DNS) service. 31.351 DynDNS: Only Dynamic service 3.1 A-O Series Key-in the hostname, username and password. Schedule update: Default is 5 minutes. Please note that hostname will be blocked by DynDNS if schedule update is more than once every 5 minutes to 60 minutes. -
Page 11: Infrared Remote Control
4-Infrared Remote control Clear / Camera ID Display key Camera selected key. Number key for Input camera ID /Function setting Alarm/subtitle display on or off 31.32 Static IP：IP Address, Subnet Mask, Gateway and DNS 0/1 manually. ARK-503 Alarm/subtitle display setting 31.33 DHCP：Using DHCP, it will get all the network parameters automatically from router. -
Page 12: Initial Programming
5-Initial Programming Be sure to keep the remote control within 7 meters from the receiver. All inputs shall be made within 5 seconds, or the input mode would be cancelled automatically. In case of erroneous input, press LK to clear or escape from the operating mode. -
Page 13: Load Default
※ There is no time limit on the process of camera ID setup ※ 〝 Default of camera ID is 000. If you only use one camera you don’t have to setup camera ID. You can operate all function through remote control directly. ※... -
Page 14: Autopan
5.4.1.1 AUTO PAN 31.2 Configuration: Select →AUTO PAN 001 SYSTEM SETUP 31.21 Control Interface: GROUP-SET AUTOPAN START-POINT: PAN LIMIT TO THE LEFT START-POINT →ENT. END-POINT : PAN LIMIT TO THE RIGHT END-POINT ENT. AUTO PAN SPEED SETUP 2.5 ﾟ~ 60 ﾟ/s SPEED RUNNING ENT. -
Page 15: Alarm (Alarm Mode Setup)
5.4.1.3.1 RECORDING 1. Press END to start recording 001 SYSTEM SETUP 31.11 : Administration page ; : Snapshot ; : Live Video 2. Use direction key to control camera to the spot CRUISE RECORDING 31.12 : (Option Reserved) need to be monitoring 31.13 Online visitors: How many people is connecting to this IP Dome. -
Page 16: Mask
DELAY：Delay time setup, after finish delay time count down , camera will back to 31. Live Video original status before alarm triggered. Start a IE browser, type the IP address of the IP camera in the address field. It will show BY SAT Delay time will automatically go with 5.4.4 TRACKING delay time The default user the following dialogue box. - Page 17 5.4.3.2 SETUP POSITION AND SIZE OF MASKING Enter SAVE, Use UP、DN key to adjust position 001 SYSTEM SETUP and size of masking. Exit SAVE to finish setup. MASK NO .1 MODIFY H-POS. →08 H-POS. Horizontal position adjustment V-POS. H-SIZE V-POS. Vertical position adjustment V-SIZE Horizontal size adjustment H-SIZE...
-
Page 18: Tracking
5.4.5 PROTOCOL Select→PROTOCOL (For RS-485 systems) 001 SYSTEM SETUP 30.42 Change color quality to highest (32bit). GROUP DYNA9600 (DYNACOLOR Rate 9600) ALARM ELITAR2400 (ELITAR Rate 2400) MASK CHIPER9600 TRACKING (CHIPER Rate 9600) PROTOCOL →DANA9600 LILIN9600 (LILIN Rate 9600) PELCOD2400 (PELCO-D Rate 2400) MISC CAMERA PELCOP4800... -
Page 19: Camera
5.4.7.2 AUTO-FLIP 30.32 The GUI of the IP Installer: 001 SYSTEM SETUP AUTO-FLIP MISC Select→AUTO-FLIP SPEED →AUTO-FLIP DEFAULT ENT. 5.4.7.3 DEFAULT 001 SYSTEM SETUP DEFAULT MISC All Setup will restore DEFAULT SPEED Except PROTOCOL and camera ID. AUTO-FLIP →DEFAULT ENT. 5.4.8 CAMERA 001 SYSTEM SETUP Select→CAMERA... -
Page 20: Infrared Remote Control Mode
6-Infrared Remote Control mode 30. Network IP Assignment 30.1 Use the software, “IP Installer” to assign the IP address. The software is in the 6.1 Select Camera - By Input camera ID attached software CD. 6.1.1 Press CAM then CALL ID<001-255>: - - - show on the screen. 30.2 There are two languages for the IP installer 6.1.2 Input CAMERA ID (Three digits) then you can set function or control 30.21 IPInstallerCht.exe: Chinese version... -
Page 21: Preset Positions Call, Save And Clear
29.4 PRIORITY 6.4 Preset positions Call, Save and Clear Selecting IR SW INT Detecting Signal 6.4.1 Call Press PRE once then input camera ID CALL PRESET: - - MISC Move cursor to PRIORITY, press ENTER key to enter PRE→0→2 call preset 02 PRIORITY menu. -
Page 22: Rs-485 Control Mode
29.1 H-REVERS 7-RS-485 Control mode Horizontal Reverse (Mirror) Function MISC Move cursor to H-REVERS, press ENTER key to enter FREEZE ON/OFF menu. 7.1 Initial Programming →OFF H-REVERS V-REVERS If camera needs to connect to DVR or control panel (KEY PAD) you need to setup POSI/NEGA POSI Press UP or DOWN key to select ON/OFF. -
Page 23: Maintenance & Cleaning
27 SCALE 8-Maintenance & cleaning ZOOM SCALE DISPLAY Daily cleaning Use a piece of soft and dry cloth to wipe off the dust from the dome cover. Dirt SETUP MENU [5/5] Move cursor to SCALE, press ENTER key to enter or scratch may influence focusing. -
Page 24: Troubleshooting
24 GAMMA 9-Troubleshooting GAMMA SELECT 9.1 When no video image on the screen after successful mounting. SETUP MENU [4/5] Move cursor to set GAMMA menu, press ENTER key to 9.1.1 Make sure the video output connector of the camera is properly connected to DEFAULT CANCEL select GAMMA mode , then Press UP or DOWN key to... -
Page 25: Specifications
21 FREEZE MODE 10- Specifications FREEZE FIELD (or FRAME) OF PICTURE FUNCTION SETUP MENU [4/5] CAMERA Move cursor to FREEZE MODE, press ENTER key to DEFAULT CANCEL select FREEZE MODE menu. Pick-UP Device: 1/4” COLOR CCD SONY EXVIEW HAD / SUPER HAD (Day & Night) FREEZE Sync System: Internal synchronous →FIELD... - Page 26 WiFi (optional) 18 INITIAL Indoor: 35 ~ 100 meters(depends on environment) Range Coverage Outdoor: 100 ~ 300 meters (depends on environment) FOCUS RESET FUNCTION IEEE 802.11b (DSSS); IEEE 802.11g (OFDM) Radio 1, 2, 5.5, 6, 11, 12, 18, 24, 36, 48 and 54Mbps (auto sense) SETUP MENU [3/5] Transmission Rate...
-
Page 27: Optional Accessories
11-Optional accessories *1 *2 *3 OFF x 12 x 16 x 32 x 64 BASE YSS-02D/03D Multi-function keyboard For RS-485 control system Expandable to a medium or large system for integrated controls Extra-large LCD for easy reading Built-in universal joy stick of easy handling A variety of functions programmable with push buttons Apt for use in indoor environments... - Page 28 YSS-01WM Reinforced wall Mount Bracket MOTION Press ENTER key to enter MOTION FUNCTION menu. Easy installation Press UP or DOWN key to select motion detection AREA, →AREA Rigid and aesthetically designed LEVEL (Sensitivity), TIME, OSD. Made of rigid materials LEVEL TIME 30sec Apt for use in indoor and outdoor...
-
Page 29: Lens Internal Setting
14 H-GAIN 12-Lens internal setting This is used to enhance the compensation of the picture quality. H-GAIN: Horizontal Compensation SETUP MENU [3/5] Move cursor to H-GAIN, press ENTER key to enter POSITION LOAD. H-GAIN ADJUSTMENT menu. →+6 H-GAIN SETUP MENU [1/5] SETUP MENU [2/5]... - Page 30 1 CAMERA ID POSITION SAVE There have 64 steps (position with zoom & focus) can be Move cursor to CAMERA ID, press ENTER key to enter →1 POSITION SAVE SETUP MENU [1/5] programmed. ID FUNCTION SELECTING menu, then Press UP or →ON.
-
Page 31: Auto Focus
11 FOCUS 2 SENSE UP Move cursor to FOCUS, press ENTER key to enter SETUP MENU [2/5] SETUP MENU [1/5] FOCUS ADJUSTMENT menu. Move cursor to SENSE UP, press ENTER key to enter WHITE BAL AWB. CAMERA ID SENSE UP FUNCTION SELECTING menu, then Press UP SYNC →OFF SENSE UP... -
Page 32: Digital Zoom
3.2 AISHUT FIX MODE 8 SYNC Move cursor to AISHUT, press ENTER key to enter SETUP MENU [1/5] SETUP MENU [2/5] This function is used to adjust phase of external sync. AISHUT FUNCTION SELECTING menu, then Press UP or When input external sync, we can press ENTER key to CAMERA ID WHITE BAL AWB. - Page 33 7.2 AWB 4.2 AES AUTO MODE Move cursor to WHITE BAL, press ENTER key to enter Move cursor to AES, press ENTER key to enter AES SETUP MENU [2/5] SETUP MENU [1/5] WHITE BAL FUNCTION SELECTING menu, then Press FUNCTION SELECTING menu, then Press UP or DOWN →AWB.
-
Page 34: White Balance
7 WHITE BALANCE Press ENTER key to set BLC AREA BLOCK. Press UP or DOWN key to select BLC AREA BLOCK. 7.1 ATW SETUP MENU [2/5] Move cursor to WHITE BAL, press ENTER key to enter WHITE BAL FUNCTION SELECTING menu, then Press →ATW.