Table of Contents
Advertisement
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/tool/battery must be placed in a well
ventilated area when charging.
The charger is intended for indoor use only.
Electrical safety
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains voltage
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Warning! Never attempt to replace the charger unit with
a regular mains plug.
Features
1. On/off switch
2. Lock-off button
3. Blade release button
4. Shear blade
5. Trim blade
6. Charging indicator
Assembly
Warning! Avoid accidentally switching the tool on during
assembly.
Fitting the wall mount to the wall (fig. A & B)
The wall mount can be fitted to the wall to provide a
convenient storage and charging point for the tool.
Drive the screws in the wall through the holes in the
crevices of wall mount.
Place the tool on the wall mount.
Plug in the charger making sure the charging indicator (6)
lights up (fig. A).
If required, use the two pegs (7) below the wall mount to
store the spare blade (fig. B).
Warning! Avoid damaging the power cord when mounting the
wall mount to the wall.
Removing the charger plug from the wall mount
(fig. C)
The tool can be charged without using the wall mount. The
charger plug can be connected to the tool directly.
Remove the screws from the back of the wall mount.
Slide the back part (8) from the front part (9) to open the
wall mount.
8
Remove the charger plug from the wall mount.
Fitting and removing the blade (fig. D & E)
The shear blade (4) has been designed for trimming grass
and weeds. The trim blade (5) has been designed for trimming
hedges and shrubs.
Note: Before fitting the blade apply a small amount of grease
to the drive slot of the blade from the sachet provided.
Remove the blade cover.
Push and hold the blade release button (3) in the direction
of the arrow (fig. D1).
Slide the blade cover (10) backward and lift off (fig. D2).
Place the blade under edge marked 'X' (fig. E1) at the
angle as shown and then lower the blade onto the pins.
While holding the blade onto the pins (fig. E2), replace the
blade cover (10) and slide it forward (fig. E3).
Note: No alignment of blade with drive pin is required and
operation of the blade cover release button is not required
when re-fitting the blade cover.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. When charging the battery for the first
time, or after prolonged storage, it will only accept an 80%
charge. After several charge and discharge cycles, the battery
will attain full capacity. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
The tool can be left connected to the charger indefinitely.
To maximise the lifetime of the battery, it is recommended to
keep the battery connected to the charger whenever the tool
is not in use. When the battery is full, the power consumption
of the charger is negligible.
Charging with the wall mount (fig. F)
Place the tool on the wall mount (11).
Plug in the charger.
Charging with the charger plug (fig. G)
The charger plug is designed with lock outs to prevent the use
of an incorrect charger.
Insert the charger plug (12) into the charger connector at
the rear of the tool.
Plug in the charger.
Hide quick links:
Advertisement
Table of Contents
