Black & Decker KR508 Linea PRO Instruction Manual page 3

ENGLISH
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power
tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly maintained power tools.
f. Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
6. Electrical Safety
Your tool is double insulated; therefore no earth wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally qualified person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified person, but not authorized by Black & Decker, the
warranty will not be valid.
7. Labels on Tool
The label on your tool may include the following symbols:
Read Instruction Manual
Use Eye Protection
Use Ear Protection
V...............................Volts
A.............................. Amperes
Hz............................ Hertz
W..............................Watts
min...........................minutes
...........................Alternating current
...........................Direct current
n ............................. No load speed
0
...........................Class II Construction
...........................Earthing terminal
...........................Safety alert symbol
.../min...................... Revolutions or reciprocations
per minute
4
ADDITIONAL SAFETY INSTRUCTIONS
FOR IMPACT DRILLS
• Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.
• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping surfaces when performing an operation where the cutting
accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and shock the operator.
• Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and may lead to loss of control.
• Before drilling into walls, floors or ceilings, check for the location of wiring and pipes.
• Avoid touching the tip of a drill bit just after drilling, as it may be hot.
VIBRATION
The declared vibration emission values stated in the technical data and the declaration of conformity have been
measured in accordance with a standard test method provided by EN 60745 and may be used for comparing one tool
with another.
WARNING:
The vibration emission value during actual use of the power tool can differ from the declared value
depending on the ways in which the tool is used. The vibration level may increase above the level stated.
FEATURES
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ASSEMBLY
WARNING:
Before assembly, make sure that the tool is switched off and unplugged.
FITTING THE SIDE HANDLE AND DEPTH STOP (FIG. A)
• Turn the grip counterclockwise until you can slide the side handle (7) onto the front of the tool as shown.
• Rotate the side handle into the desired position.
• Insert the depth stop (6) into the mounting hole as shown.
• Set the drilling depth as described below.
• Tighten the side handle by turning the grip clockwise.
KEYED CHUCK (FIG. B)
• Open the chuck by turning the sleeve (9) counterclockwise.
• Insert the bit shaft (8) into the chuck.
• Insert the chuck key (10) into each hole (11) in the side of the chuck and turn clockwise until tight.
REMOVING AND REFITTING THE CHUCK (FIG. C)
• Slacken the side handle (8) by turning the grip counterclockwise.
ENGLISH
5