Operating and installation instructions Cooker hood DA 3360 en - GB To avoid the risk of accidents or damage to this appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 09 190 840...
Caring for the environment Disposal of the packing material Disposal of your old appliance The packaging is designed to protect Electrical and electronic appliances the appliance from damage during often contain valuable materials. They transportation. The packaging materials also contain materials which, if handled used are selected from materials which or disposed of incorrectly, could be are environmentally friendly for...
It must only be used as a domestic appliance to extract vapours and remove odours from cooking. Any other usage is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation.
Technical safety Installation, maintenance and repairs may only be carried out by a Before installation, check the cooker Miele authorised person in accordance hood for visible signs of damage. with current national and local safety Under no circumstances should you regulations.
Warning and Safety instructions Do not connect the appliance to the Using at the same time as other mains electricity supply by a heating appliances that depend on multi-socket adapter or an extension the air from the room lead. These do not guarantee the required safety of the appliance (e.g.
Warning and Safety instructions In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously, an underpressure of 0.04 mbar (4 pa) is the maximum permissible in the room.
Warning and Safety instructions Correct use The cooker hood can get very hot during cooking due to heat rising from Do not use an open flame beneath the hob. the cooker hood. To avoid the danger Do not touch the housing or the grease of fire, do not flambé...
Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves. All ducting, pipework and fittings must be of non-flammable material. These can be obtained from the Miele Spare Parts department or from builders' merchants. The appliance must not be connected to a chimney or vent flue which is in use.
Guide to the appliance / Operation a Exhaust socket Depending on the intensity of the cooking vapours, levels "1" to "3" are C 150 mm usually sufficient for normal cooking. b Controls For short periods of strong vapours and c Grease filter cooking odours, e.g.
Charcoal filters are available to order socket in the motor unit. through your Dealer / Chartered Agent or the Miele Spare Parts Department or Having a non-return flap fitted in the via the internet at www.miele-shop.com. ducting ensures that air, once ducted...
(This infomation does not apply to the controls). Stainless steel surfaces can be cleaned using the Miele E-Cloth or with a Housing suitable, non-abrasive, proprietary cleaning agent for stainless steel, General following the manufacturer's instructions on the packaging.
Cleaning and care Controls The controls may suffer discolouration or damage if soiling is left on them for too long. Remove soiling straight away. Observe the General notes on cleaning earlier in this section. When removing the grease filter do not tilt it downwards at an angle.
Make sure that the spray arm can move freely. ^ Select a programme with a maximum temperature of 65° C. If a Miele dishwasher is being used, select the ^ When putting it back, make sure that Sensor wash programme.
It is fitted in the canopy above the grease filter. Replacement charcoal filters can be obtained from your dealer, Miele or via the internet at www.miele-shop.com. See back cover for contact details, and "Technical data" for type and reference number.
Cleaning and care Changing a halogen lamp ^ Pull out the deflector plate, and remove the grease filter as described earlier. ^ Switch off the fan and the lighting. Exercise caution when changing halogen lamps. They get very hot during use, and remain hot for some time after being switched off.
For information on the appliance under guarantee, please contact: guarantee specific to your country – Your Miele Dealer / Chartered Agent please contact Miele. See back cover for contact details. In the U.K. your appliance is –...
650 mm above gas hobs and cookers 650 mm If this cooker hood is installed above a Miele Wok CS 1028 CombiSet appliance, a minimum safety distance of 760 mm must be maintained between the burner and the lower edge of the cooker hood.
Installation a 1 exhaust socket for exhaust ducting C 150 mm. b 1 reducing collar 12 screws 4 x 15 mm for C125 mm exhaust ducting. for securing the cooker hood into the c 1 non-return flap wall unit. for fitting into the exhaust socket (for air extraction mode only).
Installation Positioning the appliance in the wall housing unit To position the appliance correctly, cut the spacer strip to required depth T, and then attach it to the back of the appliance. T= Depth of carcase K minus depth of ^ Screw the spacer strip underneath appliance G the housing unit sides, flush with the...
Installation Do not remove the protective film between the deflector plate and the ^ Screw the brackets onto the right and casing until the hood has been placed in the housing unit. left inside walls of the housing unit as shown.
Installation Note for dismantling the cooker hood: Undoing the screws on the left and right inside the housing releases the spring mounts, allowing the appliance to be removed from the unit. ^ Lift the appliance up into the housing from below until it engages in the brackets.
Installation Attaching the lightshield ^ Attach the lightshield (if using). A DML 400 installation kit, available as ^ Remove the protective film between an optional accessory, is required for this. the deflector plate and the casing. Follow the installation instructions ^ Secure the front of the appliance to supplied.
Installation Aligning the deflector plate Fitting the grease filter ^ Remove the protective strip around the edge of the grease filter. Fit the grease filter. ^ To do this, pull the deflector plate out. ^ The position of the deflector plate can be brought forward by up to 35 mm using the adjusting screws on either side of the deflector plate.
Installation Vent ducting ^ If the on-site ventilation system does not have a non-return flap, then the non-return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit. ^ When using C 150 mm ducting, secure the exhaust socket supplied to the exhaust ducting with hose clips.
^ Connect the appliance to the electricity supply. For this, conversion kit DUU 151 (available from your Miele dealer or the Miele Spare Parts Department) is required. You will also need a charcoal filter (see...
Connection for air extraction – Where ducting is horizontal, it must Important: To avoid the danger of be laid to slope away at at least 1 cm toxic fumes, please observe the per metre. This is to ensure that Warning and Safety instructions. condensate cannot drain back into This is especially crucial when using the cooker hood.
Connection for air extraction Condensate trap (optional accessory) In addition to insulating the exhaust ducting, we recommend that a suitable condensate trap is also installed to collect and evaporate any condensate which may occur. Condensate traps are available for C 125 mm or C 150 mm ducting.
Connection for air extraction Silencer (optional accessory) ...with air extraction: The silencer not only reduces noise from the fan, but also sounds from outside (e.g. traffic noise). To achieve even further reductions in For this reason the silencer must be noise levels, a special silencer can be positioned as close as possible to where fitted in the ducting system.
Electrical connection If the switch is not accessible after All electrical work should be installation (depending on country), an undertaken by a suitably qualified additional means of disconnection must and competent person in strict be provided for all poles. accordance with current national For extra safety it is advisable to protect and local safety regulations the appliance with a suitable residual...