Dimplex CKHA Installation Instructions

1-888-346-7539
1-888-346-7539
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Notes
Notes
Care must be taken to prevent undue strain on all
Care must be taken to prevent undue strain on all
wiring or heating element assembly, when removing
wiring or heating element assembly, when removing
and re-assembling heating element assembly.
and re-assembling heating element assembly.
For field rewiring to 120V all leads must be secured
For field rewiring to 120V all leads must be secured
under wire clamps.
under wire clamps.
Air and grille temperatures conform to CSA & UL
Air and grille temperatures conform to CSA & UL
regulations but may discolour certain materials,
regulations but may discolour certain materials,
particularly those materials incorporating clear vinyl.
particularly those materials incorporating clear vinyl.
Materials should be checked prior to installation to
Materials should be checked prior to installation to
determine if discolouration or distortion would occur
determine if discolouration or distortion would occur
in the vicinity of 60°C (140° F)
in the vicinity of 60°C (140° F)
General
General
To prepare the unit for installation, first check that
To prepare the unit for installation, first check that
heater nameplate voltage is the same as electrical
heater nameplate voltage is the same as electrical
service.
service.
Kickspace Installation
Kickspace Installation
NOTE - Unit should be installed so that it is not directly under sink or other frequently used work area as air temperature
NOTE - Unit should be installed so that it is not directly under sink or other frequently used work area as air
may be uncomfortably warm. Also, if carpeting is on floor, mount unit so bottom of grille is level or above the top of the
temperature may be uncomfortably warm. Also, if carpeting is on floor, mount unit so bottom of grille is level or
carpet pile.
above the top of the carpet pile.
1. Measure area of intended use. If there is not
1. Measure area of intended use. If there is not
sufficient room for the grille frame, the frame may
sufficient room for the grille frame, the frame may
be removed by removing grille frame from heater
be removed by removing grille frame from heater
(screw "A"), remove frame and re-insert grille.
(screw "A"), remove frame and re-insert grille.
2. Cut 22 3/8" x 3 5/8" opening (Fig.2). Keep
2. Cut 22 3/8" x 3 5/8" opening (Fig.2). Keep
clearance area free of obstructions.
clearance area free of obstructions.
3. Bring in service cable to left or rear of 10" minimum
3. Bring in service cable to left or rear of 10" minimum
area as shown in Fig.2.
area as shown in Fig.2.
4. Remove heater cover and appropriate knockout.
4. Remove heater cover and appropriate knockout.
Attach service cable to unit with approved
Attach service cable to unit with approved
connector and connect colour to colour in outlet
connector and connect colour to colour in outlet
box. To change wattage or voltage connections,
box. To change wattage or voltage connections,
see Fig.4.
see Fig.4.
5. Replace cover, slide unit into opening, and secure
5. Replace cover, slide unit into opening, and secure
each side (Fig.1).
each side (Fig.1).
NOTE - Make sure unit is installed right side up.
NOTE - Make sure unit is installed right side up.
Refer to "TOP" label.
Refer to "TOP" label.
6. For inspection of field wiring, see instruction under "Electrical Inspection".
6. For inspection of field wiring, see instruction under "Electrical Inspection".
WARNING - Hazzard of severe shock
WARNING - Hazard of severe shock
CAUTION - Disconnect all power coming to heater at main
CAUTION - Disconnect all power coming to heater at main
service panel before wiring or servicing.
service panel before wiring or servicing.
Kickspace Heater
MODEL CKHA/RKHA
HEATER COVER
HEATER COVER
TOP LABEL
TOP LABEL
JUNCTION BOX COVER
JUNCTION BOX COVER
SCREW 'C' SCREW "C"
SCREW 'A'
SCREW "A"
SERVICE
WIRES
3" MAX.
22"
KNOCKOUT
Kickspace Heater
MODEL 610048000
HEATER
HEATER
ELEMENT
ELEMENT
SCREW 'B'
SCREW "B"
GRILLE
GRILLE
TRIM FRAME
TRIM FRAME
10" MIN.
22 3/8"
3 1/2"
9 1/2"
7200960100R05
Fig. 1
Fig. 1
Fig. 2
Fig. 2