Summary of Contents for Black Box ServPower Omni PS730A
Page 1
Order toll-free in the U.S.: 877-877-BBOX (outside U.S. call 724-746-5500) SUPPORT FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 INFORMATION Web site: www.blackbox.com • E-mail: info@blackbox.com...
Page 3
ServPower Omni FCC STATEMENT Philippines FEDERAL COMMUNICATIONS COMMISSION Portugal Slovak Republic Spain CANADIAN DEPARTMENT OF COMMUNICATIONS Sweden Switzerland RADIO FREQUENCY INTERFERENCE STATEMENTS Taiwan United Kingdom This equipment generates, uses, and can radiate radio frequency energy United States and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
Page 4
ServPower Omni Appendix B: Modem Certifications Normas Oficiales Mexicanas (NOM) Modem Certifications Electrical Safety Statement The following countries have certified the internal modem. In order to comply with local regulations, the countrycode must be set to the INSTRUCCIONES DE SEGURIDAD country of installation.
Page 5
ServPower Omni NOM STATEMENT 11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo PSE723 2 x C20 8 x C13 I, S del tipo descrito en el instructivo de operación, o como se indique en el aparato. PSE724 2 x C20 8 x C13...
ServPower Omni Appendix A: Specifications Specifications Physical: Height: 1U 1.75 in (4.5 cm) Width: 19.0 in (48.25 cm) Depth: 6.00 in (15.25 cm) Weight: 7 lbs (3.25 Kg) Temperature Operating: 0 to 40 Storage: -10 to 85 Relative 0 to 95% Humidity Non-Condensing Input Required...
ServPower Omni CHAPTER 1: Quick Start The ServPower Omni can provide Secure Socket Layer (SSL) encryption 1. Quick Start on the web interface. Enable this feature using the set web ssl yes command from the Telnet / Serial interface. 7.5 Email Notification Email can be automatically sent for outlet changes, AutoPing triggers and current alarms.
ServPower Omni CHAPTER 7: Advanced Features 2. General Overview Select from CTION None AutoPing not used The ServPower Omni series is designed to provide power distribution and On – Latch Upon triggering, ServPower Omni will power on remote power control. Each ServPower Omni allows eight outlets to be the assigned outlet and remain so until changed via independently switched on and off for reboot, energy management and the web or telnet/serial interface.
ServPower Omni CHAPTER 3: Installation Notes: 3. Installation Not issuing a command for 5 seconds will cause the ServPower Omni to hang 3.1 Rack Mounting The only outlets that a caller has access to are determined by the CLI command The ServPower Omni is designed for mounting in a standard 19”...
ServPower Omni CHAPTER 7: Advanced Features 3.3 Serial Port 7. Advanced Features The ServPower Omni has a 9 pin D subminiature connector for RS-232 serial control. The connector is configured as DCE for direct connection to a laptop or other terminal device. Default serial parameters are 115,200 7.1 DTMF Control bps, 8 data, no parity, 1 stop bit (115200,8,n,1).
ServPower Omni CHAPTER 3: Installation 6.6 Group Commands 3.5 Expansion For future applications. get groups Returns a list of groups Returns a list of outlets in a get group <name> group 3.6 Power Source set group <name> The ServPower Omni models PS730A and PS730A-M provide a linecord Sets a group’s name <on/off/cycle>...
Page 14
ServPower Omni CHAPTER 7: Advanced Features 6.5 User Commands The ServPower Omni models PS723 and PS724 provide two IEC 320 universal inlet for connecting a detachable power cord. A standard IEC to CEE7 European cord set is supplied with the unit for use on 16 Amp The following commands require administrative rights 240VAC service*.
ServPower Omni CHAPTER 4: Initial Configuration 4. Initial Configuration set time zone <time zone -12 to 13> 4.1 Accessing the Command Line Interface set time hour <0-23> All configuration parameters are set using the Command Line Interface set time minute <0-59> (CLI).
Page 16
ServPower Omni CHAPTER 7: Advanced Features If you wish to prevent DHCP or ARP-Ping from altering the IP Address, also enter the following command set snmp writecommunity 32 characters max <name> set ipmode static Changing any of these values will require a reboot of the unit. Type the set snmp readcommunity 32 characters max command “reboot”...
Page 17
If the ServPower Omni fails to respond, repeat steps 2-4 above. If the defaults port to SSL standard problem persists, contact Black Box Tech Support. 443. Setting to no requires http:// access and defaults Unix, Linux, MAC and others port to HTTP standard 80.
ServPower Omni CHAPTER 7: Advanced Features 6.3 Outlet Commands 5. Web Operation Returns the status of each get outlets outlet the user has rights to. 5.1 Web Interface get outlet <n> Returns the status of outlet n Commands outlet n to power set outlet <n>...
ServPower Omni CHAPTER 6: CLI Operation 38400, 57600, 115200 on the On, Off, or Cycle button. Cycle will perform a timed change in outlet state (either Reboot for On-Off-On, or Cycle Off-On-Off) Returns all modem parameters get modem depending on the current state of the outlet. Set the country code.
ServPower Omni CHAPTER 7: Advanced Features 6.3 Device Commands 6. CLI Operation Each ServPower Omni can have get device name a name assigned. 20 6.1 Command Line Interface characters Max, no spaces. set device name <name> The Command Line Interface follows a set/get syntax similar to SNMP. Returns the current draw for get current each Main in Amperes...