Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt XR Li-ION DCD932
Summary of Contents for DeWalt XR Li-ION DCD932
- Page 1 DCD932 DCD937 DCD990 DCD995...
- Page 2 Dansk (oversat fra original brugsvejledning) Deutsch (übersetzt von den Originalanweisungen) English (original instructions) Español (traducido de las instrucciones originales) Français (traduction de la notice d’instructions originale) Italiano (tradotto dalle istruzioni originali) Nederlands (vertaald vanuit de originele instructies) Norsk (oversatt fra de originale instruksjonene) Português (traduzido das instruções originais) Suomi (käännetty alkuperäisestä...
- Page 3 Figure 1 DCD990 Figure 2...
- Page 4 Figure 3 Figure 4 Figure 5 Figure 7 Figure 6 Figure 8 Figure 9...
-
Page 5: Technical Data
EN GL IS H BRUSHLESS CORDLESS 13 mm (12") DRILL/DRIVER, DCD932, DCD990 BRUSHLESS CORDLESS 13 mm (12") DRILL/DRIVER/HAMMERDRILL, DCD937, DCD995 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make WALT one of the most reliable partners for professional power tool users. -
Page 6: Defi Nitions: Safety Guidelines
EN GLI SH Vibration emission value a Screwdriving m/s² < 2.5 < 2.5 < 2.5 < 2.5 Uncertainty K = m/s² An estimation of the level of exposure to The vibration emission level given in this information vibration should also take into account sheet has been measured in accordance with a the times when the tool is switched off standardised test given in EN 60745 and may be... -
Page 7: Ec Declaration Of Conformity
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed DCD932, DCD937, DCD990, DCD995 (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of WALT declares that these products described electric shock. - Page 8 EN GLI SH Prevent unintentional starting. Ensure Keep cutting tools sharp and clean. the switch is in the off position before Properly maintained cutting tools with sharp connecting to power source and/or cutting edges are less likely to bind and are battery pack, picking up or carrying the easier to control.
-
Page 9: Residual Risks
EN GL IS H • Use clamps or other practical way to secure Important Safety Instructions for All and support the workpiece to a stable Battery Chargers platform. Holding the work by hand or against your body is unstable and may lead to loss of SAVE THESE INSTRUCTIONS: This manual control. -
Page 10: Charging Process
EN GLI SH • When operating a charger outdoors, always charger. The red (charging) light will blink provide a dry location and use an extension continuously indicating that the charging cord suitable for outdoor use. Use of a cord process has started. suitable for outdoor use reduces the risk of 3. -
Page 11: Important Safety Instructions For All Battery Packs
Battery Pack • DO NOT splash or immerse in water or other BATTERY TYPE liquids. The DCD932 and DCD937 operate on 14.4 volt • Do not store or use the tool and battery battery packs. pack in locations where the temperature The DCD990 and DCD995 operate on 18 volt may reach or exceed 40 °C (105 °F) (such as... -
Page 12: Package Contents
EN GLI SH 2 14.4 V Li-Ion battery packs (DCD932, DCD937) 2 18 V Li-Ion battery packs (DCD990, DCD995) Read instruction manual before use. 1 Kitbox 1 Charger 1 Side handle Charging. 1 Instruction manual Fully charged. 1 Exploded drawing NOTE: Battery packs, chargers and kitboxes are not Hot/cold pack delay. -
Page 13: Electrical Safety
EN GL IS H supervised by a person responsible for their TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE safety. Children should never be left alone with 1. Align the battery pack (h) with the rails inside the this product. tool’s handle (fig. - Page 14 EN GLI SH If model is not equipped with side handle, grip drill Speed 2 (middle torque and speed setting) is in the with one hand on the handle and one hand on the middle position. Speed 3 (highest speed setting) is battery pack.
- Page 15 EN GL IS H Belt Hook and Magnetic Bit Holder Proper hand position requires one hand on the main handle (n), with the other hand on the side handle (fi g. 1) (g). WARNING: To reduce the risk of Drill Operation (fi g. 4) serious personal injury, turn tool WARNING: To reduce the risk off and disconnect battery pack...
-
Page 16: Maintenance
EN GLI SH depth. The lower the number, the lower the torque output. 2. Reset the torque adjustment collar (e) to the Lubrication appropriate number setting for the torque desired. Make a few practice runs in scrap or Your power tool requires no additional lubrication. unseen areas to determine the proper position of the torque adjustment collar. -
Page 17: Rechargeable Battery Pack
EN GL IS H Should you find one day that your D WALT product GUARANTEE needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this WALT is confident of the quality of its product available for separate collection. - Page 18 06126-21-1 Richard Klinger Str. 11 Fax: 06126-21-2770 65510 Idstein www.dewalt.de Ελλάς Black & Decker (Ελλάς) Α.Ε. Τηλ: 30 210 8981-616 www.dewalt.gr Στράβωνος 7 & Βουλιαγμένης 159 Service: 30 210 8981-616 Γλυφάδα 16674, Αθήνα Φαξ: 30 210 8983-570 España WALT Tel: 934 797 400 Parque de Negocios “Mas Blau”...