Page 1
Service Manual AOCi2252VW LCD 显示器维修手册 Custom: Model: i2252VW 本手册适用于主板为 715G4502,Scalar IC NT68660 This manual applies to mainboard 715G4502,Scalar IC NT68660...
Service Manual AOCi2252VW REVISION LIST Revision Editor Model Version Release Date TPV Model No History Jun-28-2011 Initial Release AOCi2252VW TIBGN22YAYA1HNJ TPV-BJ-Rainsun...
Service Manual AOCi2252VW 1. LCD Specifications 1.1 Product Features Monitor Model AOC i2252VW Driving system TFT Color LCD Active Display Area 476.64mm (W)×268.11mm(H) 546.86mm diagonal LCD Panel Pixel Pitch 0.24825 mm×0.24825mm R,G,B Analog Interface,75ohm,0.7V Video DVI digital Interface Input Separate Sync.
Service Manual AOCi2252VW 1.4 VGA 15pin Connector Pin No. Description Pin No. Description Red Input +5VDC Green Input Logic GND Blue Input SDA- DDC-Serial Data Connection detect H Sync Red GND V Sync Green GND SCL- DDC-Serial Clock Blue GND VGA Connector layout 1.5 DVI Connector Pin No.
Service Manual AOCi2252VW 2. Operation instruction 2.1 Connection Connect the video cable from the video card of PC to the monitor.. The power cord should be connected Press the power button to turn on the monitor, the power indicator will light up. ...
Service Manual AOCi2252VW 2.3 OSD User mode adjustment a) OSD Menu adjustment steps: +/ - 1. Press MENU to activate OSD main menu, Touch button may select other Menu item.. +/ - 2. Press MENU button to select items of each main menu.Touch to move and select.
Service Manual AOCi2252VW 2.4 OSD Locked When press “ ” to switched on the monitor, while holding press the” menu” button, the menu will be locked. Again, the OSD menu is non-locked.
Service Manual AOCi2252VW 3. Panel Feature LM215WF3 is a Color Active Matrix Liquid Crystal Display with a Light Emitting Diode ( White LED) backlight system without LED driver. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode.
Service Manual AOCi2252VW 4.4 Software Flow Chart Start Software Flow Chart Initial_MCU To Write default values Check if DataBuffer Is blank Check if Sum is changed ? Brightness Contrast Read parameter_from Buffer Language InputType InputTimingStableCounter OsdCounter Init_GlobalVariables PowerDownCounter Initial_MCU Device while PowerHandler if standby mode?
Service Manual AOCi2252VW 8.3 Trouble Shooting Main Board--- No Power No power Check flow chart For the no power Press power key and look if the picture is normal Please reinsert and make sure the AC 100-240V is normal ? Reinsert or check the power section Check 5V-CN404, 3.3V-U404-2;...
Page 39
Service Manual AOCi2252VW No picture (LED orange) No picture Check flow chart for the no signal Check signal wire Replace signal wire Check U404 Vout=3.3V; Q409-out=1.8V replaceU404,Q409,Q410,Q405 &around device check X401 waveform replace X401 Check CN101-RGB/HS/VS Check Correspondent component Check U402/U403 out Updata soft data Replace U401 Whitescreen...
Page 40
Service Manual AOCi2252VW Power Board--- No Power 5V/12V Check flow chart Check CN901 100-240V? For the no power Check AC supply Check rectified voltage-C907 checkFuseF901/ rectified device L902/BD901/C901/C902 Check voltage of IC901-8pin check component R904/R932 Check T901(1-3)out-Vcc Check D901/R909/C903 Check IC901-drive out Check/replace IC901 Check MOS-Q901pin(G/D) Check R910/R938/Q901/T901pri...
Page 41
Service Manual AOCi2252VW No Backlight of panel Check flow chart for the Check voltage of F801-12V? Inverter No Backlight Open F801, voltage-12V Return check Power Check ON/OFFsignal After Power off,check Check main board C801/C802?Q824? Check IC801 -12pin=12V pinRT waveform? After Power off,check Q805/Q808/R804/C825 Check IC801-6pin RT waveform? Check aroud component...
Page 42
Service Manual AOCi2252VW Key Board--- OSD no working Check flow chart OSD is unstable or not For the key board working Connect Key Pad Board Is Key Pad Board connecting normally? Is Button Switch normally? Replace Button Switch Is Key Pad Board normally? Replace Key Pad Board Check Main Board...
Service Manual AOCi2252VW 8.4 Software update step Product information 756GJBCB AA025 MCU ASS'Y main board CBPCAN2A1J1 U402 056G2233501 FLASH MX25L2026DM1I-12G 2Mb SOP-8 SMTCA-U402 100GANGI000B11 AOC_i2252Vwe_Nt68660_LGD_LM215WF3-SLC1 U401 056G 562369 SCALER NT68660UFG/B TQFP-100 Step1:Connection 1. Connect one end of the USB line cable to the PC, the other to connect the ISP tool(715GT089-B ) ; 2.
Page 45
Service Manual AOCi2252VW Step3:Run 1.To Run TOOL : In the "Start" – ”program "in the writer icon, , as shown , “ “ 2.Click “Option” FE2P Mode Enable” TOOL 默认为 √”, withhold HDCP KEY, select “setup ISP tool”,---“FTDI”,”Confirm Change”,The figuer is as follows...
Page 47
Service Manual AOCi2252VW Click “Option”,select WP pin, The figuer is as follows...
Page 48
Service Manual AOCi2252VW 4.click “ISP ON”, The figuer is as shown,OK ; 5.Click “ ”, “Load File” Find software file, The figuer is as follows...
Service Manual AOCi2252VW 6.Click“Auto”, Start Programming, until the successful ;The figuer is as follows 8.5 Re-Writing DDC program step After replacing the Main board and the Panel, Check if white-balance is within the specs ,then re-writing DDC is necessary. 1. Prepared the PC with Windows XP system, DDC recording device (12V)for figure below 2.
Service Manual AOCi2252VW 8.6 Factory mode adjustment After replacing the Main board and the Panel, Check for enter the Factory mode ,then re-writing DDC is necessary. Step: In normal display mode, unplug the power cord to shut down。Then Press “MENU” button and hold, At the same time plug the power cord to turned on the Power , Then, click the menu button,the monitor will may enter Factory OSD Menu.
Service Manual AOCi2252VW 9.BOM List Note: The parts information listed below are for reference only, and are subject to change without notice. Please go to http://cs.tpv.com.cn/hello1.asp for the latest information. 9.1 Model:TIBGN22YAYA1HNJ Location Part number Description Remark 040G 581689 4A BARCODE LABEL FOR 1 Conductive Tape 85mm *40mm *0.09mm (单导) 052G...
Page 55
Service Manual AOCi2252VW C927 067G215S3316KV EC 330uF M 35V 10*12mm C907 067G215S3316LV EC 330uF 35V M 10*12.5mm 2nd source C908 067G215S3316LV EC 330uF 35V M 10*12.5mm 2nd source C927 067G215S3316LV EC 330uF 35V M 10*12.5mm 2nd source L901 073G 174192 H LINE FILTER 30MH MIN LCL-12012 HA L901 073G 174192 X...