Supero SUPERSERVER 1027TR-TF User Manual
  1. Manuals
  2. Brands
  3. Supero Manuals
  4. Server
  5. SUPERSERVER 1027TR-TF
  6. User manual

Supero SUPERSERVER 1027TR-TF User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S
UPER
S
UPER
S
UPER
S
UPER
USER'S MANUAL
S
ERVER
S
ERVER
S
ERVER
Revision 1.0
1027TR-TF
1027TR-TFF
1027TR-TQF
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SUPERSERVER 1027TR-TF and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Supero SUPERSERVER 1027TR-TF

Summary of Contents for Supero SUPERSERVER 1027TR-TF

  • Page 1 UPER ® 1027TR-TF UPER ERVER 1027TR-TFF UPER ERVER 1027TR-TQF UPER ERVER USER’S MANUAL Revision 1.0...
  • Page 2 The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.

  • Page 3: About This Manual

    It provides information for the installation and use of the SuperServer 1027TR- TF/1027TR-TFF/1027TR-TQF. Installation and maintenance should be performed by experienced technicians only. The SuperServer 1027TR-TF/1027TR-TFF/1027TR-TQF is a 1U Twin (two server- boards in a 1U chassis) rackmount server based on the CSE-809BTS-1K28BP chassis and two Super X9DRT-F/X9DRT-IBFF/X9DRT-IBQF serverboards.
  • Page 4 Chapter 4: System Safety You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SuperServer 1027TR-TF/1027TR-TFF/1027TR-TQF. Chapter 5: Advanced Serverboard Setup Chapter 5 provides detailed information on the X9DRT-F/X9DRT-IBFF/X9DRT-IBQF serverboard, including the locations and functions of connectors, headers and jump- ers.

  • Page 5: Table Of Contents

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Table of Contents Chapter 1 Introduction Overview ......................1-1 Serverboard Features ..................1-2 Processors ...................... 1-2 Memory ......................1-2 Onboard Serial ATA ..................1-2 PCI Expansion Slots ..................1-2 Ethernet Ports ....................1-2 Onboard Controllers/Ports ................1-3 Graphics Controller ..................
  • Page 6 Table of Contents Identifying the Sections of the Rack Rails ............2-4 Installing the Rack Rails ................. 2-5 Installing the Server into a Rack ..............2-7 Installing the Server into a Telco Rack ............2-8 Checking the Serverboard Setup ..............2-9 Preparing to Power On .................
  • Page 7 Onboard Indicators ..................5-25 5-12 PCI-Express and Serial ATA Connections ............ 5-26 5-13 Installing Additional Drivers ................5-27 5-14 Configuring Supero Doctor III ............... 5-28 5-15 Onboard Battery .................... 5-30 Chapter 6 Advanced Chassis Setup Static-Sensitive Devices .................. 6-1 Precautions ..................... 6-1 Unpacking .......................
  • Page 8 Table of Contents Starting BIOS Setup Utility ................7-1 How To Change the Configuration Data ............7-1 Starting the Setup Utility ................. 7-2 Main Setup ...................... 7-2 Advanced Setup Configurations..............7-3 Event Logs ....................7-25 IPMI ....................... 7-28 Boot ....................... 7-30 Security ......................

  • Page 9: Chapter 1 Introduction

    Chapter 1 Introduction Overview The SuperServer 1027TR-TF/1027TR-TFF/1027TR-TQF is a "1U Twin" server comprised of the CSE-809BTS-1K28BP 1U chassis and two (twin) X9DRT-F/ X9DRT-IBFF/X9DRT-IBQF serverboards. Please refer to our web site for information on operating systems that have been certified for use with the 1027TR-TF/1027TR- TFF/1027TR-TQF (www.supermicro.com).

  • Page 10: Serverboard Features

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Serverboard Features At the heart of the SuperServer 1027TR-TF/1027TR-TFF/1027TR-TQF lies two X9DRT-F/X9DRT-IBFF/X9DRT-IBQF dual processor serverboards, which are based on Intel's E5-2600 (Socket R LGA 2011) chipset. Below are the main features of the serverboards. Note that the features on each board are doubled for the server, which includes two nodes.

  • Page 11: Onboard Controllers/Ports

    Chapter 1: Introduction Onboard Controllers/Ports Onboard I/O backpanel ports on each serverboard include one COM port, a VGA port, two USB ports, a dedicated IPMI LAN port and two Gigabit LAN (NIC) ports. An InfiniBandport is also included on the X9DRT-IBFF/X9DRT-IBQF serverboards. There are two sets of I/O ports included in the server (one set for each serverboard).

  • Page 12: System Block Diagram

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual CPU FRONT FAN Side Socket 2 E5-2600 CPU REAR (I/O Side) Socket 1 E5-2600 Gen3 Gen3 Gen3 x8(8..15) AT25321 FDR/QDR SATA3 #5 SATA3 #4 SATA2 #3 SATA2 #2 SATA SATA3 #1 6/3/1.5 I350 SATA3 #0 2 ports PEG0 C602J...

  • Page 13: Server Chassis Features

    1U chassis. Details on the chassis can be found in Chapter 6. System Power When configured as a SuperServer 1027TR-TF/1027TR-TFF/1027TR-TQF, the CSE-809BTS-1K28BP includes a single high-efficiency (Gold Level) 1280W cold- swap power supply, which provides the power to both serverboards housed in the chassis.

  • Page 14: Twin: System Notes

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual 1U Twin: System Notes As a 1U Twin configuration, the 1027TR-TF/1027TR-TFF/1027TR-TQF is a unique server system. With two nodes incorporated into a single chassis, there are several points you should keep in mind. System Power A single power supply is used to provide the power for both serverboards.

  • Page 15: Contacting Supermicro

    Chapter 1: Introduction Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel:...
  • Page 16 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Notes...

  • Page 17: Chapter 2 Server Installation

    Chapter 2: Server Installation Chapter 2 Server Installation Overview This chapter provides a quick setup checklist to get your server system up and running. Following these steps in the order given should enable you to have the system operational within a minimum amount of time. This quick setup assumes that your system has come to you with the processors and memory preinstalled.

  • Page 18: Warnings And Precautions

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual • This product is for installation only in a Restricted Access Location (dedicated equipment rooms, service closets and the like). • This product is not suitable for use with visual display work place devices accord- ing to §2 of the the German Ordinance for Work with Visual Display Units.

  • Page 19: Rack Mounting Considerations

    Chapter 2: Server Installation • Always keep the rack's front door and all panels and components on the servers closed when not servicing to maintain proper cooling. • Make sure all power and data cables are properly connected and not blocking the chassis airflow.

  • Page 20: Installing The Server Into A Rack

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Warning! To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: •...

  • Page 21: Installing The Rack Rails

    Chapter 2: Server Installation Figure 2-1. Identifying the Sections of the Rack Rails (right side rail shown) Inner Rail - Preattached to the Chassis Inner Rail Extension - Attach to the Chassis Outer Rack Rails - Attach to the Rack Installing the Rack Rails The SC809 chassis includes a set of inner rack rails in two sections: inner rails (A) and inner rail extensions (B).
  • Page 22 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Figure 2-2: Installing the Inner Rail Extensions Inner Rail Extension Inner Rail Preattached to the Chassis Installing the Outer Rails to the Rack 1. Attach the short bracket to the outside of the long bracket. You must align the pins with the slides.

  • Page 23: Installing The Server Into A Rack

    Chapter 2: Server Installation Figure 2-3: Assembling the Outer Rails Outer Rail Secure to the Front of the Rack Secure to the Rear of the Rack Secure Outer Rails Together Installing the Server into a Rack 1. Confirm that chassis includes the inner rails (attached to the chassis beneath the rail extentions) and rail extensions (B).

  • Page 24: Installing The Server Into A Telco Rack

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Figure 2-4: Installing the Rack Rails Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over.

  • Page 25: Checking The Serverboard Setup

    Chapter 2: Server Installation Checking the Serverboard Setup After you install the server in the rack, you will need to open the top cover to make sure the serverboard is properly installed and all the connections have been made. Accessing the Inside of the System (Figure 2-5) To access the system, first grasp the two handles on either side and pull the system straight out until it locks (you will hear a "click").

  • Page 26: Preparing To Power On

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Preparing to Power On Next, you should check to make sure the peripheral drives and the SATA drives and backplane have been properly installed and all connections have been made. Checking the SATA drives The SATA disk drives are accessable from the front of the server and can be installed and removed from the front of the chassis without removing the top chassis cover.
  • Page 27 Chapter 2: Server Installation Figure 2-5. Accessing the Inside of the System Remove these screws Remove this screw Remove this screw 2-11...

  • Page 28: Chapter 3 System Interface

    Chapter 3: System Interface Chapter 3 System Interface Overview There are several LEDs on the two control panels and on the hard drive carriers to keep you constantly informed of the overall status of the system as well as the activ- ity and health of specific components.

  • Page 29: Control Panel Leds

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Control Panel LEDs Each of the two control panels located on the front of the SC809 chassis has five LEDs. Each LED provides you with critical information related its own specific serverboard. This section explains what each LED indicates when illuminated and any corrective action you may need to take.

  • Page 30: Power

    Chapter 3: System Interface Power Indicates power is being supplied to the system's power supply unit. This LED should normally be illuminated when the system is operating. Drive Carrier LEDs Each hard drive carrier has two LEDs. • Green: When illuminated, the green LED on the front of the drive carrier indi- cates drive activity.
  • Page 31 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Notes...

  • Page 32: About Standardized Warning Statements

    Chapter 4: Warning Statements for AC Systems Chapter 4 Standardized Warning Statements for AC Systems About Standardized Warning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance.
  • Page 33 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut.
  • Page 34 Warning Statements for AC Systems ‫جسذٌة‬ ‫اصابة‬ ً‫تتسبب ف‬ ‫حالة ٌوكي أى‬ ً‫اًك ف‬ ‫خطز‬ ًٌ‫ٌع‬ ‫هذا الزهز‬ !‫تحذٌز‬ ‫الذوائز‬ ‫بالوخاطز الٌاجوة عي‬ ‫ي على علن‬ ، ‫ك‬ ‫هعذات‬ ‫تعول على أي‬ ‫قبل أى‬ ‫الكهزبائٍة‬ ‫حىادث‬ ‫أي‬ ‫وقىع‬ ‫وٌع‬ ‫ل‬ ‫الىقائٍة‬...

  • Page 35: Installation Instructions

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Installation Instructions Warning! Read the installation instructions before connecting the system to the power source. 設置手順書 システムを電源に接続する前に、 設置手順書をお読み下さい。 警告 将此系统连接电源前,请先阅读安装说明。 警告 將系統與電源連接前，請先閱讀安裝說明。 Warnung Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.

  • Page 36: Circuit Breaker

    Chapter 4: Warning Statements for AC Systems Circuit Breaker Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V, 20 A. サーキッ ト ・ ブレーカー この製品は、 短絡 （過電流） 保護装置がある建物での設置を前提としています。 保護装置の定格が250 V、...

  • Page 37: Power Disconnection Warning

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual 경고! 이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다. Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 220V, 20A.
  • Page 38 Chapter 4: Warning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema. Attention Le système doit être débranché...

  • Page 39: Equipment Installation

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Equipment Installation Warning! Only trained and qualified personnel should be allowed to install, replace, or service this equipment. 機器の設置 トレーニングを受け認定された人だけがこの装置の設置、 交換、 またはサービスを許可 されています。 警告 只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。 警告 只有經過受訓且具資格人員才可安裝、更換與維修此設備。 Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden.

  • Page 40: Restricted Area

    Chapter 4: Warning Statements for AC Systems Waarschuwing Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door geschoold en gekwalificeerd personeel. Restricted Area Warning! This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

  • Page 41: Battery Handling

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual ‫אזור עם גישה מוגבלת‬ !‫אזהרה‬ ‫יש להתקין את היחידה באזורים שיש בהם הגבלת גישה. הגישה ניתנת בעזרת‬ .)'‫כלי אבטחה בלבד (מפתח, מנעול וכד‬ ‫محظورة‬ ‫مناطق‬ ٍ‫نتركُبها ف‬ ‫هذه انىحذة‬ ‫تخصيص‬ ‫تم‬ ،‫أداة خاصت‬ ‫من خالل استخذاو‬ ‫فقط‬...
  • Page 42 Chapter 4: Warning Statements for AC Systems Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant.

  • Page 43: Redundant Power Supplies

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Redundant Power Supplies Warning! This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. 冗長電源装置 このユニッ トは複数の電源装置が接続されている場合があります。 ユニッ トの電源を切るためには、 すべての接続を取り外さなければなりません。 警告 此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。 警告 此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。 Warnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

  • Page 44: Backplane Voltage

    Chapter 4: Warning Statements for AC Systems ‫امداد الطاقة‬ ‫بوحدات‬ ‫عدة اتصاالت‬ ‫جهاز‬ ‫ال‬ ‫يكون لهذا‬ ‫قد‬ ‫الكهرباء‬ ‫عن‬ ‫وحدة‬ ‫ال‬ ‫لعسل‬ ‫كافة االتصاالت‬ ‫يجب إزالة‬ 경고! 이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에 전원을...

  • Page 45: Comply With Local And National Electrical Codes

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual ‫מתח בפנל האחורי‬ !‫הרה‬ ‫אז‬ ‫קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת. יש להיזהר במהלך‬ .‫העבודה‬ ‫اللىحة‬ ‫أوالطاقة المىجىدة على‬ ‫التيار الكهزبائي‬ ‫مه‬ ‫خطز‬ ‫هناك‬ ‫هذا الجهاس‬ ‫خدمة‬ ‫كه حذرا عند‬ ‫يعمل‬ ‫النظام‬ ‫عندما يكىن‬ 경고! 시스템이...

  • Page 46: Product Disposal

    Chapter 4: Warning Statements for AC Systems Attention L'équipement doit être installé conformément aux normes électriques nationales et locales. ‫תיאום חוקי החשמל הארצי‬ !‫אזהרה‬ ‫הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬ ‫התקנת‬ ‫المتعلقة‬ ‫المحلية والىطىية‬ ‫قىاويه‬ ‫يجب أن يمتثل لل‬ ‫الكهربائية‬...

  • Page 47: Hot Swap Fan Warning

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
  • Page 48 Chapter 4: Warning Statements for AC Systems 警告 當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Warnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt. ¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador del chasis.

  • Page 49: Power Cable And Ac Adapter

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Power Cable and AC Adapter Warning! When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any other electrical devices than products designated by Supermicro only.
  • Page 50 Chapter 4: Warning Statements for AC Systems Attention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné. L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit l'utilisation de UL ou CSA câbles certifiés qui ont UL ou CSA indiqué...
  • Page 51 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Notes 4-20...

  • Page 52: Chapter 5 Advanced Serverboard Setup

    Chapter 5: Advanced Serverboard Setup Chapter 5 Advanced Serverboard Setup This chapter covers the steps required to install the X9DRT-F/X9DRT-IBFF/X9DRT- IBQF serverboard into the CSE-809BTS-1K28BP chassis, connect the data and power cables and install add-on cards. All serverboard jumpers and connections are also described.

  • Page 53: Unpacking

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Unpacking The serverboard is shipped in antistatic packaging to avoid electrostatic discharge. When unpacking the board, make sure the person handling it is static protected. Serverboard Installation This section explains the first step of physically mounting the X9DRT-F/X9DRT- IBFF/X9DRT-IBQF into the CSE-809BTS-1K28BP chassis.

  • Page 54: Connecting Cables

    Chapter 5: Advanced Serverboard Setup Warning: To avoid damaging the motherboard and its components, do not apply any force greater than 8 lbs. per square inch when installing a screw into a mount- ing hole. Connecting Cables Now that the serverboards are installed, the next step is to connect the cables to the boards.

  • Page 55: I/O Ports

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Figure 5-1. Control Panel Header Pins x (Key) x (Key) Power On LED 3.3V HDD LED Front UID Button NIC1 LED (Link) NIC1 LED (Activity) NIC2 LED (Link) NIC2 LED (Activity) OH/Fan Fail/Pwr Fail/UID LED UID LED Power Fail LED 3.3V...

  • Page 56: Processor And Heatsink Installation

    Chapter 5: Advanced Serverboard Setup Processor and Heatsink Installation When handling the processor package, avoid placing direct pressure on the label area of the fan. Notes: • Always connect the power cord last and always remove it before adding, re- moving or changing any hardware components.
  • Page 57 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual 1. Using your thumb and the index finger, remove the 'WARNING' plastic cap from the socket. 2. Use your thumb and index finger to hold the CPU on its edges. Align the CPU keys which are semi-circle cutouts, against the socket keys.
  • Page 58 Chapter 5: Advanced Serverboard Setup 3. Once they are aligned, carefully lower the CPU straight down into the socket. (Do not drop the CPU on the socket. Do not move the CPU horizontally or vertically. Do not rub the CPU against the surface or against any pins of the socket to avoid damaging the CPU or the socket.) Warning: You can only install the CPU inside the socket in one direction.

  • Page 59: Identifying A Heatsink

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Identifying a Heatsink Two types of heatsinks (SNK-P0047PW and SNK-P0047PS) are used in 1027TR-TF/1027TR-TFF/1027TR-TQF. Be careful with its own proper instal- lation location. See the figure below for their locations. SNK-P0047PW SNK-P0047PS CPU 1 CPU 2...

  • Page 60: Installing A Cpu Heatsink

    Chapter 5: Advanced Serverboard Setup Installing a CPU Heatsink 1. Remove power from the system and unplug the AC power cord from the power supply. 2. Do not apply any thermal grease Screw #1 Screw #2 to the heatsink or the CPU die; the required amount has already been applied.

  • Page 61: Removing The Heatsink

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Removing the Heatsink Warning! We do not recommend that the CPU or the heatsink be removed. However, if you do need to uninstall the heatsink, please follow the instructions below to prevent damage to the CPU or the CPU socket.

  • Page 62: Installing Memory

    Chapter 5: Advanced Serverboard Setup Installing Memory CAUTION! Exercise extreme care when installing or removing DIMM modules to prevent any possible damage. Memory Support Each X9DRT-F/X9DRT-IBFF/X9DRT-IBQF up to 256 GB of 240-pin Registered (RDIMM)/Load Reduced (LRDIMM) ECC or up to 64 GB of Unbuffered (UDIMM) ECC/Non-ECC DDR3 1600/1333/1066/800 MHz 4-channel memory in 8 slots.
  • Page 63 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Installing UDIMM (ECC/Non-ECC) Memory Intel E5-2600 Series Processor UDIMM Memory Support Ranks Per DIMM & Memory Capacity Speed (MT/s) and Voltage Validated by Slot per Data Width Per DIMM Channel (SPC) and DIMM Per Channel (DPC) 1 Slot Per Channel (See the Note below) 1DPC...

  • Page 64: Adding Pci Cards

    Chapter 5: Advanced Serverboard Setup Installing LRDIMM (ECC) Memory Intel E5-2600 Series Processor LRDIMM Memory Support Ranks Per Memory Capacity Speed (MT/s) and Voltage Validated by Slot DIMM & Data Per DIMM per Channel (SPC) and DIMM Per Channel Width (DPC) 1 Slot Per Channel (See the Note...

  • Page 65: Serverboard Details

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Serverboard Details Figure 5-4. X9DRT Series Motherboard Layout CPU FRONT FAN Side Socket 2 E5-2600 CPU REAR (I/O Side) Socket 1 E5-2600 Gen3 Gen3 Gen3 x8(8..15) AT25321 FDR/QDR SATA3 #5 SATA3 #4 SATA2 #3 SATA2 #2 SATA SATA3 #1 6/3/1.5...

  • Page 66: X9Drt-F/X9Drt-Ibff/X9Drt-Ibqf Quick Reference

    Chapter 5: Advanced Serverboard Setup X9DRT-F/X9DRT-IBFF/X9DRT-IBQF Quick Reference Jumper Description Default Setting JBT1 CMOS Clear (See Section 5-10) JIB1 InfiniBand Enable (X9DRT-IBQF/-IBFF) Pins 1-2 (Enabled) C1/JI SMB to PCI-E Slots Open (Normal) JPB1 BMC Enable Pins 1-2 (Enabled) JPG1 VGA Enable Pins 1-2 (Enabled) JPL1 LAN1/LAN2 Enable...

  • Page 67: Connector Definitions

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Connector Definitions ATX Power 20-pin Connector Pin Definitions (ATX Power 1/2) Pin# Definition Pin # Definition Power Connectors Ground PS_On_N Two 20-pin main power supply con- Ground 5V_STBY nectors (J23/ J24) and a 4-pin power Ground Ground connector (JP8) are located on the...
  • Page 68 Chapter 5: Advanced Serverboard Setup PW_ON Connector Power Button Pin Definitions (JF1) The PW_ON connector is on pins 1 and 2 of JF1. Pin# Definition This header should be connected to the chassis PW_ON power button. See the table on the right for pin Ground definitions.
  • Page 69 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual NIC1 (LAN1) LED NIC1 LED Pin Definitions (JF1) The NIC (Network Interface Controller) Pin# Definition LED connections for GLAN port 1 are NIC 2 Activity LED located on pins 11 and 12 of JF1, and NIC 2 Link LED the LED connection for GLAN Port 2 are on Pins 9 and 10.

  • Page 70: Serial Ports

    Chapter 5: Advanced Serverboard Setup Serial Ports Serial Port Pin Definitions (COM1/COM2) The COM1 serial port is located beside Pin # Definition Pin # Definition the VGA port. Refer to the motherboard layout for the location of the COM2 header. See the table on the right for pin definitions.
  • Page 71 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual IPMB I C SMB SMB Header (JIPMB1) Pin Definitions A System Management Bus header for Pin# Definition the IPMI slot is located at JIPMB1. Con- Data nect an appropriate cable here to use Ground the IPMB I C connection on your system.
  • Page 72 Chapter 5: Advanced Serverboard Setup Ethernet LAN Ports LAN Ports (LAN1/2) Pin Definition Two Gigabit Ethernet ports (LAN1/2) Pin# Definition Pin# Definition are located on the I/O backplane on P2V5SB SGND the motherboard. In addition, an IPMI TD0+ Act LED Dedicated LAN is located above USB 0/1 ports on the backplane to provide TD0-...
  • Page 73 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Unit Identifier Switches UID Switch Two Unit Identifier (UID) Switches and Pin# Definition two LED Indicators are located on the Ground motherboard. The Front Panel UID Ground Switch is located at Pin 16 on JF2. The Button In Rear UID Switch is located at SW1 next Ground...

  • Page 74: 5-10 Jumper Settings

    Chapter 5: Advanced Serverboard Setup 5-10 Jumper Settings To modify the operation of the serverboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two Connector pins to change the function of the Pins connector. Pin 1 is identified with a square solder pad on the printed circuit board.
  • Page 75 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Watch Dog Enable/Disable JWD1 enables the Watch Dog func- Watch Dog Jumper Settings (JWD1) tion, a system monitor that takes action Jumper Setting Definition when a software application freezes Pins 1-2 Reset the system. Jumping pins 1-2 will Pins 2-3 have Watch Dog reboot the system if a Open...

  • Page 76: 5-11 Onboard Indicators

    Chapter 5: Advanced Serverboard Setup 5-11 Onboard Indicators Activity LED Link LED GLAN LEDs The Gigabit LAN ports are located on the IO Rear View (when facing the Backplane on the motherboard. Each Ether- rear side of the chassis) net LAN port has two LEDs. The Yellow LED GLAN Activity Indicator (Left) LED Settings indicates activity.

  • Page 77: 5-12 Pci-Express And Serial Ata Connections

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual BMC Heartbeat LED BMC Heartbeat LED Status A BMC Heartbeat LED is located at Color/State Definition LEM1 on the motherboard. When LEM1 Green: BMC: Normal is blinking, BMC functions normally. See Blinking the table at right for more information. InfiniBand Link LED (LEB1) Settings IB LED Indicators (X9DRT-IBQF+/IBFF...

  • Page 78: 5-13 Installing Additional Drivers

    Chapter 5: Advanced Serverboard Setup 5-13 Installing Additional Drivers After you've installed the Windows Operating System, a screen as shown below will appear. You are now ready to install software programs and drivers that have not yet been installed. To install these software programs and drivers, click the icons to the right of these items.

  • Page 79: Configuring Supero Doctor Iii

    The Supero Doctor III program is a Web-based management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called the SD III Client. The Supero Doctor III program included on the CDROM that came with your motherboard allows you to monitor the environment and operations of your system.
  • Page 80 Chapter 5: Advanced Serverboard Setup Note: SD III Software Revision 1.0 can be downloaded from our Web site at: ftp:// ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's Guide at: http://www.supermicro.com/manuals/other/SDIII_User_Guide.pdf. For Linux, we will still recommend that you use Supero Doctor II. 5-29...

  • Page 81: 5-15 Onboard Battery

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual 5-15 Onboard Battery Serverboard Battery: CAUTION - There is a danger of explosion if the onboard battery is installed upside down, which will reverse its polarites (see the figure below). This battery must be replaced only with the same or an equivalent type recommended by the manufacturer (CR2032).
  • Page 82 Chapter 5: Advanced Serverboard Setup Notes 5-31...

  • Page 83: Chapter 6 Advanced Chassis Setup

    Chapter 6: Advanced Chassis Setup Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform mainte- nance on the CSE-809BTS-1K28BP chassis. For component installation, follow the steps in the order given to eliminate the most common problems encountered. If some steps are unnecessary, skip ahead to the step that follows.

  • Page 84: Control Panel

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Figure 6-1. Chassis Front View Control Panel: Primary Serverboard Control Panel: Secondary Serverboard SATA Drives Figure 6-2. Chassis Rear View Dedicated IPMI Port PCI-Exp x16 Slot Dedicated IPMI Port PCI-Exp x16 Slot LAN Ports Power Supply...

  • Page 85: System Fans

    Chapter 6: Advanced Chassis Setup System Fans Each serverboard has its own set of three 4-cm high-performance PWM fans (for a total of six in the chassis) to provide the cooling for the system. Fan speed may be controlled by a setting in BIOS (see Chapter 7). System Fan Failure If a fan fails, the remaining fans will ramp up to full speed and the overheat/fan fail LED on the control panel will blink on and off.

  • Page 86: Air Shrouds

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Figure 6-3: Replacing a System Fan Air Shrouds Air shrouds concentrate airflow to maximize fan efficiency. The SC809 chassis air shroud does not require screws to set up. Two identical air shrouds are needed in the system, one for each node.

  • Page 87: Drive Bay Installation/Removal

    Chapter 6: Advanced Chassis Setup Figure 6-4: Installing the Air Shrouds Drive Bay Installation/Removal Accessing the Drive Bays SATA Drives: Because of their hotswap capability, you do not need to access the inside of the chassis or power down the system to install or replace SATA drives. Proceed to the next step for instructions.
  • Page 88 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual SATA Drive Installation The SATA drives are mounted in drive carriers to simplify their installation and removal from the chassis. These carriers also help promote proper airflow for the system. For this reason, even empty carriers without drives installed must remain in the chassis.

  • Page 89: Power Supply

    Chapter 6: Advanced Chassis Setup Figure 6-6. Removing a Drive Power Supply The 1027TR-TF/1027TR-TFF/1027TR-TQF has a single 1280 watt power supply. This power supply has the capability of operating at 100 - 240 input volts. Power Supply Failure If the power supply unit fails, the system will shut down and you will need to replace the power supply unit.
  • Page 90 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual 4. Pull the power supply out using the handle provided. 5. Push the new power supply module into the power bay until it clicks into place. 6. Plug the AC power cord back into the module and power up the server by pushing the power on buttons for both nodes..

  • Page 91: Chapter 7 Bios

    Chapter 7: BIOS Chapter 7 BIOS Introduction This chapter describes the AMI BIOS Setup utility for the X9DRT-F/X9DRT-IBFF/ X9DRT-IBQF. It also provides the instructions on how to navigate the AMI BIOS Setup utility screens. The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated.

  • Page 92: Starting The Setup Utility

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Starting the Setup Utility Normally, the only visible Power-On Self-Test (POST) routine is the memory test. As the memory is being tested, press the <Delete> key to enter the main menu of the AMI BIOS Setup utility. From the main menu, you can access the other setup screens.

  • Page 93: Advanced Setup Configurations

    Chapter 7: BIOS Supermicro X9DRT Version This item displays the SMC version of the BIOS ROM used in this system. Build Date This item displays the date that the BIOS Setup utility was built. Memory Information Total Memory This displays the amount of memory that is available in the system. Advanced Setup Configurations Select the Advanced tab to access the following submenu items.
  • Page 94 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual This feature allows the user to select bootup screen display between POST mes- sages and the OEM logo. Select Disabled to display the POST messages. Select Enabled to display the OEM logo instead of the normal POST messages. The op- tions are Enabled and Disabled.

  • Page 95: Power Configuration

    Chapter 7: BIOS as bootable disks. If this item is set to Disabled, the ROM BIOS of the host adap- tors will not capture Interrupt 19, and the drives attached to these adaptors will not function as bootable devices. The options are Enabled and Disabled. Re-try Boot When set to Enabled, the BIOS will continuously retry to boot from the selected boot type.
  • Page 96 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual • Type of CPU • CPU Signature • Microcode Patch • CPU Stepping • Maximum CPU Speed • Minimum CPU Speed • Processor Cores • Intel HT (Hyper-Threading) Technology • Intel VT-x Technology • Intel SMX Technology •...
  • Page 97 Chapter 7: BIOS Hyper-threading Select Enabled to support Intel Hyper-threading Technology to enhance CPU per- formance. The options are Enabled and Disabled. Active Processor Cores Set to Enabled to use a processor's second core and above. (Please refer to Intel's website for more information.) The options are All, 1, 2, 4, and 6.

  • Page 98: Cpu Power Management Configuration

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Select Enabled for DCU (Data Cache Unit) IP Prefetcher support, which will prefetch IP addresses to improve network connectivity and system performance. The options are Enabled and Disabled. Intel Virtualization Technology (Available when supported by the CPU) ®...
  • Page 99 Chapter 7: BIOS CPU C6 Report (Available when Power Technology is set to Custom) Select Enabled to allow the BIOS to report the CPU C6 State (ACPI C3) to the operating system. During the CPU C6 State, the power to all cache is turned off.

  • Page 100: Chipset Configuration

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Short Duration Power Limit This item displays the time period during which short duration power (in watts) is maintained. The default setting is 0. Chipset Configuration North Bridge This feature allows the user to configure the settings for the Intel North Bridge.

  • Page 101: Qpi Configuration

    Chapter 7: BIOS Port 1B Link Speed Select GEN1 to enable PCI-Exp Generation 1 support for the port. Select GEN2 to enable PCI-Exp Generation 2 support for the port. Select GEN3 to enable PCI-Exp Generation 3 support for the port. The options are GEN1, GEN2, and GEN3.
  • Page 102 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Current Memory Mode This item displays the current memory mode. Current Memory Speed This item displays the current memory speed. Mirroring This item displays if memory mirroring is supported by the motherboard. Memory mirroring creates a duplicate copy of the data stored in the memory to enhance data security.

  • Page 103: South Bridge Configuration

    Chapter 7: BIOS Channel Interleaving This feature selects from the different channel interleaving methods. The options are Auto, 1 Way, 2 Way, 3, Way, and 4 Way. Rank Interleaving This feature allows the user to select a rank memory interleaving method. The options are Auto, 1 Way, 2 Way, 4, Way, and 8 Way.

  • Page 104: Sata Configuration

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Name: This item displays the name of the PCH chip. Stepping: This item displays the status of the PCH stepping. USB Devices: This item displays the USB devices detected by the BIOS. All USB Devices This feature enables all USB ports/devices. The options are Disabled and Enabled.
  • Page 105 Chapter 7: BIOS IDE Mode The following items are displayed when IDE Mode is selected: Serial-ATA (SATA) Controller 0~1 Use this feature to activate or deactivate the SATA controller, and set the compatibility mode. The options are Disabled, Enhanced, and Compatible. The default for SATA Controller 0 is Compatible.
  • Page 106 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual PCI Latency Timer Use this feature to set the latency Timer of each PCI device installed on a PCI bus. Select 64 to set the PCI latency to 64 PCI clock cycles. The options are 32, 64, 96, 128, 160, 192, 224 and 248.

  • Page 107: Super Io Configuration

    Chapter 7: BIOS Onboard LAN Option ROM Select Select iSCSI to use the iSCSI Option ROM to boot the computer using a network device. Select PXE (Preboot Execution Environment) to use an PXE Option ROM to boot the computer using a network device. The options are iSCSI and PXE. Load Onboard LAN1 Option ROM, Load Onboard LAN2 Option ROM Select Enabled to enable the onboard LAN1/LAN2 Option ROM.

  • Page 108: Serial Port Console Redirection

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Device Mode Use this feature to select the desired mode for a serial port specified. The options are Normal and High Speed. SOL Configuration Serial Port Select Enabled to enable a serial port specified by the user. The options are Enabled and Disabled.

  • Page 109: Console Redirection Settings

    Chapter 7: BIOS Console Redirection Select Enabled to use the SOL Port for Console Redirection. The options are Enabled and Disabled. Console Redirection Settings This feature allows the user to specify how the host computer will exchange data with the client computer, which is the remote computer used by the user. Terminal Type This feature allows the user to select the target terminal emulation type for Con- sole Redirection.
  • Page 110 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Flow Control This feature allows the user to set the flow control for Console Redirection to prevent data loss caused by buffer overflow. Send a "Stop" signal to stop send- ing data when the receiving buffer is full. Send a "Start" signal to start sending data when the receiving buffer is empty.

  • Page 111: Acpi Settings

    Chapter 7: BIOS Console Redirection (for EMS) Select Enabled to use a COM Port selected by the user for Console Redirection. The options are Enabled and Disabled. Console Redirection Settings (for EMS)  This feature allows the user to specify how the host computer will exchange data with the client computer, which is the remote computer used by the user.
  • Page 112 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual ACPI Sleep State Use this feature to select the ACPI State when the system is in sleep mode. Select S1 (CPU Stop Clock) to erase all CPU caches and stop executing instructions. Power to the CPU(s) and RAM is maintained, but RAM is refreshed. Select Sus- pend Disabled to use power-reduced mode.
  • Page 113 Chapter 7: BIOS Note: During restart, the computer will reboot in order to execute the pend- ing operation and change the state of the security device. Current Status Information: This item displays the information regarding the current TPM status. TPM Enable Status This item displays the status of TPM Support to indicate if TPM is currently enabled or disabled.

  • Page 114: Iscsi Configuration

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual VT-d Support: Intel Virtualization Technology with Direct I/O support VT Support: Intel Virtualization Technology support TPM Support: Trusted Platform support TPM State: Trusted Platform state ME Subsystem This feature displays the following ME Subsystem Configuration settings.

  • Page 115: Nic Configuration

    Chapter 7: BIOS NIC Configuration Link Speed Use this feature to change the link speed and duplex for the current port. The op- tions are AutoNeg, 10Mbps Half, 10Mbps Full, 100Mbps Half, and 100Mbps full. Wake on LAN Select enabled to wake the system with a magic packet. The options are En- abled and Disabled.

  • Page 116: Change Smbios Event Log Settings

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Change SMBIOS Event Log Settings  This feature allows the user to configure SMBIOS Event settings. Enabling/Disabling Options SMBIOS Event Log Select Enabled to enable SMBIOS (System Management BIOS) Event Logging during system boot. The options are Enabled and Disabled.
  • Page 117 Chapter 7: BIOS Select Enabled to erase the SMBIOS (System Management BIOS) Event Log, which is completed before a event logging is initialized upon system reboot. The options are No, Yes, Next reset, and Yes, Every reset. When Log is Full Select Erase Immediately to immediately erase SMBIOS error event logs that ex- ceed the limit when the SMBIOS event log is full.

  • Page 118: Ipmi

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual IPMI Select the IPMI (Intelligent Platform Management Interface) tab to access the fol- lowing submenu items. IPMI Firmware Revision, IPMI Status These items indicates your system IPMI firmware revision number and status. System Event Log ...

  • Page 119: Bmc Network Configuration

    Chapter 7: BIOS Custom EFI Logging Options Log EFI Status Codes Select Enabled to log EFI (Extensible Firmware Interface) Status Codes, Error Codes or Progress Codes. The options are Enabled and Disabled. Note: After making changes on a setting, be sure to reboot the system for the changes to take effect.

  • Page 120: Boot

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Boot This submenu allows the user to configure the following boot settings for the system. Boot Option Priorities Boot Option #1/ Boot Option #2/ Boot Option #3, etc. Use this feature to specify the sequence of boot device priority.

  • Page 121: Security

    Chapter 7: BIOS Security This menu allows the user to configure the following security settings for the system. Password Check Use this feature to determine when a password entry is required. Select Setup to require the password only when entering setup. Select Always to require the pass- word when entering setup and on each boot.

  • Page 122: Save & Exit

    SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Save & Exit This submenu allows the user to configure the Save and Exit settings for the system. Discard Changes and Exit Select this option to quit the BIOS Setup without making any permanent changes to the system configuration, and reboot the computer. Select Discard Changes and Exit, and press <Enter>.
  • Page 123 Chapter 7: BIOS Discard Changes Select this feature and press <Enter> to discard all the changes and return to the BIOS setup. When the dialog box appears, asking you if you want to load previ- ous values, select Yes to load the values previous saved, or select No to keep the changes you've made so far.
  • Page 124 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Notes 7-34...

  • Page 125: Appendix A Bios Error Beep Codes

    Appendix A: BIOS Error Beep Codes Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process.
  • Page 126 SUPERSERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Notes...

  • Page 127: Appendix B System Specifications

    Appendix B: System Specifications Appendix B System Specifications Processors Four Intel® 5500 Series processors in LGA1366 sockets Note: please refer to our website for details on supported processors. Chipset Intel 5520/ICH10R BIOS 32 Mb AMI SPI Flash ROM Memory Capacity Twelve DIMM sockets that can support up to 192 GB of ECC registered (or 48 GB of unbuffered) DDR3-1333/1066/800 SDRAM (384 or 96 GB for the system) Note: interleaved memory requires DIMMs to be installed in pairs - refer to Section 5-6 for details.

  • Page 128: System Cooling

    UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual Weight Gross Weight: 40 lbs. (18.2 kg.) System Cooling Six (6) high-performance 4-cm PWM (Pulse Width Modulated) fans System Input Requirements AC Input Voltage: 100 - 240V AC auto-range Rated Input Current: 13 - 4A max Rated Input Frequency: 50 to 60 Hz Power Supply Rated Output Power: 1200W (Part# PWS-1K21P-1R)
  • Page 129 Appendix B: System Specifications Notes...
  • Page 130 UPER ERVER 1027TR-TF/1027TR-TFF/1027TR-TQF User's Manual (continued from front) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency com- munication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage.

This manual is also suitable for:

Superserver 1027tr-tffSuperserver 1027tr-tqf

Table of Contents