Nilfisk-Advance AquaRide Service Manual
  1. Manuals
  2. Brands
  3. Nilfisk-Advance Manuals
  4. Scrubber
  5. AquaRide
  6. Service manual
Nilfisk-Advance AquaRide Service Manual

Nilfisk-Advance AquaRide Service Manual

Advance models 56314008, 56314009 nilfisk models 56314019
Hide thumbs
Table of Contents

Advertisement

Quick Links

A A A A A quaRide
quaRide
quaRide
quaRide
quaRide
BR
BR
X 700
X 700
BR
BR X 700
BR
X 700
X 700
SERVICE MANUAL
SERVICE MANUAL
SERVICE MANUAL
SERVICE MANUAL
SERVICE MANUAL
Advance MODELS 56314008, 56314009
Advance MODELS 56314008, 56314009
Advance MODELS 56314008, 56314009
Advance MODELS 56314008, 56314009
Advance MODELS 56314008, 56314009
Nilfisk MODELS 56314019
Nilfisk MODELS 56314019
Nilfisk MODELS 56314019
Nilfisk MODELS 56314019
Nilfisk MODELS 56314019
™ ™ ™ ™ ™
/AquaRide
/AquaRide
/AquaRide
/AquaRide
/AquaRide
™ ™ ™ ™ ™
S E
S E
S E
S E
S E
5/03 Form Number 56043089

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AquaRide and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Nilfisk-Advance AquaRide

Summary of Contents for Nilfisk-Advance AquaRide

  • Page 1 ™ ™ ™ ™ ™ ™ ™ ™ ™ ™ A A A A A quaRide quaRide quaRide /AquaRide /AquaRide quaRide /AquaRide quaRide /AquaRide /AquaRide X 700 X 700 BR X 700 X 700 X 700 SERVICE MANUAL SERVICE MANUAL...

  • Page 2: Table Of Contents

    VACUUM MOTOR(S) REMOVAL ............................. 45 RECOVERY TANK REMOVAL ............................45 RECOVERY TANK BLADDER REMOVAL ........................46 RECOVERY TANK BLADDER INSTALLATION ....................... 46 VACUUM SHOES REMOVAL FOR MAINTENANCE ..................... 48 78 78 78 78 78 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 3 WIRING DIAGRAM ................................79 Note: Note: Note: All references to right, left, front, or rear in this manual are as seen from the operator’s stand-point. Note: Note: FORM NO. 56043089 / AquaRide ™ / BRX 700 - 1 1 1 1 1...

  • Page 4: General Information

    INTRODUCTION INTRODUCTION This manual will help you get the most from your Nilfisk-Advance Rider Extractor. Read it thoroughly before servicing the machine. Note: Bold numbers and letters in parentheses and underlined indicate an item illustrated on pages 9-10 i.e. ( Note: Bold numbers and letters in parentheses and underlined indicate an item illustrated on pages 9-10 i.e.

  • Page 5: Safety Instructions

    CAUTIONS AND WARNINGS CAUTIONS AND WARNINGS SYMBOLS SYMBOLS SYMBOLS SYMBOLS SYMBOLS Nilfisk-Advance uses the symbols below to signal potentially dangerous conditions. Always read this information carefully and take the necessary steps to protect personnel and property. DANGER! DANGER! DANGER! DANGER! DANGER! Is used to warn of immediate hazards that will cause severe personal injury or death.

  • Page 6: Specifications & Maintenance

    **Gross Weight: Standard machine without options, full solution tank and empty recovery tank, with removable scrub brushes and 305 AH batteries. ***Listings for watts are maximum values. 4 4 4 4 4 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 7 SPECIFICA SPECIFICATIONS SPECIFICA TIONS TIONS TIONS SPECIFICA SPECIFICA TIONS Chassis Width Width with deck TOP VIEW Height Length RIGHT SIDE VIEW FORM NO. 56043089 / AquaRide ™ / BRX 700 - 5 5 5 5 5...
  • Page 8 Check the brush(s) daily. Remove any built-up string, hair or carpet fibers. Check the bristle length. Have a service technician change the brush(s) when the brush bristles are worn to 1 inch (25mm). 6 6 6 6 6 - FORM NO. 56043089 / AquaRide ™...

  • Page 9: Pm Checklist

    Recovery Tank Cover Gasket Recovery Tank Drain Hose & Cap Flush Vacuum Pick-Up Tool & Hoses Back flush Page 1 of 2 Copyright 2003 Nilfisk-Advance. 2/21/2001 FORM NO. 56043089 / AquaRide ™ / BRX 700 - 7 7 7 7 7...
  • Page 10 W worn out leaks WORK COMPLETED BY: ACKNOWLEDGED BY: Service Technician Signature Date Customer Signature Date Page 2 of 2 Copyright 2003 Nilfisk-Advance. 2/21/2001 8 8 8 8 8 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 11: Know Your Machine

    26 26 26 26 26 Tie Down Locations (3) Tie Down Locations (3) Tie Down Locations (3) Tie Down Locations (3) Emergency Stop Switch / Battery Disconnect Tie Down Locations (3) FORM NO. 56043089 / AquaRide ™ / BRX 700 - 9 9 9 9 9...
  • Page 12 Solution System Indicator Solution System Indicator Solution System Indicator Solution System Indicator R R R R R Solution Switch Solution Switch Solution Switch Solution Switch Solution Switch 10 10 10 10 10 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 13 Solution Control Valve (25 25 25 25 25) ) ) ) ) – This valve should be fully open whenever extracting. Only close this valve before removing the solution Solution Control Valve ( Solution Control Valve ( filter to prevent loss of solution. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 11 11 11 11 11...
  • Page 14 If the maintenance mode is selected, pressing this switch will select the restoration mode. If the restoration mode is already selected, pressing this switch will have no effect. 12 12 12 12 12 - FORM NO. 56043089 / AquaRide ™...
  • Page 15 The solution flow will only turn on when the throttle is moved from the neutral position in the forward direction. The solution flow will turn off if the throttle returns to neutral or is moved to reverse. FORM NO. 56043089 / AquaRide ™...
  • Page 16 Power Saving Sleep Function The AquaRide / BRX 700 is equipped with a battery saving feature that will turn all of the machine systems and accessories off if the machine is left in an idle state for a preset period of time. This sleep mode will only occur if the operator is not on the seat and the wand function is not in use.
  • Page 17 K1 K1) ) ) ) ) . A fully charged battery pack ™ will measure above 37.6 volts with no load applied (2.09 volts per cell). The AquaRide / BRX 700 is equipped with a low voltage cutout feature that will turn the scrub system off when the batteries are discharged to their minimum level. There are two different cutout levels to accommodate different battery types.

  • Page 18: Steering System

    Grip the shroud and pull up to completely release it from the steering column base and the foot brake assembly. FIGURE 1 FIGURE 1 FIGURE 1 FIGURE 1 FIGURE 1 Remove plug to access/grease universal joint View from back side of panel (I) FRONT 16 16 16 16 16 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 19: Steering Chain Removal And Tensioning

    Keep all of the steer chain links oiled to prevent excessive wear and binding. FIGURE 2 FIGURE 2 FIGURE 2 FIGURE 2 FIGURE 2 View from under the machine FRONT FORM NO. 56043089 / AquaRide ™ / BRX 700 - 17 17 17 17 17...

  • Page 20: Wheel Drive System

    The following is a list of the speed control parameters that can be adjusted using a Curtis hand held programmer: There are four programmable speed limits on the AquaRide. These are transport speed, fast maintenance speed, maintnance/fast restore speed, and restore speed. For the maintenance and restore modes, the fast speed is selected by pressing the speed select...
  • Page 21 PIN 4 -- POT. WIPER CONTROL BOARD WHEEL DRIVE J4-3 PIN 13 -- POT. LO POT. IN Amps = 23 POT. 5K OHM SPEED CONTROLLER FORM NO. 56043089 / AquaRide ™ / BRX 700 - 19 19 19 19 19...
  • Page 22 FIGURE 4 FIGURE 4 MODE (M1, M2) POT WIPER BRAKE - POT HIGH STATUS POT LOW SPEED LIMIT HORN Used (9 pins) Not Used (9 pins) 20 20 20 20 20 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 23: Wheel Drive Troubleshooting Guide

    • • • • • Speed controller has sensed an operation error code fault. 03 fault code. (see the Status LED Fault Codes (Table 2) in the Electrical System) * = See Curtis Speed Control Troubleshooting Section. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 21 21 21 21 21...

  • Page 24: Steering Spindle & Wheel Drive Motor Assembly Removal

    Loctite 242 to all the cap screws to prevent the fasteners from backing out. 6 6 6 6 6 Re-assemble in reverse order following all the steps outlined in the steer spindle and drive motor removal section. 22 22 22 22 22 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 25 WHEEL DRIVE SYSTEM WHEEL DRIVE SYSTEM WHEEL DRIVE SYSTEM WHEEL DRIVE SYSTEM WHEEL DRIVE SYSTEM FIGURE 6 FIGURE 6 FIGURE 6 FIGURE 6 FIGURE 6 FRONT FORM NO. 56043089 / AquaRide ™ / BRX 700 - 23 23 23 23 23...

  • Page 26: Brake Adjustment

    Service by replacing worn brake band and readjust and test for proper brake operation. FIGURE 7 FIGURE 7 FIGURE 7 FIGURE 7 FIGURE 7 No Gap Pivot FRONT 24 24 24 24 24 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 27: Drive Wheel Brake Strap Replacement

    A new carbon brush measures 20mm (.780 inches) in length. Replace the brushes when worn to a length less than 9.5mm (.375 inches). FIGURE 8 FIGURE 8 FIGURE 8 FIGURE 8 FIGURE 8 FRONT FORM NO. 56043089 / AquaRide ™ / BRX 700 - 25 25 25 25 25...

  • Page 28: Potentiometer Removal & Testing

    If you do not get these readings replace the potentiometer. FIGURE 9 FIGURE 9 FIGURE 9 FIGURE 9 FIGURE 9 FRONT Violet Yellow Gray Grn/Yel 26 26 26 26 26 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 29: Potentiometer Installation & Adjustment

    Check both again and readjust. FIGURE 10 FIGURE 10 FIGURE 10 FIGURE 10 FIGURE 10 Right Side View Front View FORM NO. 56043089 / AquaRide ™ / BRX 700 - 27 27 27 27 27...

  • Page 30: Scrub Brush System

    • Cylindrical Brush System Overview See Figure 6. The machines AquaRide SE and BRX 700 use two cylindrical brushes that counter rotate to sweep up light debris and scrub at the same time. Each scrub brush is powered on opposing ends by 3/4 HP permanent magnet motors attached to separate poly-V belt/pulley drives.

  • Page 31: Scrub Brush System Troubleshooting

    Note: Reference the Main Control Board Troubleshooting Guide in the Electrical System of this manual for specific fault descriptions and service repair actions. FIGURE 1 FIGURE 1 FIGURE 1 FIGURE 1 FIGURE 1 FORM NO. 56043089 / AquaRide ™ / BRX 700 - 29 29 29 29 29...

  • Page 32: Scrub Deck Removal

    FIGURE 2 FIGURE 2 FIGURE 2 FIGURE 2 FIGURE 2 Set stop bolt so that brush housing is approximately .38" above the floor (cyl). FRONT 30 30 30 30 30 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 33: Brush Deck Actuator Removal

    Maintenance Mode Switch ( ( ( ( ( D D D D D ) ) ) ) ) (See Electrical System for steps to enter the Service Test Mode ). FIGURE 3 FIGURE 3 FIGURE 3 FIGURE 3 FIGURE 3 FRONT FORM NO. 56043089 / AquaRide ™ / BRX 700 - 31 31 31 31 31...

  • Page 34: Scrub Brush Motor(S) Removal

    CCW* FIGURE 4 FIGURE 4 FIGURE 4 FIGURE 4 FIGURE 4 CCW* Right side belt FRONT *Rotation of shaft from shaft end. 32 32 32 32 32 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 35: Scrub Brush System Maintenance

    FIGURE 6 FIGURE 6 FIGURE 6 Brush Left Motor Right Motor FRONT CCW Rotation CCW Rotation Belt Belt from shaft end from shaft end BLUE FORM NO. 56043089 / AquaRide ™ / BRX 700 - 33 33 33 33 33...

  • Page 36: Solution System

    (B) directs the solution in front of the scrub brush when in the restoration mode (maximum flow). FIGURE 1 FIGURE 1 FIGURE 1 FIGURE 1 FIGURE 1 FRONT 34 34 34 34 34 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 37: Operational Overview Of The Solution Pump & Solenoid Functions

    Speed Controller Control Board WHT/BRN VIO/BLK Valve, Maint. Solenoid WHT/BRN WHT/ORN NOTE: PRESSURE SWITCH IS Valve, Restore Solenoid PART OF PUMP ASSEMBLY WHT/BRN Pump, Accessory FORM NO. 56043089 / AquaRide ™ / BRX 700 - 35 35 35 35 35...

  • Page 38: Troubleshooting Guide

    Service Tip: The manual solution shut off arm must be placed in the full CLOSED position (located next to filter). This prevents loss of solution when servicing the filter strainer with a partial or full tank. 36 36 36 36 36 - FORM NO. 56043089 / AquaRide ™...

  • Page 39: Major Components Specifications

    Position nozzle fixture as shown (nozzle fixture flat must be 90º to bracket arm). FIGURE 3 FIGURE 3 FIGURE 3 FIGURE 3 FIGURE 3 Bracket Flats Flats FORM NO. 56043089 / AquaRide ™ / BRX 700 - 37 37 37 37 37...

  • Page 40: Solution Pump Removal

    Remove the two screws that fasten the valve body to the mount bracket to complete its removal. FIGURE 4 FIGURE 4 FIGURE 4 FIGURE 4 FIGURE 4 FRONT 38 38 38 38 38 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 41: Solenoid Valve Disassembly And Cleaning

    Thoroughly wash out all debris from the Valve Body Seat (T) (T) then reassemble and test the solenoid for proper operation. FIGURE 5 FIGURE 5 FIGURE 5 FIGURE 5 FIGURE 5 O-Ring FORM NO. 56043089 / AquaRide ™ / BRX 700 - 39 39 39 39 39...

  • Page 42: Recovery System

    FIGURE 1 FIGURE 1 FIGURE 1 FRONT Float Cage Recovery & Ball Tank Cover Vacuum Motors Cover Gasket Vacuum Hose Drain Hose Recovery Bladder Pickup Shoes 40 40 40 40 40 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 43: Vacuum Motor Circuit Overview

    Battery, 36 Vdc BRN/YEL Sw, Spst Sw, Seat Thermistor Interface Control Board J2-8 Speed Controller WHT/BRN WHT/BRN GRA/BLK Vacuum Solenoid Coil Contact N.o. Motor, Vac FORM NO. 56043089 / AquaRide ™ / BRX 700 - 41 41 41 41 41...

  • Page 44: Vacuum System Electrical Circuit Overview

    The vacuum motors will run continuously without the (normal) machine auto mode interruptions. Examples: No foot pedal throttle inputs, no 10 sec. time delay shut-off, no auto full indicator display and system shut down, no operator in seat input. 42 42 42 42 42 - FORM NO. 56043089 / AquaRide ™...

  • Page 45: Troubleshooting Guide

    Another method of accessing the cage float for servicing is to remove the (6) (B) (B) Screws and remove the vacuum duct housing (C) from the recovery tank top opening. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 43 43 43 43 43...
  • Page 46 RECOVERY SYSTEM RECOVERY SYSTEM RECOVERY SYSTEM RECOVERY SYSTEM RECOVERY SYSTEM FIGURE 3 FIGURE 3 FIGURE 3 FIGURE 3 FIGURE 3 FRONT 44 44 44 44 44 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 47: Vacuum Motor(S) Removal

    Note: There is some weight to the tank assembly. Be careful when lifting it off ask for an extra helper to assist. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 45 45 45 45 45...

  • Page 48: Recovery Tank Bladder Removal

    (U) onto the aluminum drain tube drop the bushing into a small cup of warm water to soften. 10 10 10 10 10 Fill the solution tank and check for leaks. 46 46 46 46 46 - FORM NO. 56043089 / AquaRide ™...
  • Page 49 FIGURE 6 Bladder Recovery Tank Bladder tube Recovery tank Once bladder tube is visible FRONT FRONT use bar to pry it into the tank hole opening. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 47 47 47 47 47...

  • Page 50: Vacuum Shoes Removal For Maintenance

    Rinse the shoe housings with warm water to remove any build up of string, hair or carpet fibers. Then reinstall shoes in reverse order of removal. FIGURE 7 FIGURE 7 FIGURE 7 FIGURE 7 FIGURE 7 FRONT 48 48 48 48 48 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 51: Electrical System

    - Use a combination of multiple 2-volt cell units (wired in series) to construct a 36 Volt DC battery pack system. - Nilfisk-Advance recommended battery pack capacity is a 238 or 305 AH @ 20 Hour Rate deep cycle battery system (six 6V- batteries).

  • Page 52: Description Of The Battery Low Voltage Cutout Feature

    WARNING! WARNING! WARNING! WARNING! Do not fill the batteries before charging. Only charge batteries in a well-ventilated area. Do not smoke while servicing the batteries. 50 50 50 50 50 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 53: Battery Maintenance

    1.265 Initial 1.265 Initial Charged Charged Charged Charged Charged Full Charge Full Charge Full Charge Full Charge Full Charge 100% 1.265 1.225 1.190 1.155 Discharged 1.120 FORM NO. 56043089 / AquaRide ™ / BRX 700 - 51 51 51 51 51...

  • Page 54: Actuator Drive Nut Adjustment

    Service Tip: See Figure 4. Note the correct orientation of the Spring Housing (C) (C) when installing the complete motor assembly and also run the spring housing assembly to the IN (retracted) position for machine installation. 52 52 52 52 52 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 55 FIGURE 3 FIGURE 3 FIGURE 3 1/4" (6.3mm) Spring Housing Assembly 3-7/8" (98.5mm) FIGURE 4 FIGURE 4 FIGURE 4 FIGURE 4 FIGURE 4 Pin Pocket FRONT FORM NO. 56043089 / AquaRide ™ / BRX 700 - 53 53 53 53 53...

  • Page 56: Curtis Speed Control

    PROGRAM key), scroll through the menu until “Clear Diagnostic History” is the top line in the display, and then press MORE INFO again. The programmer will prompt you to acknowledge or cancel. See the PROGRAMMER OPERATION section of this chapter for more detail on programmer operation. 54 54 54 54 54 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 57 Fwd/Rev drive pedal before turning on the main key switch or activating the throttle before sitting on the seat. This can be cleared by returning the operator’s drive pedal to neutral and cycling the key switch OFF and ON. FORM NO. 56043089 / AquaRide ™...
  • Page 58 However, it is recommended that the controller exterior be cleaned periodically, and if a handheld programmer is available, this periodic cleaning provides a good opportunity to check the controller’s diagnostic history file. 56 56 56 56 56 - FORM NO. 56043089 / AquaRide ™...
  • Page 59 When this step has been completed, the programmer displays the controller’s model number, date of manufacture and software revision code. Following this initial display, the programmer displays a prompt for further instructions. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 57 57 57 57 57...
  • Page 60 L /S P L UG C /L E MR R E V C /L 1 4 0 L /S E MR R E V C /L 58 58 58 58 58 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 61 LED on the “down” key no longer lights up. PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM FORM NO. 56043089 / AquaRide ™ / BRX 700 - 59 59 59 59 59...
  • Page 62 On = voltage is applied to main relay coil MOTOR R Cold motor resistance, in mOhms PUSH ENABLE IN On = push enable switch is closed 60 60 60 60 60 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 63 SPD LIMIT POT FAULT Speed limit pot input voltage out of range THERMAL CUTBACK Cutback, due to over-/under-temperature THROTTLE FAULT 1 Throttle input voltage out of range FORM NO. 56043089 / AquaRide ™ / BRX 700 - 61 61 61 61 61...
  • Page 64 CLEAR DIAG HISTORY Clear diagnostic history memory CONTRAST ADJUSTMENT Adjust display contrast LANGUAGE SELECTION Select displayed language PROGRAMMER INFO Display programmer information CONTROLLER INFO Display controller information 62 62 62 62 62 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 65 LED lights up. To exit the Self-Test, unplug the programmer or turn P QR ST U VWX Y Z x ½ º off the controller, and then repower it without holding the MORE INFO key. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 63 63 63 63 63...

  • Page 66: Main Control Board Functional Overview

    5. Check excessive belt tension and idler bearing. *** See the Main Control Board Special Program Options section to activate the “Scrub Deck Motor Type” Selection function. 64 64 64 64 64 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 67 • With low resistance there is an excessive amount of current. • The excessive current will either melt the wires or open a fusible link. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 65 65 65 65 65...

  • Page 68: Main Controller Service Test Mode

    SERVICE TEST MODE: To assist in the troubleshooting and servicing of the electrical system and related components on the AquaRide extractors, a special test mode which allows independent control of the various outputs and monitoring of the various inputs has been incorporated.
  • Page 69 Brief Off Green Flash – Brush motor output is on and brush motor current is not being sensed (abnormal condition). Brief Off Green Flash Brief Off Green Flash Flashing Red Flashing Red Flashing Red Flashing Red Flashing Red – Brush motor overload has occurred. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 67 67 67 67 67...
  • Page 70 Brief Off Green Flash - Vacuum motor output is on and vacuum motor current is not being sensed (abnormal condition). Flashing Red Flashing Red Flashing Red Flashing Red Flashing Red – Vacuum motor overload has occurred. 68 68 68 68 68 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 71 Wand Switch (I I I I I ): ): ): ): ): Wand Switch ( Wand Switch ( This switch does not control any output functions. Pressing this switch will illuminate the wand indicator. FORM NO. 56043089 / AquaRide ™ / BRX 700 - 69 69 69 69 69...

  • Page 72: Main Control Board Special Program Options

    FACTORY DEFAULT: MODE = 0 (FIXED PRESSURE MODE), MAINTENANCE SCRUB PRESSURE = 3, RESTORE SCRUB PRESSURE = The scrub brush pressure on the AquaRide can be adjusted to compensate for different brush and/or carpet types. The maintenance mode settings are 1 to 5 and the restore mode settings are 6 to 9. For each mode (maintenance or restore) the values represent a relative load on the motors with the small numbers (1 &...
  • Page 73 FACTORY DEFAULT: ON The AquaRide is equipped with a feature that will automatically shut off the vacuum and scrub systems and display “FULL” on the status display if the recovery tank becomes filled. If problems are encountered with the vacuum automatic shutoff feature, such as the vacuum shutting off even if the recovery tank is not full, this feature can be turned off (see also, vacuum auto-shutoff threshold adjustment).
  • Page 74 11 To exit the error code recall mode, turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the off off position. 72 72 72 72 72 - FORM NO. 56043089 / AquaRide ™ / BRX 700...
  • Page 75 FACTORY DEFAULT: ON The control system on the AquaRide is programmed to limit the maximum speed while scrubbing to a value less than that allowed for driving when not scrubbing. The speed select switch on the control panel will override this speed limit feature and allow scrubbing at a higher rate of speed.
  • Page 76 FACTORY DEFAULT: 1 (10 MINUTES) If the AquaRide is left in an idle state for a period determined by the sleep delay setting the control unit will automatically raise the scrub deck and turn off any accessories. This is to conserve battery power. The sleep period is adjustable from 10 to 90 minutes in 10 minute increments.
  • Page 77 FACTORY DEFAULT: 0 (OFF) The AquaRide is equipped with an audible warning device which functions as a horn, a back-up alarm, and a forward annunciator. The volume of the back-up alarm can be adjusted to one of ten settings. 1 is the minimum setting and 9 is the maximum setting, 0 is off.
  • Page 78 ELECTRICAL SYSTEM ELECTRICAL SYSTEM ELECTRICAL SYSTEM ELECTRICAL SYSTEM ELECTRICAL SYSTEM Drive Motor Breakdown Drive Motor Breakdown Drive Motor Breakdown Drive Motor Breakdown Drive Motor Breakdown 76 76 76 76 76 - FORM NO. 56043089 / AquaRide ™ / BRX 700...

  • Page 79: Electrical Component Location

    Motor, Drive Wheel Motor, Pump Motor, Vacuum Motor, Vacuum Motor, Brush Motor, Brush (SE & BRX 700 only) Potentiometer, 5K Key Switch ™ FORM NO. 56043089 AquaRide / BRX 700 - 77 - 77 - 77 - 77 - 77...

  • Page 80: Wiring Schematic

    MOTOR, BRUSH Amps = 22 OPTIONAL RED/BRN 14 AWG GRN/RED CIRCUIT BREAKER, 10 AMP SW, SIDE BROOM MOTOR, SIDE BROOM Amps = 8.8 OPTIONAL 78 78 78 78 78 - - - - - FORM NO. 56043089 AquaRide ™ / BRX 700...

  • Page 81: Wiring Diagram

    Pressure Switch Is Part Of Pump Assembly Note: On The Extractor L1 Is For Maintenance MOTOR, BRUSH MOTOR, BRUSH And L2 Is For Restoration Cleaning. ™ FORM NO. 56043089 AquaRide / BRX 700 - 79 - 79 - 79 - 79 - 79...
  • Page 82 ☎ +1 800 989 2235 – Fax 1 800 989 6566 Distriktsrepresentanter over hele landet Dublin 18 ☎ +353 1 2943838 – Fax +353 1 2943845 SVERIGE SVERIGE SVERIGE SVERIGE SVERIGE Nilfisk-Advance of America, Inc. Nilfisk-Advance AB JAPAN JAPAN JAPAN JAPAN JAPAN 300 Technology Drive Sjöbjörnsvägen 5, 117 67 Stockholm Nilfisk-Advance Inc.

This manual is also suitable for:

Aquaride se brx 700Aquaride se

Table of Contents