Advertisement
English
FEATURES
• 450W
• 2 speed operation
• 0.7 litre jug
• Removable pulp container
• Stainless steel sieve
• Removable tray
• Cord storage
Fig A - Before first use:
Before using your Juicer for the first time,
make sure it is disconnected from the
electrical supply, then remove all packaging
from the sieve & pulp container.
To remove the packaging, open the right-
hand latch (7), then the left-hand latch (8).
Lift the cover (5) & tray (6) from the appliance.
Remove the packing from the sieve (12) and
from the pulp container (3).
Pull the sieve housing & sieve from the Juicer.
All parts must be cleaned as recommended in
the section "How to take care of your Juicer".
The motor housing must only be cleaned with
a damp cloth, and dried thoroughly before
use.
Inspect the sieve for signs of damage.
Note: Do not use the appliance if the rotating
sieve is damaged.
Fig B - How to assemble your Juice
Extractor
Place the sieve housing (13) on the motor
housing (1), then place the sieve (12) into the
sieve housing, pressing it onto the sieve
adaptor (14).
Place the cover (5) on top of the seive
housing. Fit the hooks of the latches over the
recesses in the cover, then push the right-
hand latch (7) and the left-hand latch (8)
down ensuring they lock in place.
Fit the tray (6) onto the cover (5). This can be
fitted as a cover for storage, or inverted to act
as a tray where ingredients can be
temporarily stored before juicing.
Place a suitable container under the spout (9).
How to use your Juicer
This appliance is designed to extract juice from
fruits & vegetables.
Do not use this appliance for any other purpose.
For indoor domestic use only.
Prepare material to be processed by washing
thoroughly and peeling as required. Remove
all pips and large seeds. Cut large fruits or
vegetables into small pieces which will fit the
inlet chute.
Smaller items of food can be placed on the
tray ready to be directed into the chute with
the pusher (11).
Make sure the speed selector (2) is in the ''0''
(OFF) position, then plug the cord-set into a
power outlet.
Note: Make sure that the voltage shown on
the
underside
corresponds with the local supply voltage.
Rotate the speed selector to position 1 or 11
as required. Low speed should be used for
soft fruits and high speed for harder fruits.
Check the jug and pulp collector are in place,
and feed the ingredients into the inlet chute.
The pusher (11) can be used to gently guide
the ingredients down the inlet slot. Do not
overload the machine. Too much pressure
may cause material to jam the inlet chute.
This appliance should not be operated
continuously for more than 2 minutes at a
time. After 2 minutes use, the appliance
should be allowed to cool at least one minute
before using it again.
If a blockage occurs, NEVER USE
FINGERS OR ANY OBJECT OTHER THAN
THE PUSHER TO CLEAR THE INLET
CHUTE.
If the food cannot be dislodged, turn the
speed selector to the "0" position (OFF) and
UNPLUG the POWER CORD FROM
OUTLET.
Remove the cover as described in "Before
first use" and clear the blockage. Replace the
cover, re-connect the Juicer to the electrical
supply & resume juicing.
When juicing is completed, the switch should
be returned to the off (0) position, and allow
the motor to come to a stop. The jug should
be left in place until the juice stops flowing
from the spout.
UNPLUG POWER CORD FROM THE
OUTLET, and disassemble the juice extractor.
Empty the pulp from the collector and clean
all parts as soon as possible after you have
finished processing.
-4-
of
the
motor
housing
Advertisement
