Related Manuals for Mutec Mc-8
Summary of Contents for Mutec Mc-8
- Page 1 AES3-AES3id Digital Multichannel Audio Format and 8-channel Sampling Rate Converter...
-
Page 3: Safety Instructions
§1 Warranty MUTEC GmbH warrants the flawless performance of this product to the original buyer for a period of two (2) years from the date of purchase. If any failure occurs within the specified warranty period that is caused by defects in material and/or workmanship, MUTEC GmbH shall either repair or replace the product free of charge within 90 days. -
Page 5: Table Of Contents
(both panels are equal) MC-8 Rear Panel ......10 MC-8.1 Rear Panel ..... . . 10 INSTALLATION Content of the Box . -
Page 7: Main Differences Between Mc-8 And Mc-8.1
HOLD function secures interruption-free audio conversion even in cases of an unstable or absent clock reference! This all makes MC-8 and MC-8.1 for sure the most flexible and useful AES3 to AES3id digital audio converters allowing to handle any conversion appli- cation with ease. -
Page 8: Peripheral Mutec Products
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Peripheral MUTEC Products... -
Page 9: Control Elements And Terminals
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > CONTROL ELEMENTS AND TERMINALS MC-8 + MC-8.1 Front Panel (both panels are equal) -
Page 10: Mc-8 Rear Panel
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > MC-8 Rear Panel 1 AES3id OUT 1–... -
Page 11: Installation
Always be sure to connect the Word Clock output of the MC-8 the same, as this is the only way to or MC-8.1 to the corresponding input of the device you wish to synchro-... -
Page 12: Wiring The Aes/Ebu And Aes/Ebuid Interfaces
\\\\\\\\\\\\ I N S TALLAT I O N I N S TALLAT I O N I N S TALLAT I O N > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Wiring the AES/EBU and AES/EBUid Interfaces AES/EBU Since some manufacturers offer optimized... -
Page 13: General Operation
2 Switching the »SELECT« key activtes individual functions within one powering-up! function menu. We also recommend reading the chapter CONTROL ELEMENTS AND TERMINALS for information on how to connect your MC-8 or MC-8.1! 2. SELECT 1. MENU selects individual selects individual functions within function menus. -
Page 15: Operating The
So, you can split up all of the necessary adjustments in two simple steps, which leads to the following two questions for the basic operation of your MC-8 or MC-8.1: 1) How I want to convert? With or without SRC function? →... -
Page 16: Conversion From One Input To All Four Outputs
That means: Input 1 → Outputs 1+ 2+3 + 4 Using this function, your MC-8 or MC-8.1 works as a typical 1 → 4 digital au- dio signal distribution amplifier. The input signal can be between 32.0kHz and 192.0kHz. Because the SRC function is not selected, your MC-8 or MC-8.1 is only electrically converting the signals and no adjustments in the... -
Page 17: Conversion From One Input To All Four Outputs Including The Sampling Rate Conversion Function
Conversion 44.1 HOLD 44.1 IN2 → OUT3/4 AES11 176.4 176.4 IN1- 4 → OUT1- 4 Your MC-8 or MC-8.1 allows to syn- 48.0 48.0 192.0 192.0 chronize the internal SRCs to various clock 88.2 88.2 reference signals. These possible references... -
Page 18: Conversion From Four Inputs To Four Outputs Including The Sampling Rate Conversion Function
88.2kHz. ples below). 32.0 32.0 STATUS Menu 96.0 96.0 44.1 44.1 This area displays different clock-related conditions of your MC-8 or MC-8.1. 176.4 176.4 There is no access for changing settings. 48.0 48.0 192.0 192.0 88.2 88.2 »LOCK«... -
Page 19: Appendix
B E D I E N E L E M E N T E B E D I E N E L E M E N T E B E D I E N E L E M E N T E >... -
Page 20: Switching-Off The Termination Of The Word Clock Input
Remount the aluminium cover thoroughly before you attempt to operate the unit! When MC-8 or MC-8.1 is shipped, the BNC-based Word Clock input connec- tor is terminated internally with 75 Ω. Therefore, one jumper is put on two pins - Position 2 - of the 3-pin socket JP1. -
Page 21: Technical Data
Weight MC-8: ~ 751g, MC-8.1: ~ 748g > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >... - Page 22 > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > WWW.MUTEC-NET.DE FON 0049-(0)30-746880-0 ALL SOFTWARE AND HARDWARE PRODUCT NAMES ARE REGISTERED TRADEMARKS OF THEIR RESPECTIVE OWNERS. FAX 0049-(0)30-746880-99 WE RESERVE THE RIGHT TO CHANGE TECHNICAL DETAILS WITHOUT PRIOR NOTICE. © MUTEC GmbH 2002 • 7045-014...