AGA marvel ML24BN Installation, Operation And Maintenance Instructions
Beer dispensers
Hide thumbs
Also See for ML24BN:
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AGA marvel ML24BN
Summary of Contents for AGA marvel ML24BN
-
Page 1: Beer Dispensers
EN Installation, Operation and maintenance Instructions FR Instructions d’installation, d’utilisation et d’entretien ES Instrucciones de instalación, operación y mantenimiento Beer Dispensers Distributeurs de bière Dispensadores de cerveza ML24BN ML24BS ML24BT... -
Page 2: Table Of Contents
Leveling the appliance ............4 Electrical connection ............5 Recognize Safety Symbols, Installing the anti-tip device ..........6 Product dimensions ML24BN ...........8 Words, and Labels. Product dimensions ML24BS and ML24BT ....9 Product dimensions ML24BSSM and ML24BTSM ..10 Using your Electronic control ..........11 Starting your appliance ..........11... -
Page 3: Unpacking Your Appliance
UNPACKING YOUR APPLIANCE Warranty Registration WARNING It is important you send in your warranty registration card immediately after taking delivery of your appliance or you can register online at www.agamarvel.com. EXCESSIVE WEIGHT HAZARD Use two or more people to move product. Failure to do so can result in personal injury. -
Page 4: Installing Your Appliance
35" (88.9 cm) it is important this area not be obstructed and the grille ML24BTP openings kept clean. AGA MARVEL does not recommend the use of a custom made grille as air flow may be restrict- Table A ed. (See Figure 2). -
Page 5: Electrical Connection
INSTALLING YOUR APPLIANCE WARNING Electrical Shock Hazard • Do not use an extension cord with this appliance. They can be hazardous and can degrade product performance. • This appliance should not, under any circumstanc- es, be installed to an un-grounded electrical supply. •... -
Page 6: Installing The Anti-Tip Device
INSTALLING THE ANTI TIP DEVICE Anti-Tip WARNING Bracket Leveling Leg • ALL APPLIANCES CAN TIP RESULTING IN INJURY. • INSTALL THE ANTI-TIP Bottom View of ⁄ " BRACKET PACKED WITH Beer dispenser (54.6 cm) THE APPLIANCE. • FOLLOW THE INSTRUC- TIONS BELOW Front of cabinet Anti-Tip Device... - Page 7 INSTALLING THE ANTI TIP DEVICE WARNING TIP OVER HAZARD: One of the rear cabinet leveling legs must be engaged under an anti-tip bracket. NOTE When the floor mounted anti-tip bracket is used the mini- mum adjusted height of the cabinet is increased by ⁄...
-
Page 8: Product Dimensions Ml24Bn
PRODUCT DIMENSIONS ML24BN ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J" 24" **34" to 35" ⁄ " ⁄ " to 34 ⁄ " ⁄ " ⁄ " ⁄ " ⁄ " ML24BN(S) (61 cm) (86.4 to 88.9 cm) -
Page 9: Product Dimensions Ml24Bs And Ml24Bt
PRODUCT DIMENSIONS ML24BS AND ML24BT ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J" ML24BS(S) 24" **34" to 35" ⁄ " ⁄ " to 34 ⁄ " ⁄ " ⁄ " ⁄ " ⁄ "... -
Page 10: Product Dimensions Ml24Bssm And Ml24Btsm
PRODUCT DIMENSIONS ML24BSSM AND ML24BTSM ⁄ " Single dispense tower shown (54.6 cm) ⁄ " (65.2 cm) ⁄ " ⁄ " (30.3 cm) (117.9 cm) 11" ⁄ " (27.9 cm) (31.1 cm) ⁄ " (93.5 cm) ⁄ " (15.9 cm) ⁄... -
Page 11: Using Your Electronic Control
USING YOUR ELECTRONIC CONTROL Temp Temp Minus On/Off Plus Lock System Status Display Area keypad indicators keypad keypad keypad Figure 12 Electronic single zone control To wake the display press any keypad. A confirm tone will sound, and the current storage compartment temperature will be displayed. -
Page 12: Adjusting The Temperature
USING YOUR ELECTRONIC CONTROL Adjusting the temperature: Temperature mode: To set or check the set-point temperature (with the control The temperature mode is preset from the factory in Fahren- out of sleep mode), press the "-" or "+" keypads. "SET" will heit (°F) but you have the option to change it to Centigrade be indicated on the user interface panel and the current (°C). -
Page 13: Power Failure
USING YOUR ELECTRONIC CONTROL Vacation mode: This operating mode can be used to save energy during Power Failure high cost energy periods, or when you won't be using your ALARM RESET appliance for an extended period of time by disabling the lights, alarm tones, and keypad entry tones. -
Page 14: Overlay Door Panel Installation
OVERLAY DOOR PANEL INSTALLATION If you purchased an overlay panel model, your unit is WARNING equipped with articulated hinges to allow fully integrated built-in installations. Custom panel thicknesses of ⁄ " (15 mm) and ⁄ " (18 mm) are accommodated. Use extreme caution with the articulated hinges. - Page 15 OVERLAY DOOR PANEL INSTALLATION Press and hold down this tab on the wire connector and pull the connector apart. Overlay panel flush with top of door. Figure 14 Step 2: Remove the door gasket With the door laying on a flat surface and starting at a Overlay panel to corner of the door remove the magnetic door gasket from Holes in...
- Page 16 OVERLAY DOOR PANEL INSTALLATION Clearance for hinge Clearance at top and bottom Clearance for for hinge screw head, at top and Clearance for 4 places bottom screw head, 4 places Figure 16 Left Hand Hinged Door 24" (61 cm) wide appliance Figure 18 Right Hand Hinged Door 24"...
- Page 17 OVERLAY DOOR PANEL INSTALLATION CAUTION Weight of overlay door panel must not exceed 15 pounds (6.8 kg) for a solid door model. #10 x 1/2" screw Step 4: Assemble the panel to the door The preferred method of attaching the panel to the door is to clamp the panel to the door so it cannot move while drilling the screw pilot holes.
- Page 18 OVERLAY DOOR PANEL INSTALLATION Step 6: Secure the cabinet Use the #8 x ⁄ " black screws from the literature pack to secure the counter top to the cabinet top through the holes in the cabinet "Z" bracket. Cabinet "Z" bracket #8 x ⁄...
-
Page 19: Using Your Beer Dispenser
USING YOUR BEER DISPENSER Shelving If you are using a quarter barrel of beer, you can add shelf The unit is shipped with the (2) shelves taped in place in space for keeping your mugs chilled. The quarter barrel the upper and the lower shelf positions. Remove them from must set on the floor, it cannot fit on the shelf, see the refrigerator and arrange them as follows when setting Figure 24. -
Page 20: Tap Equipment And Assembly
USING YOUR BEER DISPENSER Tools required for installation: This beer dispensing unit will support one half ( ⁄ ) barrel or one quarter ( ⁄ ) barrel. The double draft tower units can Flat bladed screwdriver support two sixth ( ⁄... - Page 21 USING YOUR BEER DISPENSER Single Dispense Tower Kit Double Dispense Tower Kit Connect ,etc..Connect ,etc..Figure 32 Figure 31 Figure 27 Double Single Dispense Hose clamps Dispense Tower use for connections Tower Hose clamps use for connections Figure 26 Coupler Figure 33 Figure 28...
- Page 22 USING YOUR BEER DISPENSER 4. If you are installing your keg refrigerator under a coun- Rear of counter top ter you will need to drill 5 holes in the counter top to ⁄ " mount the tower. The first hole is a 1 ⁄...
- Page 23 USING YOUR BEER DISPENSER 8. Locate the CO tank in the corner of the refrigerator as shown in Figure 40 and secure with the chain. Close the faucet handle on the tower. 9. Hooking up the keg coupler to the keg: Verify the cou- pler is in the "OFF"...
-
Page 24: Tank
USING YOUR BEER DISPENSER Optional CO tank external mounting bracket: The optional mounting bracket is designed to hold the 5# Remove foam plug cylinder that comes with the beer dispenser. Larger from hole port cylinders may be purchased from a third party and mounted externally. -
Page 25: Co Regulator
USING YOUR BEER DISPENSER Regulator (Double Dispense Tower) Regulator (Single Dispense Tower) Your beer dispenser comes equipped with a 5 pound CO Your beer dispenser comes equipped with a 5 pound CO tank and a dual gauge regulator. The lower gauge should tank and a single gauge regulator. -
Page 26: Drain Kit
USING YOUR BEER DISPENSER AND CARE AND CLEANING Drain kit (All Models): Push faucet handle back toward The drain kit is shipped in Removable tower to close the faucet place and ready to use. To empty: Pull drain hose out of grate for clean- bottle cap, remove bottle from unit, unscrew cap and dis- ing sump area... -
Page 27: Tap Cleaning Kit
CARE AND CLEANING Cleaning and Maintaining Dispensing System The dispensing system needs to be cleaned between usage to prevent spoilage and/or foul taste in your beer. Tap Cleaning Kit This is an optional item (part number 42242373) Kit in- cludes everything to quickly clean tap. Includes cleaning solution, pump, mixing bottle, brush and wrench. -
Page 28: Front Grille
CARE AND CLEANING AND ENERGY SAVING TIPS The following suggestions will minimize the Front Grille cost of operating your refrigeration appliance. Be sure that nothing obstructs the required air flow open- ings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille area (see 1. -
Page 29: Door Alignment
If the product is within the first year warranty period The door should be parallel to the sides and top of the ap- please contact your dealer or call AGA MARVEL Cus- pliance. If alignment is necessary the door may be adjusted tomer Service at 800.223.3900 for directions on how to... -
Page 30: Troubleshooting
TROUBLESHOOTING Before You Call for Service If the appliance appears to be malfunctioning, read through this manual first. If the problem persists, check the trouble- shooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. -
Page 31: Household Product Warranty
Limited One Year Parts and Labor Warranty Not Supplied or Designated by AGA MARVEL AGA MARVEL warrants that it will supply all necessary The above warranties also do not apply if: parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective •... - Page 32 www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.3900 41013400-EN Rev E All specifications and product designs subject to change without notice. Such revisions do not entitle 10/29/14 the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
Need help?
Do you have a question about the ML24BN and is the answer not in the manual?
Questions and answers