Deflating With The Low Pressure Hose; Inflating With The High Pressure Hose And Accessories; Accessories; Inflating With The High Pressure Hose - Ryobi CIT1800G Owner's Operating Manual Original Instructions

„ Turn the hose clockwise as far as it will turn.
„ Press the low pressure (I) switch to start inflating.
„ When the desired pressure is reached, turn the switch
off.
„ Remove the hose by turning it counterclockwise as far
as it will turn and removing it from the inflator.
„ Store the hose in hose wrap on the left side of the
product.
Always leave low pressure hose free of obstructions
and with pinch valve adaptor off when not in use.
Overheating could occur low pressure hose is blocked.

DEFLATING WITH THE LOW PRESSURE HOSE

See figure 5
The low pressure hose, when placed in the deflator, can
be used to remove air from inflated items.
„ Place the hose inside the deflator.
„ Press the low pressure (I) switch to start deflating.
„ When the item has been deflated, turn the switch off.
„ Remove the hose by pulling it from the deflator.
„ Store the hose in hose wrap on the left side of the
product.

INFLATING WITH THE HIGH PRESSURE HOSE

See figure 6
The air chuck on the high pressure hose can be used
without adaptors to inflate tires or with any application that
has a valve stem that fits the air chuck opening.
NOTE: When inflating items of 10 PSI, .69 BAR, 69 kPa
or less, inflate in short bursts and check after each burst
by feel or with a calibrated measuring device to determine
accurate pressure.
„ Press mode button to activate.
„ Set desired pressure.
„ Place air chuck on valve stem and lock in place.
„ Press the high pressure (II) switch to start inflating.
„ When the desired pressure is reached, turn the switch
off.
„ Remove the hose and store in hose wrap on the right
side of the product.
„ Press and hold the mode button to deactivate the
display.
NOTE: Stand 10 feet away from item being inflated.
CAUTION
English
INFLATING WITH THE HIGH PRESSURE HOSE AND

ACCESSORIES

See figures 7 - 9
The high pressure hose can be used with the provided
adaptors to inflate a variety of items.
„ To install accessory: insert adaptor (or needle) into air
chuck and push air chuck clamp down until it locks into
place. Inflate to desired pressure.
„ Remove accessory by lifting air chuck clamp up and
pulling the adaptor (or needle) from air chuck.
INFLATING MANUALLY
PRESSURE APPLICATIONS
„ Connect either high or low pressure hose to item to
be inflated.
„ Depress power switch to proper switch (low or high
pressure) until desired pressure is reached.
NOTE: Stand 10 feet away from item being inflated.
„ Turn off power switch.
ACCESSORIES
See figures 8 - 9
The supplied accessories perform a variety of functions.
The tapered adaptor can be used on smaller pinch valves
to inflate items like floats and children's toys, which usually
require the user to inflate them by blowing air into them.
The sport ball needle can be used to inflate any type of
sports ball or any other item that requires an inflation sport
ball needle.
NOTE: When inflating items of 10 PSI, .69 BAR, 69 kPa
or less, inflate in short bursts and check after each burst
by feel or with a calibrated measuring device to determine
accurate pressure.
To use the sport ball needle:
„ Insert sport ball needle into sports ball valve and
inflate.
„ Remove sport ball needle after inflation.
NOTE: Pressure required for most sports balls is too low
for accurate reading on gauge.
The presta valve adaptor can be used for presta valve
stems as described below. Before inflating a tire with a
presta valve, loosen the locking nut on the valve stem to
inflate. Once inflation is complete, tighten the locking nut
to seal the tire valve.
To use the presta valve adaptor:
„ Loosen presta valve locking nut.
„ Thread presta valve adaptor onto valve stem with
larger open end toward wheel.
„ Position the air chuck clamp in the unlock position.
10
FOR HIGH AND LOW