Ryobi CRT150K Owner's Operating Manual

Ryobi CRT150K Owner's Operating Manual

100 watt rotary hobby tool

Advertisement

OWNER'S OPERATING MANUAL
100 WATT ROTARY HOBBY TOOL
SPECIFICATIONS:
Power Input............................100 watts
No Load Speed......................7500-26,500 rpm
Collet Chuck ..........................3.0mm
Weight ....................................0.5kg (tool only)
This HOBBY TOOL is designed for light consumer use. It is NOT designed for trade or
industrial use and is not covered by warranty for use in these applications.
THANK YOU FOR BUYING A RYOBI ROTARY HOBBY TOOL
Your new rotary hobby tool has been engineered and manufactured to Ryobi's high standard
for dependability, ease of operation, and operator safety. Properly cared for, it will give
you years of rugged, trouble free performance.
CAUTION: Carefully read through this entire owner's manual before using
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions.
If you use your rotary hobby tool properly and only for what it is intended, you will enjoy years
of safe, reliable service.
Thank You again for buying Ryobi tools.
MODEL CRT150K
IMPORTANT NOTICE:
your rotary hobby tool.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
DOUBLE
INSULATED

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CRT150K and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ryobi CRT150K

  • Page 1 THANK YOU FOR BUYING A RYOBI ROTARY HOBBY TOOL Your new rotary hobby tool has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble free performance.
  • Page 2: Rules For Safe Operation

    For service we suggest you return the tool they are not safety glasses. to your nearest Ryobi Authorised Service Centre for 11. PROTECT YOUR LUNGS. Wear a dust mask if repair. When servicing, use only identical Ryobi operation is dusty.
  • Page 3 17. NEVER EXPLOSIVE breakage of parts, mounting and any other con- ATMOSPHERE. Normal sparking of the motor ditions that may affect its operation. A guard or could ignite fumes. any other part that is damaged should be prop- erly repaired or replaced by an authorised ser- 18.
  • Page 4: Installing Accessories

    ■ COLLET CHANGES INSTALLING ACCESSORIES To install a new collet, remove the collet nut and remove the old collet. Insert the collet in the hole. Replace the collet nut on the shaft. Always use WARNING: the collet which matches the shank size of the Your Hobby Tool should never be connected to the accessory you plan to use.
  • Page 5 A "handgrip" method of holding the tool is used for OPERATION (Cont.) operations such as grinding a flat surface or using cut-off discs. (Fig 6) This taper permits the Hobby Tool to be grasped Handgrip much like a pen or pencil. method of When you turn on the tool, hold it away from your holding the...
  • Page 6 2. Insert driver cable into collet (Fig.9) and secure OPERATING SPEEDS by tightening collet (fig.10). Slide driver cap over & ACCESSORIES (Cont.) collet and screw on to motor housing. The speed of the Hobby Tool is controlled by 4. Insert the collet which is suitable for the shank adjusting the variable speed dial (Fig 7).
  • Page 7: Accessory Kit

    ACCESSORY KIT APPLICABLE DRAWING QUANTITY DESCRIPTION SPECIFICATION FUNCTION REVOLUTION Cut-Off Wheel ø15/16" x 1/32",#120 4 - 6 Slice & cut off metal, ø15/16" x 3/64",#120 screw head, wire Aluminium oxide ø3/8" x 1/2", #60 2 - 5 Clean small bits, grinding clean rust, grind edge, sharp axe,...
  • Page 8 RYOBI NEW ZEALAND PTY. LTD. AUCKLAND: 503 Mt Wellington Highway, Mt Wellington, N.Z. Tel: (09) 573 0230 - Free Call: 0800 279 624 - Fax: (09) 573 0231 - Email: info@ryobi.co.nz Contact during normal business hours. THIS WARRANTY FORM SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES.

Table of Contents