Scrolling Help Text In Display Line 3 - PR 4131 User Manual

SCRoLLING HELp TExT IN DISpLAy LINE 3

[01] Set correct password
[02] Enter advanced setup menu?
[03] Select temperature input
Select potentiometer input
Select linear resistance input
Select current input
Select voltage input
[04] Select 0.0-1 V input range
Select 0.2-1 V input range
Select 0-5 V input range
Select 1-5 V input range
Select 0-10 V input range
Select 2-10 V input range
[05] Select 0-20 mA input range
Select 4-20 mA input range
[06] Select 2-wire sensor connection
Select 3-wire sensor connection
Select 4-wire sensor connection
[07] Set resistance value low
[08] Set resistance value high
[09] Select Celsius as temperature unit
Select Fahrenheit as temperature unit
[10] Select TC sensor type
Select Ni sensor type
Select Pt sensor type
Select Cu sensor type
[11] Select display unit
[12]
Select decimal point position
[13]
Set display range low
[14] Set display range high
[15]
Set relays in % of input range
Set relays in display units
[16]
Select Pt10 as sensor type
Select Pt20 as sensor type
Select Pt50 as sensor type
Select Pt100 as sensor type
Select Pt200 as sensor type
Select Pt250 as sensor type
Select Pt300 as sensor type
Select Pt400 as sensor type
Select Pt500 as sensor type
Select Pt1000 as sensor type
[17] Select Ni50 as sensor type
Select Ni100 as sensor type
Select Ni120 as sensor type
Select Ni1000 as sensor type
[69]
Select Cu10 as sensor type
Select Cu20 as sensor type
Select Cu50 as sensor type
Select Cu100 as sensor type
[18]
Select TC-B as sensor type
Select TC-E as sensor type
Select TC-J as sensor type
Select TC-K as sensor type
Select TC-L as sensor type
Select TC-N as sensor type
Select TC-R as sensor type
Select TC-S as sensor type
Select TC-T as sensor type
Select TC-U as sensor type
Select TC-W3 as sensor type
Select TC-W5 as sensor type
Select TC-Lr as sensor type
[19]
Select OFF function - relay is permanently off
Select POWER function - relay indicates power status OK
30
Select ERROR function - relay indicates sensor
error only
Select WINDOW function - relay controlled by 2
setpoints
Select SETPOINT function - relay controlled by
1 setpoint
[20] Select Normally Closed contact
Select Normally Open contact
[21] Set relay setpoint
[22] Activate relay on decreasing signal
Activate relay on increasing signal
[23] Set relay hysteresis
[24] No error action - undefined status at error
Open relay contact at error
Close relay contact at error
Hold relay status at error
[25] Set relay ON delay in seconds
[26] Set relay OFF delay in seconds
[27] Relay contact is Closed Inside Window
Relay contact is Open Inside Window
[28] Set relay window setpoint high
[29] Set relay window setpoint low
[30] Set relay window hysteresis
[31] No error action - undefined status at error
Open relay contact at error
Close relay contact at error
Hold relay status at error
[32] Set relay ON delay in seconds
[33] Set relay OFF delay in seconds
[34] Open relay contact at error
Close relay contact at error
[43] Enter password setup
Enter simulation mode
Perform process calibration
Enter display setup
Perform memory operations
Enter relay latch setup
[44]
Load saved configuration into 4131
Save 4131 configuration in 4501
[45] Adjust LCD contrast
[46]
Adjust LCD backlight
[47]
Write a 6-character device TAG
[49] Calibrate input low to process value?
[50]
Calibrate input high to process value?
[51] Enable simulation mode?
[52]
Set the input simulation value
[53]
Relay simulation - use 1 and 2 to toggle relay 1 & 2
[54] Enable password protection?
[55]
Set new password
[56]
Enable Fastset functionality?
[57] Relay setpoint - press 3 to save
[58]
Relay setpoint - Read only
[59] Select language
[60]
Use process calibration values?
[61]
Set value for low calibration point
[62] Set value for high calibration point
[63]
Select CJC connector (accessory)
Select internal temperature sensor
[64] Enable relay latch function?
[65] Relay is latched - press 3 to acknowledge
Relay(s) are latched - press 1 or 2 for release
relay 1 or relay 2
[66] Release relay? (if conditions allow)
[67]
Enter setup menu? (latched relays may release!)
4131V104-UK