Related Manuals for AcraDyne HT series
Summary of Contents for AcraDyne HT series
- Page 1 AcraDyne High-Torque Nutrunners Operations Manual PO Box 16460, Portland OR 97292-0460 • 800-852-1368 • Fax 800-582-9015 www.aimco-global.com...
-
Page 2: Table Of Contents
Table of Contents Introduction ................................................3 Safety Information ............................................3 Specifications ..............................................4 Operation .................................................5-6 Reaction Bars Safety ..........................................7-8 Accessories .................................................9 Recommended Maintenance ......................................10 AIMCO Limited Warranty ........................................11... -
Page 3: Introduction
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. This product is designed to be used in combination with the AcraDyne iEC DC tool controller for intermittent hand-held or fixtured assembly processes. -
Page 4: Specifications
AcraDyne Product Representative. • Motor Speed Setting Guidelines - AcraDyne ToolWare software, when used with an AcraDyne DC controller, offers a wide range of programming options. An experienced, trained person should be responsible for the setup of these options. -
Page 5: Operation
TECHNIQUE CAN RESULT IN SERIOUS PERSONAL INJURY, LOSS OF LIMB OR DEATH. ® AcraDyne HT Series Nutrunners are a part of a complete system including Controller, Tool Cable and Tool. ® Specific instructions on setup, programming and features are described in greater detail within the AcraDyne Controller Manuals and ToolWare software manuals that are provided with those components. - Page 6 An optional feature on AcraDyne HT Series Nutrunners is a locking clutch that allows the gearcase 270 degrees of rotation in relation to the motor/handle assembly. This feature is useful in positioning the reaction bar against the workpiece prior to the tightening event.
-
Page 7: Reaction Bars Safety
® AcraDyne HT Series Nutrunner is capable of delivering. In addition, the use of Socket Extensions of any length are strongly discouraged as they also will experience failure to an extent where tool damage or operator injury may occur. - Page 8 Reaction Bars Safety Pinch Point CAUTION IS REQUIRED. FAILURE TO EXERCISE CAUTION AND CORRECT OPERATING TECHNIQUE CAN RESULT IN SERIOUS PERSONAL INJURY, LOSS OF LIMB OR DEATH. The nature of a Reaction Bar in any continuous drive tool is to press against an object to counteract Torque Reaction as the tool is delivering Torque.
-
Page 9: Accessories
Accessories PAGE HEADER HERE CABLES Newly designed cable and connectors for excellent MODEL LENGTH ergonomics, maximum-quality signal transfer and full 24330 3 meter CE compliance. 25350 5 meter 24320 10 meter BREAKAWAY CABLE CONNECTOR Ensures disconnect of cable should stress in excess of 40 lbs occur. 25491 REACTION BARS MODEL... -
Page 10: Recommended Maintenance
Recommended Maintenance PAGE HEADER HERE Any service or preventative maintenance must be done by a trained technician or AcraDyne Authorized Service Center. • The tool gear train should be cleaned, inspected and re-greased every 25,000 tightening cycles. • Parts should be inspected for wear and any worn parts should be replaced. -
Page 11: Aimco Limited Warranty
NEW TOOL AND ACCESSORY WARRANTY Any new tool or accessory branded with the AIMCO, Uryu, AcraDyne or Eagle Industries name, and purchased from AIMCO, or through one of its authorized distributors or agents, is warranted to the original buyer against defects in materials and workmanship for a period of one (1) year* from date of delivery. - Page 12 CORPORATE HEADQUARTERS 10000 S.E. Pine St. Ave. Cristóbal Colon 14529 Portland, OR 97216 Chihuahua, Chihuahua. 31125 Mexico (800) 852-1368 52-614-380-1010 FAX (800) 582-9015 FAX 52-614-380-1019 LIT-MAN165, Rev.02/14 Printed in USA ©2014 AIMCO...