Sagem telsat gprs User Manual
  1. Manuals
  2. Brands
  3. Sagem Manuals
  4. Gateway
  5. telsat gprs
  6. User manual

Sagem telsat gprs User Manual

Gsm/gprs-gateway
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
GSM/GPRS-Gateway
TELSAT
TELSAT
TELSAT
TELSAT
GPRS
GPRS
GPRS
GPRS

Advertisement

Table of Contents
loading

Related Manuals for Sagem telsat gprs

Summary of Contents for Sagem telsat gprs

  • Page 1 User Manual GSM/GPRS-Gateway TELSAT TELSAT TELSAT TELSAT GPRS GPRS GPRS GPRS...
  • Page 2 © by Dr. Neuhaus Telekommunikation GmbH, 2004 All trade marks and product names are trade marks, registered trade marks or product names of the respective title holders. The contents of this manual and technical specifications can be changed without notice. The description of specifications in this manual does not constitute a contract.
  • Page 3 Before opening the device, always make sure that the cables have been disconnected and the power supply has been directly disconnected at the TELSAT GPRS, since otherwise dangerous voltages may be present in the device. After the installation remount the cover and fasten it with the supplied screw.

  • Page 4: Table Of Contents

    FAX-Configuration ..................31 8.4.1 Fax Report on success ............. 31 8.4.2 Select Port for Fax Calls ............31 8.4.3 Disable Modem/Phone on Fax/Modem/Phone port....32 Data Call Configuration ................32 8.5.1 Select Port for Data Calls ............32 TELSAT GPRS...
  • Page 5 Flash signal detection (used to manage two calls simultaneously)38 8.7.4 Enable / Disable SMS Configuration ......... 38 9 Installing the TELSAT GPRS modem driver on a Windows-PC......40 10 Operation: Internet via GPRS with a PC ............53 10.1 Installing the Windows dial-up network connection........53 10.2...
  • Page 6 16.38 Sample File .....................107 17 Configuration of Tones ..................114 17.1 How to program a new timing ..............116 17.2 Example-File: ..................117 18 Logfile....................... 119 19 Update the firmware..................120 20 Connection sockets ..................121 21 Technical data ....................122 TELSAT GPRS...

  • Page 7: Introduction

    The TELSAT GPRS is a GSM/GPRS-Gateway or GSM/GPRS Purpose of the Network Termination, a kind of wireless telephone socket. The device following devices can be connected to the TELSAT GPRS: • one or more analogue telephone devices to make telephone calls •...

  • Page 8: The Leds On The Device

    Search Net or Low Signal Quality Medium or High Signal Quality No Signal RAPID Flash FAX Warning, please check the fax machine connected to the TELSAT GPRS SLOW Flash SMS Received Offhook on Phone, Fax/Modem/Phone or PC port RAPID Flash...

  • Page 9: Putting The Device Into Operation

    Enter the PIN number so that the device can communicate via the GSM network. Option: If you have connected a Personal Computer to the TELSAT GPRS, install the corresponding driver on the computer. Now the TELSAT GPRS is ready to be used.

  • Page 10: Connecting The Telecomms Equipment

    Stop bits If you want to connect your computer via its USB interface instead of its COM port to the TELSAT GPRS, please first install the drivers and then plug in the USB cable. You can connect here analogue telephones. (Default for...
  • Page 11 If the power supply adapter is disconnected, the TELSAT GPRS is shut down. Even if the TELSAT GPRS is powered by the internal battery (in case of a mains failure), the power supply adapter shall be connected to the TELSAT GPRS.

  • Page 12: Enter The Pin Number

    To enter the PIN use a telephone set connected to the Phone port or the Fax/Modem/Phone port of the TELSAT GPRS. Use the telephone to enter the PIN (by sending DTMF codes to the TELSAT GPRS) just as you would dial a number: When you pick up the handset (go off hook), you will hear a recurrent short beep tone, that prompts for the PIN.

  • Page 13: Autopin Option

    Please enter a new PIN here. Allowed PIN numbers are 0000 to 99999. npin Wall-mounting The TELSAT GPRS is intended to be mounted on the wall. You can fix it to the wall with screws. To mount the device on the wall, first disconnect all the cables. In particular make sure that the power cable is not connected.

  • Page 14: Operation: Making And Answering Telephone Calls

    Operation: Making and answering telephone calls Operation: Making and answering telephone calls Though you can connect many of devices to the TELSAT GPRS only one call - incoming or outgoing - is possible at a time, because there is only a single "wireless"...

  • Page 15: Call A Remote Party

    If an active connection (GPRS, GSM data, Fax or another voice connection) has already been established using the TELSAT GPRS and you try to make a call, you will hear a busy signal since another device is currently using the only "wireless"...

  • Page 16: Option: Having Two Calls At The Same Time

    - the duration depends on the network - the second call is transferred to the voice mail box (Call Forwarding on No Reply - CFNRy), if this feature is enabled. Otherwise the calling party will hang-up, because his call is not answered. TELSAT GPRS...
  • Page 17 The active call will change to Call Hold state and vice versa. ⇒ • Transform the two calls in a 3 parties call (multi party call): • Press the following keys in sequence: You can configure the telephone functions according your needs. See Configuration page 23. TELSAT GPRS...

  • Page 18: Operation: Send And Receive Fax With A Facsimile Device

    TELSAT GPRS. It will indicate this by both FAX Warning LEDs rapidly flashing (see The LEDs on the device on page 8). The TELSAT GPRS will do some retries to deliver the rest of the received facsimile. If it is not successful, it continues to indicate this by both FAX Warning LEDs rapidly flashing.

  • Page 19: In Case Of A Fax Warning

    Operation: Send and receive fax with a facsimile device In case of a FAX Warning If both FAX Warning LEDs are rapidly flashing, the TELSAT GPRS is indicating that it could not transfer a received fax to the connected facsimile device completely (see above).

  • Page 20: Operation: Analogue Modem Connections

    Operation: Analogue Modem connections With an analogue modem connected to the Fax/Modem/Phone port of the TELSAT GPRS you can send and receive data to/from a remote modem being connected to an analogue telephone line or to/from a GSM modem. Please install and operate the modem in accordance to its user manual and the manual of the software you run on the computer connected to the modem.

  • Page 21: Operation: Send And Receive Fixed Network Sms

    Operation: Send and receive fixed network SMS Operation: Send and receive fixed network SMS If you have connected a telecomm equipment to the TELSAT GPRS that is capable of sending and receiving fixed network SMS (see note), you can use the fixed network SMS (SMS = Short Message Service).

  • Page 22: In Case Of Error

    Operation: Send and receive fixed network SMS In case of error In case of error the TELSAT GPRS can send an error report on Sending a SMS the telecomms equipment you have used to send the SMS. You can activate or deactivate this function (see page 36).

  • Page 23: Configuration

    Configuration Configuration Your TELSAT GPRS is a sophisticated device with a wide range of modes of operation. You have to decide which operation modes are appropriate for your needs and then enable them by configuring the TELSAT GPRS. The configuration...

  • Page 24: Ports For Incoming Calls; Volume Of Voice Signal

    To change the setting enter the following sequence: Phone port: Description: 000000 Default access code: Volume sent to *5 ACCESS 001 VV # remote party Volume of voice *5 ACCESS 002 VV # signals received from remote party TELSAT GPRS...
  • Page 25 You want to increase the volume of voice signals received from the remote party when you use the Phone port: Lift up the handset *5 000000 002 03 # then enter: and wait for the confirmation tone then hang-up the handset TELSAT GPRS...

  • Page 26: Configuration Of Network Services

    Depending on the GSM network you use and the subscription you have, there are several services like Call Forwarding etc. available. You can activate/ deactivate these services through the TELSAT GPRS. The configuration is stored by the network but not by the TELSAT GPRS.

  • Page 27: Call Forwarding If Busy (Cfb)

    If Call forwarding if busy is activated, incoming calls will be forwarded to the configured telephone number, if the TELSAT GPRS is just busy in performing a telephone, fax or data call when calls come in. You can configure this for each type of call (voice, data, fax) independently.

  • Page 28: Call Forwarding If No Answer (Cfnry)

    : Incoming phone calls will be forwarded. <call_type> = : Incoming fax calls will be forwarded. <call_type> = : Incoming data calls will be forwarded. Both prefix commands are supported to activate the service. Both prefix commands are supported to deactivate the service. TELSAT GPRS...

  • Page 29: Call Forwarding If Not Accessible (Cfna)

    If call forwarding if not accessible is activated, incoming calls will be forwarded to the configured telephone number, if your TELSAT GPRS is not accessible in the GSM network so that the call can not be answered by telephone, fax or data device. You can configure this for each type of call (voice, data, fax) independently.

  • Page 30: Check Status For Call Forwarding And Call Waiting

    Description: Status on / DTMF code correct ___ Beep ____ Beep Status off / DTMF code correct ___ Beep _ Beep____ Beep DTMF code not correct or service not provided ___ Beep_ Beep by the network TELSAT GPRS...

  • Page 31: Fax-Configuration

    So in the case of faulty fax transmission the TELSAT GPRS will send an error message report to your facsimile device to correct this problem. Only if you are not receiving such an error message report, you can be sure, that the fax was transmitted successfully.

  • Page 32: Disable Modem/Phone On Fax/Modem/Phone Port

    To change the setting enter the following sequence: Description: 000000 Default access code: Receive data call on the *5 ACCESS 010 02 # Fax/Modem/Phone port Receive data call on the *5 ACCESS 010 03 # PC port: RS-232 or USB (Default) TELSAT GPRS...

  • Page 33: Sms Configuration

    Receive SMS on the *5 ACCESS 019 01 # Phone port (fixed network SMS) Receive SMS on the *5 ACCESS 019 02 # Fax/Modem/Phone port (fixed network SMS) Receive SMS on the PC- *5 ACCESS 019 03 # port (Default) TELSAT GPRS...

  • Page 34: Configuration For Fixed Network Sms Protocol 1

    Your fixed network SMS telephone needs the telephone number of the SMS centre. Choose any number and configure this number in both, your telephone and the TELSAT GPRS. For the configuration of the TELSAT GPRS please enter the sequence below: 000000 Default access code: <SMS_...

  • Page 35: Configuration For Fixed Network Sms Protocol 2

    SMS centre. One number to send SMS and one number to receive SMS. Choose any number and configure two numbers in both, your telephone and the TELSAT GPRS. First configure the SMS centre number for sending SMS by entering the following sequence:...

  • Page 36: Enable/Disable Error Report

    8.6.4 Enable/Disable error report If the TELSAT GPRS cannot deliver a SMS to the remote station, there it can send an error report to the telecomms equipment you have used to send the SMS. You can activate or deactivate this function.

  • Page 37: Additional Configuration

    8.7.2 Dialling Timeout The TELSAT GPRS must wait until you have dialled the complete telephone number before it will establish the connection to the remote station. To detect the end of your dialling it waits for a certain duration of time (the dial timeout) after each entered digit.

  • Page 38: Flash Signal Detection (Used To Manage Two Calls Simultaneously)38

    Flash signal of a telephone differs from the standard the TELSAT GPRS is configured for by default. If the TELSAT GPRS does not detect the Flash signal of your telephone in the right way please adjust the setting of the TELSAT...
  • Page 39 Configuration Description: 000000 Default access code: *5 ACCESS 018 0 # SMS configuration OFF SMS configuration ON *5 ACCESS 018 1 # (Default) TELSAT GPRS...

  • Page 40: Installing The Telsat Gprs Modem Driver On A Windows-Pc

    Installing the TELSAT GPRS modem driver on a Windows-PC Installing the TELSAT GPRS modem driver on a Windows-PC If you connect your PC to the TELSAT GPRS via the RS-232 interface or via the USB interface you have the following facilities: •...
  • Page 41 Installing the TELSAT GPRS modem driver on a Windows-PC 1. The TELSAT GPRS must not be connected to your computer. Start your computer. 2. Insert the provided CD-ROM into the CD-ROM drive of your computer. 3. Click Start, Execute... In the Execute dialogue click Browse and switch to the CD- ROM drive.
  • Page 42 Installing the TELSAT GPRS modem driver on a Windows-PC Click Next (remember the Destination Folder) After copying the following dialogue is displayed. Click Finish 4. Now connect the TELSAT GPRS to a USB plug of your computer. TELSAT GPRS...
  • Page 43 Installing the TELSAT GPRS modem driver on a Windows-PC 5. When Windows detects the new device it prompts for a driver via the Found New Hardware Wizard: Select Install from a list or specific location (Advanced), then click Next >.
  • Page 44 Installing the TELSAT GPRS modem driver on a Windows-PC Click Finish. TELSAT GPRS...
  • Page 45 Installing the TELSAT GPRS modem driver on a Windows-PC Select Install from a list or specific location Select Install from a list or specific location (Advanced), (Advanced) then click Next >. Select the folder the installation program has created in step 5:...
  • Page 46 Installing the TELSAT GPRS modem driver on a Windows-PC 10. The serial port driver for the USB interface will be installed. 11. When this dialogue is displayed: Click Continue Anyway. TELSAT GPRS...
  • Page 47 13. Find out what number the new COM port has. Explanation: Afterwards you have to install the modem driver of the TELSAT GPRS. When doing so you have to select the COM port the modem driver shall use. So you have to know: Is it COM3, COM4, COM5...?
  • Page 48 Installing the TELSAT GPRS modem driver on a Windows-PC Click the +-sign next to Ports, if necessary. Look for TIUMP USB Serial Port (COM...) Is it COM3, COM4, COM5 ...? TELSAT GPRS...
  • Page 49 Installing the TELSAT GPRS modem driver on a Windows-PC You want to connect the TELSAT GPRS • to a USB plug of your computer, then install # 1. the USB driver (page 40) 2. the modem driver • to a COM port of your computer, then install...
  • Page 50 Installing the TELSAT GPRS modem driver on a Windows-PC 4. The Hardware Wizard will be displayed to install a new modem. When this dialog is displayed... Select Don't detect my modem; I will detect it from a list Select Don't detect my modem; I will detect it from a list and then click on Next>.
  • Page 51 USB Serial Port look up the number of the created COM port # page 45. When you are asked to choose the COM port, select the COM port of your coputer that is connected to the TELSAT GPRS. TELSAT GPRS...
  • Page 52 Installing the TELSAT GPRS modem driver on a Windows-PC 8. When this dialog is displayed... Dr. Neuhaus TELSAT GPRS Click on Continue Anyway Click Finish. 10. When the installation is finished the installed modem driver is listed in the Phone and Modem Options dialogue: Example Dr.

  • Page 53: Operation: Internet Via Gprs With A Pc

    • Your GSM provider must provide the GPRS service. While you are using the GPRS function of the TELSAT GPRS for example to surf in the Internet, incoming telephone calls will not be indicated. The telephone number to dial-up the GPRS network is always: *99***1# The APN (Access Point Name) of your GSM provider to the Internet should be predefined in the TELSAT GPRS.
  • Page 54 Operation: Internet via GPRS with a PC The New Connection Wizard is started. Click Next >. Select Connect to Internet Select Connect to Internet and click Next >. TELSAT GPRS...
  • Page 55 Select Set up my connection manually and click Next >. Select Connect using a dial-up modem Select Connect using a dial-up modem and click Next >. If prompted to select the modem select: Dr. Neuhaus TELSAT GPRS. TELSAT GPRS...
  • Page 56 Operation: Internet via GPRS with a PC Write any name that describes the purpose of the Dial-up connection. Then click Next >. *99***1# Enter the phone number for access to the Internet: *99***1# Then click Next >. TELSAT GPRS...
  • Page 57 Operation: Internet via GPRS with a PC Enter your user name and password. Look them up in your subscription. Or ask your GSM telephone company. Click Next >. Click Finish. The installation of the dial-up network connection to the Internet is done. TELSAT GPRS...
  • Page 58 In order to do so, please proceed as follows: 1. Open the Properties dialog box of the dial-up network connection for the COM interface of the TELSAT GPRS. (With the right mouse button click on the connection icon and then select Properties in the context menu.) 2.

  • Page 59: To Connect And Disconnect To/From The Gprs / Internet

    E-Mail program. 1. Click on the icon representing the active connection (down on To disconnect the right side of the screen) with the right mouse button to open the context menu. 2. In the context menu click Disconnect. TELSAT GPRS...

  • Page 60: Operation: Using A Pc To Send And Receive Fax

    Your Personal Computer is directly connected to the TELSAT GPRS via its RS-232 port or its USB port. Make sure that you have installed the modem driver of the TELSAT GPRS (see, page 40). When you connect your PC to the USB port, then the RS-232 port is switched off.

  • Page 61: Operation: Using A Pc To Transmit And Receive Data

    AT commands on page 63. By default an incoming data call comes in at the PC port of the TELSAT GPRS, so that a device connected to this port gets the call. If you want to receive data calls by a modem connected eg.

  • Page 62: Operation: Using A Pc To Send And Receive Sms

    Your Personal Computer is directly connected to the TELSAT GPRS via its RS-232 port or its USB port. Make sure that you have installed the modem driver of the TELSAT GPRS (see, page 40). When you connect your PC to the USB port, then the RS-232 port is switched off.

  • Page 63: For Experienced Users: At Commands

    14 For experienced Users: AT commands 14.1 AT Command Interface The TELSAT GPRS has an AT command interface. Using a terminal program like HyperTerminal (belongs to Windows) on your PC you can • communicate with a remote party (see Operation: Using a PC to transmit and receive data, page 61) and •...
  • Page 64 Output product code ATI[n] ‘RT-3000 DNT8115/8123’ (example) ‘Firmware Version: 1.004’ (example) ‘GSM-Module-Firmware: SAGEM JE3,7D’ (example) Output supported operating modes (see ATB) Identification of the modem and the mobile phone Specifies whether or not the device transmits any result code to ATQ[n] the connected TE.
  • Page 65 = 0: normal operation 1: PC Fax enabled PS attach or detach AT+CGATT=n Parameters: n = 0 detached 1 attached AT+CGDCONT= Define PDP context. APN = Access Point Name Enter the PIN number of the SIM card AT+CPIN=PIN TELSAT GPRS...
  • Page 66 3: registration denied 4: unknown 5: registered <lac>: string type; two byte location area code in hexadecimal format (e.g. "00C3" equals 195 in decimal) <ci>: string type; two byte cell ID in hexadecimal format TELSAT GPRS...
  • Page 67 0: not active 1: active AT+CSQ Displays the Signal Quality Parameters: rssi = 0 -113 dbm or less 1 -111 dbm 2...30 -109... -53 dbm 31 -51 dbm or greater 99 not known or not detectable ber = (in percent) TELSAT GPRS...
  • Page 68 = a numeric parameter which specifies the reliability class peak = a numeric parameter which specifies the peak throughput class mean = a numeric parameter which specifies the mean throughput class TELSAT GPRS...
  • Page 69 8: Up to 128000 (1024 kbit/s) 9: Up to 256000 (2048 kbit/s) mean = a numeric parameter which specifies the mean throughput class AT+CBST= Select bearer service type. This command selects the bearer [speed service name with data rate speed, and the TELSAT GPRS...

  • Page 70: At Command Interface (Sms)

    +CPMS See below. +CSCA See below. +CSMP See below. AT+CMGD – Deleting a message: Deletes the message AT+CMGD=<index> Message storage location <index> Values for: Message storage location on SIM, 1 – n n depends on SIM card capacity TELSAT GPRS...
  • Page 71 1 – 10 n depends on SIM card capacity AT+CMGS – Sending a message Text Mode activated (AT+CMGF=1) Sends the message AT+CMGS=<da><CR> <Txt> <CTRL Z> “Recipient's telephone number” <da> Value for: The text to be sent Value for: <Txt> TELSAT GPRS...
  • Page 72 <mode> Values for: Buffer unsolicited result codes in the device. If ist buffer is full, indications can be buffered in some other place or the oldest indications may be discarded and replaced with new received indications. Not supported TELSAT GPRS...
  • Page 73 The buffered notification are sent. Not supported AT+CPMS – Selecting the SMS memory location: Sets the memory location AT+CPMS= <mem> Calls up the current memory location AT+CPMS? Lists the memory locations supported AT+CPMS=? <mem> Values for: SIM card „SM“ TELSAT GPRS...

  • Page 74: At Command Interface (Sim Application Toolkit)

    +KSTV See below In addition to the listed AT commands, in this operating mode the GSM-Adapter recognises, accepts and acknowledges a series of AT commands which are, however, not executed. These commands are: , ATM ATXn, ATP, ATT TELSAT GPRS...
  • Page 75 Is sent to the module when a command has been received with an incorrect or unmanageable type. Response: OK <type> Type of command received as the payload Values for: of the unsolicited code +KSTC <details> Command details in HEX format TELSAT GPRS...
  • Page 76 <size> AT+KSTIR – Get a data block of an icon instance Sets the parameters AT+KSTIR=<num> Response: +KSTIR:<data>,<checksum> Integer type; block number Values for: <num> string type (in HEX format); data block <data> string type (in HEX format) <checksum> TELSAT GPRS...
  • Page 77 AT+KSTP=? Test command Response: +KSTP:<support>,<setup profile> AT+KSTP? Read command Response: +KSTP:<current profile>,<default profile> AT+KSTP=<support>[,<DTE profile>] Write command Response: <support> Values for: 0 No SIM Application Toolkit support 1 SIM Application Toolkit support <xxx profile> Profile in HEX format TELSAT GPRS...
  • Page 78 Write command Response: <type of response> Values for: 0 final response (other values will be added later) <TLVs> TLVs in HEX format AT+KSTV – Envelope command AT+KSTV=<envelope> Sets the parameter. Response: <envelope> TLVs in HEX format Values for: TELSAT GPRS...

  • Page 79: Configuration Methods

    Configuration methods 15 Configuration methods The complete configuration of the TELSAT GPRS is written in a parameter file called para.ini which is stored in the non-volatile memory of the device. When configuring the TELSAT GPRS, the parameter file para.ini will be modified. The TELSAT GPRS can be configured by following methods: •...
  • Page 80 Port B is the configuration name for the Fax/Modem/Phone port. Port C is the configuration name for the PC port (through USB or RS232). Power Supply Fax machine, Modem or Phone PC via RS232 PC via USB Phone TELSAT GPRS...

  • Page 81: Configuration By Dtmf

    ID that is to be entered when using the telephone in order to set the according parameter value. The table shows also the section and the name of the parameters so that you can change the parameter settings by sending an SMS to the TELSAT GPRS or by editing the para.ini file TELSAT GPRS...
  • Page 82 FLASH CHB_FLASH_MAX *10[ms] DEVICE_ACCESS SMS_CONFIG NO/YES DEVICE_ACCESS SMS_PORT P1/P2 SYSTEM_TIME 235959 hh:mm:ss MOBILE_CONFIG SIMPIN DELETE MOBILE_CONFIG SIMSTATE DELETE DEVICE_ACCESS DTMF_PASSWORD 000000 999999 PSTN_SMS PSTN_SMS_CENTER Phone number Number PSTN_SMS ERROR_REPORT NO/YES PSTN_SMS LOCAL_NUMBER Phone number Number PSTN_SMS SMS_PROTOCOL Protocol TELSAT GPRS...

  • Page 83: Remote Configuration By Sms

    You may change the file para.ini with a configuration SMS. You have to send a SMS to the TELSAT GPRS from a remote location. You can configure up to 5 remote stations that are allowed to send a configuration SMS (see Settings for the configuration access via SMS and FTP, page 86).

  • Page 84: Configuration By Ftp (Local And Remote)

    Configuration by FTP (Local and Remote) The configuration of the TELSAT GPRS is written in the file para.ini that is stored in the memory of the device. You can edit this file with a text editor (capable of writing plain text).
  • Page 85 (CLIR deactivated). So the TELSAT GPRS can check if the calling station is allowed to configure by comparing the signalled telephone number with the numbers in the para.ini.

  • Page 86: Parameters In The File Para.ini: Advanced Configuration

    16.2 Settings for the configuration access via SMS and FTP The TELSAT GPRS must know the remote stations that should be allowed to do remote service or configuration calls by FTP. For SMS remote configuration you can configure if the CLIP is checked or not. You can configure up to 5 stations for SMS and FTP access each.

  • Page 87: Power-Missing Sms

    Can be configured by SMS (see page 83) Can be configured by FTP (see page 84) If the mains power fails, the TELSAT GPRS can send an SMS to a GSM telephone number, which has to be pre-configured in the parameter file.

  • Page 88: Select Port For Incoming Sms

    The baudrate of the Debug-Interface can be configured. The Debug-Interface is not part of a standard product. [SERVICE_IF] BAUDRATE=57600 Section: SERVICE_IF Meaning Parameter Permitted Values Factory Setting Baudrate for debug BAUDRATE 300, 600, 1200, 57600 RS232 2400, 4800, 9600, 19200, 38400, 57600, 115200 TELSAT GPRS...

  • Page 89: Pre-Selection

    “00”. Some countries are using different digits. You can select with the parameter [INTERNATIONAL], which two digit prefix should be converted into the “+” prefix. Section: CALL_MUX Meaning Parameter Permitted Values Factory Setting Conversion to + INTERNATIONAL 00 to 99 TELSAT GPRS...

  • Page 90: Prefix For Analogue Data And Fax Calls

    If your Analogue modem or fax machine dials either the fax or data prefix before the telephone number, the TELSAT GPRS detects that it is an Analogue data or fax call and switches in the correct mode. You can change these prefixes. Please ensure that your chosen prefix differs from all DTMF configuration code.

  • Page 91: Port Allocation

    Success fax after FAX_SUCCESS_REPORT YES, NO completed MOC Section: Meaning Parameter Permitted Factory Values Setting Fax Identification IDENT 20 chars TELSAT GPRS (if remote identification is not available, yet) Disconnect on AC AC_DOWN_DISCONNECT YES,NO power fail TELSAT GPRS...
  • Page 92 FAX_ACCEPT_TIMEOUT=20 Maximum retries for local fax [Can be configured by SMS, FTP] If the TELSAT GPRS has stored a part of a received fax because the connection to the local fax has been interrupted, the TELSAT GPRS will try to resend the stored part of the fax document to the local fax machine automatically.

  • Page 93: Billing Tone Configuration

    16.12 Billing Tone configuration Can be configured by SMS (see page 83) Can be configured by FTP (see page 84) The TELSAT GPRS can generate billing pulses on the Phone port and on the Fax/Modem/Phone port. Enable/Disable This feature can be activated or deactivated for both ports separately [CHA_BIILING_ENABLED, CHB_BIILING_ENABLED].

  • Page 94: Clip Function Configuration

    Can be configured by FTP (see page 84) Can be configured by DTMF (see page 81) When a call comes in and it is ringing the TELSAT GPRS can transmit the telephone number of the calling party to the equipment connected to the Phone port or the Fax/Modem/Phone port.
  • Page 95 Display CLIP Port B CHB_CLIP_ENABLED YES, NO define the delay CHB_RING_CLIP_DELAY 50 to 200 between end of first ring and start of CID (10ms) CHB_SEIZURE_BITS 96 to 300 the amount of seizure bits the amount of mark CHB_MARK_BITS 60 to 205 bits TELSAT GPRS...

  • Page 96: Configuration Of The Flash Signal

    (10ms) The minimum flash CHB_FLASH_MIN 4 - 55 duration. Shorter pulses may be interpreted as parts of pulse-dial! (10ms) The maximum flash CHB_FLASH_MAX 12 - 65 duration. Longer pulses may be interpreted an onhook/offhook! (10ms) TELSAT GPRS...

  • Page 97: Ring Frequency

    Normally you must enter the telephone number completely before the TELSAT GPRS can start dialling. The TELSAT GPRS starts dialling until you do not press any more key on the telephone and after the dial timeout is expired - the duration the TELSAT GPRS waits for any new key stroke.

  • Page 98: Call Wait Tone On/Off

    By default this tone will be generated by the network. If you want that the Ringback tone is generated by the TELSAT GPRS set the following parameter to YES: CHx_LOCAL_CALL_CTRL=YES.

  • Page 99: Telephone And Fax/Modem/Phone Port Impedance

    To set-up GPRS connections, the PDP_CONTEXT for this connection must be specified in the para.ini file. For each GPRS provider an own section has to be created in the parameter file. For some GPRS providers the configuration is already pre- configured: TELSAT GPRS...
  • Page 100 Factory Setting Predefined Provider T-D1 PDP_CONTEXT 1,"IP","internet.t- d1.de","0.0.0.0",0,0 Predefined Provider D2 PDP_CONTEXT 1,"IP","volume.d2gprs.d e","0.0.0.0",0,0 Predefined Provider EPLUS PDP_CONTEXT 1,"IP","internet.eplus.de" ,"0.0.0.0",0,0 Predefined Provider VIAG PDP_CONTEXT 1,"IP","internet","0.0.0.0" ,0,0 New Provider i.e. myGPRS PDP_CONTEXT PDP context as given by the new provider. TELSAT GPRS...

  • Page 101: Clir On/Off

    Can be configured by SMS (see page 83) Can be configured by FTP (see page 84) This function simulates the Polarity reversal feature provided on the Spanish fixed telephone network, but there are some differences, caused by the adaptation to the wireless environment. TELSAT GPRS...

  • Page 102: Hang-Up Delay

    The Microcom Networking Protocol MNP is used for error correction and flow control on the link to the local connected Modem. If you want MNP active set the following parameter as follows: MNP=YES Section: MODEM Meaning Parameter Permitted Values Factory Setting MNP setting YES,NO TELSAT GPRS...

  • Page 103: Maximum Local Modem Speed

    This parameter sets the baudrate used on GSM to connect to remote modem. (Depends on the network and your subscription.) Section: MODEM Meaning Parameter Permitted Values Factory Setting GSM and remote GSM_SPEED 2400, 4800, 9600 automatic modem baudrate TELSAT GPRS...

  • Page 104: Early Connect Of Local Modem

    These parameters force data calls for special numbers on outgoing calls (for modems without correct calling tone) Section: MODEM Meaning Parameter Permitted Values Factory Setting This number forces DATA_NUM_1 Number a data call DATA_NUM_2 (max 30 digits) DATA_NUM_3 TELSAT GPRS...

  • Page 105: Gsm Baudrate Depending On Dialled Number (Number)

    2400, 4800, 9600 automatic the phone number defined by SPEED_NUM Forced baudrate for SPEED_FOR_NUM_2 2400, 4800, 9600 automatic the phone number defined by SPEED_NUM_2 Forced baudrate for SPEED_FOR_NUM_3 2400, 4800, 9600 automatic the phone number defined by SPEED_NUM_3 TELSAT GPRS...

  • Page 106: Fixed Network Sms

    SMS can not be delivered Protocol parameter ACK_INFO Reserved Reserved Protocol parameter ACK_PAYLOAD Reserved Reserved Protocol parameter ALL_MSG_AT_ONCE Reserved Reserved Telephone number LOCAL_NUMBER Phone number of the PSTN-SMS- Center for RX (Can be configured by DTMF (see page 81)) TELSAT GPRS...

  • Page 107: Frequency Band Selection Gsm 900, Dcs 1800, Pcs 1900

    900 MHz or DUAL_US Autoselect 900/1900 MHz 1800 MHz networks. Autoselect 900/1800/1900 MHz The TELSAT GPRS with 1900 MHz antenna should only be used in 1900 MHz networks. If you do not know, if your GSM networks operates at...
  • Page 108 ; number of service centers: MAX_SRV_CALLERS in project_defs.h ; SMS / DTMF [DEVICE_ACCESS] DEVICE_PASSWORD=000000 DTMF_PASSWORD=000000 SERVICE_CLIP_0= SERVICE_CLIP_1= SERVICE_CLIP_2= SERVICE_CLIP_3= SERVICE_CLIP_4= ; POWER_REPORT: YES or NO, default is YES POWER_REPORT=NO POWER_REPORT_NR= SMS_PORT=C ; SMS_CONFIG: YES or NO, default is YES SMS_CONFIG=YES TELSAT GPRS...
  • Page 109 ; time in seconds, to wait for next retry INTERNATIONAL=00 FAX_SUCCESS_REPORT=NO EMERGENCY_1=112 EMERGENCY_2=112 EMERGENCY_3=112 ; prefix to force data/fax call (do NOT use DTMF config sequences) DATA_PREFIX=*** FAX_PREFIX=### [FAX] IDENT=TELSAT GPRS ;FAXAPP_DEBUG=COM ;T30_DEBUG=COM [PSTN_SMS] SMS_PROTOCOL=1 PSTN_SMS_CENTER=0193010 RING_TIMEOUT=600 DELIVERY_DELAY=3000 ERROR_REPORT=YES ;*** special parameters for protocol 1...
  • Page 110 CHA_16KHZ_BURST=YES ;settings for channel b CHB_BILLING_ENABLED=NO CHB_PULSE_DURATION=20 CHB_PULSE_DELAY=100 CHB_PULSE_LEVEL=1 ;12kHz and 16kHz. default: 16kHz CHB_16KHZ_BURST=YES [CLIP] ;settings for channel a CHA_CLIP_ENABLED=YES CHA_RING_CLIP_DELAY=50 CHA_SEIZURE_BITS=300 CHA_MARK_BITS=180 ;settings for channel b CHB_CLIP_ENABLED=YES CHB_RING_CLIP_DELAY=50 CHB_SEIZURE_BITS=300 CHB_MARK_BITS=180 [FLASH] ;settings for channel a CHA_FLASH_MIN=7 TELSAT GPRS...
  • Page 111 [DIALING] ;settings for channel a ;AUTO, REAL600, REAL900, COMPLEX CHA_INPUT_IMPEDANCE=COMPLEX CHA_POLARITY_REV=NO CHA_MTC_HOOK_DELAY=NO CHA_MTC_HOOK_TIMEOUT=6000 CHA_FAST_DIAL=NO CHA_DIAL_TIMEOUT=600 CHA_LOCAL_CALL_WAIT=NO CHA_LOCAL_CALL_CTRL=NO CHA_TX_VOICE_LEVEL=-7 CHA_RX_VOICE_LEVEL=-7 ;settings for channel b CHB_INPUT_IMPEDANCE=COMPLEX CHB_POLARITY_REV=NO CHB_MTC_HOOK_DELAY=NO CHB_MTC_HOOK_TIMEOUT=6000 CHB_FAST_DIAL=NO CHB_DIAL_TIMEOUT=600 CHB_LOCAL_CALL_WAIT=NO CHB_LOCAL_CALL_CTRL=NO CHB_TX_VOICE_LEVEL=-7 CHB_RX_VOICE_LEVEL=-7 [GPRS_CONFIG] PROVIDER= SPECIAL_CGATT=NO [T-D1] PDP_CONTEXT=1,"IP","internet.t-d1.de","0.0.0.0",0,0 TELSAT GPRS...
  • Page 112 VERSION_PARA_INI=1.031 ;MOB_DEBUG_TO_LOG=NO [MODEM] ;; MNP: YES or NO; default YES MNP=YES ;; max. local speed: 300, 1200, 2400, 4800, 9600, 14400; default 9600 ;MAX_SPEED=14400 ;; min. local speed: 300, 1200, 2400, 4800, 9600, 14400; default 0 (means 300) TELSAT GPRS...
  • Page 113 ;DP_DEBUG=COM ;; special numbers DATA_NUM_1= DATA_NUM_2= DATA_NUM_3= [SPECIAL_MODEM] ; if uncommented: for SPEED_NUM GSM-speed is set as defined in SPEED_FOR_NUM ;SPEED_NUM= ;SPEED_FOR_NUM= ;SPEED_NUM_2= ;SPEED_FOR_NUM_2= ;SPEED_NUM_3= ;SPEED_FOR_NUM_3= [AT_PARSER] ECHO=YES VERBOSE=YES QUIET=NO FLOW_CONTROL=YES DCD_CONTROL=YES DTR_CONTROL=YES ANSWER_RING=0 BAUDRATE=57600 PDP_CONTEXT= CNMI_SETTING=0,0,0,0,0 SMS_TEXT_MODE=NO TELSAT GPRS...

  • Page 114: Configuration Of Tones

    Configuration of Tones 17 Configuration of Tones Tones generated by the TELSAT GPRS can be configured by editing the parameter file tone.ini. You can access this file in the same way as the parameter file para.ini. Refer to page 84.
  • Page 115 RING signal CHB_RING Dial tone CHB_DIAL Ring back tone CHB_CALL_CTRL Busy tone CHB_BUSY_TONE Call wait tone CHB_CALLWAIT Programming CHB_ACPT_ -100 acceptance tone PROG Programming non- CHB_NACPT_ -100 acceptance tone PROG PIN last try tone CHB_LAST_PIN SIM missing tone CHB_SIM_MISS TELSAT GPRS...

  • Page 116: How To Program A New Timing

    % 16 = tone off for 16*10ms = 160ms % 16 = tone on for 16*10ms = 160ms % -4 = timing sequence terminator. Go 4 steps back in timing sequence -> next timimng is the tone off for 800*10ms TELSAT GPRS...

  • Page 117: Example-File

    All programmed timings, levels and frequencies were read from TONE.INI only once at the startup of the device. After changes have been made, a reset of the device must been done, to use them. 17.2 Example-File: ;TELSAT GPRS Tone-Parameter File [TONES] ;settings for channel a CHA_DIAL_TONE=440 CHA_CALL_CTRL=440...
  • Page 118 ;timing-sequence-terminators: -100 -> end of sequence; -2 -> 2 steps back; -4 -> 4 steps back ... ;settings for channel a CHA_RING=100,400,-2 CHA_DIAL=100,0,-2 CHA_CALL_CTRL=150,350,-2 CHA_BUSY=50,50,-2 CHA_CALLWAIT=40,800,16,16,16,-4 CHA_ACPT_PROG=10,10,-100 CHA_NON_ACPT_PROG=10,50,10,50,-100 CHA_LAST_PIN=50,50,10,50,-4 CHA_MISS_SIM=10,50,-2 ;settings for channel b CHB_RING=100,400,-2 CHB_DIAL=100,0,-2 CHB_CALL_CTRL=150,350,-2 CHB_BUSY=50,50,-2 CHB_CALLWAIT=40,800,16,16,16,-4 CHB_ACPT_PROG=10,10,-100 CHB_NON_ACPT_PROG=10,50,10,50,-100 CHB_LAST_PIN=50,50,10,50,-4 CHB_MISS_SIM=10,50,-2 [GENERAL] VERSION_TONE_INI=1.031 TELSAT GPRS...

  • Page 119: Logfile

    Logfile 18 Logfile Relevant events of the TELSAT GPRS are reported in a Logfile. You can access this Logfile in the same way as the parameter file para.ini. Refer to page 84. The name of the Logfile is: logfile.$rf Close the FTP connection after the Logfile is copied to your PC. You can open the Logfile using a standard text editor.

  • Page 120: Update The Firmware

    (connected to the USB or RS-232 port) or from remote. The approach is just as if you want to configure the TELSAT GPRS by uploading the edited configuration file para.ini by FTP - see 15.3 Configuration by FTP (Local and Remote), page 84.

  • Page 121: Connection Sockets

    Operating Ground Modem Ready Request To Send Modem Ready to Send Incoming Call The serial interface is operated at a data rate of 57600 bps. The data format is 8-N-1 (8 data bits, no parity bit, 1 stop bit). TELSAT GPRS...

  • Page 122: Technical Data

    Humidity 0-95%, non-condensing Approvals CE (Residential, commercial and light-industrial-environment); R&TTE (GSM); GSM/GPRS-Module with GCF-Approval; Safety according to EN 60950 Mechanics Dimensions : ca.195 x 151 x 38 mm (L x W x D); weight ca. 620g (incl. battery and antenna) TELSAT GPRS...

Table of Contents