Media5 Mediatrix 4102 Installation Manual
Hide thumbs Also See for Mediatrix 4102:

Advertisement

Warning:
In the following installation procedures, do not disconnect the
Mediatrix 4102 while the LEDs are flashing.
Thank you for choosing the Mediatrix 4102. This Quick Start will help you to properly connect all of the cables to the Mediatrix 4102 and access its web
interface.
Please read the Mediatrix 4102 Hardware Installation Guide for detailed installation information and the Mediatrix 4102 Software
Configuration Guide for in-depth configuration information.
Step 1

Connecting Cables

The following describes how to connect the various cables to the Mediatrix 4102.
Before you begin, make sure that you have a working network connection. Then follow these steps to install the Mediatrix 4102.
1.
Before you begin, be sure that the Mediatrix 4102 is powered off.
2.
Connect the power cord to its connector on the Mediatrix 4102. Do not connect
the other end of the power cord to an electrical outlet.
3.
Connect analog telephones or fax machines into the
Fax 2
connectors.
Use a standard telecommunication cord with a minimum of 26 AWG wire size.
4.
Connect a 10/100 BaseT Ethernet RJ-45 cable into the
interface that supplies TCP/IP network access (e.g., router, switch, hub or computer).
You can either use a crossover or straight Ethernet cable because it performs automatic MDI / MDIX detection.
Use a standard telecommunication cord with a minimum of 26 AWG wire size.
5.
Connect a 10/100 BaseT Ethernet RJ-45 cable into the
a computer.
You can either use a crossover or straight Ethernet cable because it performs automatic MDI / MDIX detection. Use a standard
telecommunication cord with a minimum of 26 AWG wire size.
Step 2
IP Address Discovery or Configuration
The purpose of this section is to be able to contact the Mediatrix 4102's web interface to start with unit configuration.
Once the physical connection is complete, you will need to power on the Mediatrix 4102 and find out the IP address it is using. The Mediatrix 4102's IP
address can be set either dynamically or statically. The default behaviour of the Mediatrix 4102 is to try to obtain a dynamic IP address through a DHCP
server.

Dynamic IPv4 Address Discovery

Before connecting the Mediatrix 4102 to the network, Media5 strongly suggests that you reserve an IP address in your DHCP server for the unit you are
about to connect. DHCP servers reserve IP addresses for specific devices by using a unique identifier for each device. The Mediatrix 4102's unique
identifier is its media access control (MAC) address. The MAC address appears on the label located on the bottom side of the unit.
Note:
Make sure any IPv4 DHCP-provided address is outside of 192.168.0.x or otherwise, contact the unit on the LAN port and change the LAN
IP address for an address that does not clash with the DHCP-provided address.
© 2012, Media5 Corporation
Phone-Fax 1 and Phone-
WAN
connector of the Mediatrix 4102; connect the other end to a compatible Ethernet
LAN
connector of the Mediatrix 4102 and connect the other end to the network card of
Discover the Power of
Mediatrix 4102/4102S
Installation – SIP
4
3
5
5
2
Document Revision 16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Mediatrix 4102 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Media5 Mediatrix 4102

  • Page 1: Dynamic Ipv4 Address Discovery

    In the following installation procedures, do not disconnect the Mediatrix 4102 while the LEDs are flashing. Thank you for choosing the Mediatrix 4102. This Quick Start will help you to properly connect all of the cables to the Mediatrix 4102 and access its web interface.
  • Page 2: Default Static Ipv4 Ip Address Configuration

    Subnet Mask to 255.255.255.0. Restart the computer. Power on the Mediatrix 4102 by connecting the other end of the power cord to an electrical outlet. The electrical outlet must be installed near the Mediatrix 4102 so that it is easily accessible.
  • Page 3: Access Web Interface

    Step 3 Access the Mediatrix 4102 Web Interface The Mediatrix 4102 may have one of two versions of the SIP application available. You can distinguish them by the login page used. Version #1 In your web browser’s address field, type the IP address of the Mediatrix 4102: ...
  • Page 4 If you have Administrator credentials, you can use the Access admin site and Access user site links in the top right corner to switch between the two web interfaces. Step 4 End User Technical Support Media5 works through its partners to resolve technical support issues. All end users requiring technical support are encouraged to contact their vendor directly. Page 4 Installation Quick Start...

This manual is also suitable for:

Mediatrix 4102s

Table of Contents