Advertisement
This appliance should be connected
directly to the fused disconnect
(or
circuit breaker box) through flexible, arm&red or
non-metallic
sheathed, copper cable (with
grounding wire). The flexible armored cable
from the appliance should be connected directly
to the junction box.
IE.I
Locate the junction box to allow as
much slack in the cable as oossible
between the junction box and the ap'pliance so
that the oven can be moved if servicing is ever
necessary. Do Not cut the conduit.
El
A U.L.-listed conduit connector must
'
be provided at the junction box.
B-l
A wiring diagram is included in the
W Tech Sheet. The Tech Sheet is located
behind the oven control panel.
Electrical
connection
Electrical
Shock Hazard
l
Electrical
ground
is required
on this
appliance.
l
Do Not connect
to the electrical
supply
until appliance
is permanently
grounded.
l
Disconnect
power to the junction
box
before making the electrical
connection.
l
This appliance
must be connected
to a
grounded,
metallic,
permanent
wiring
system, or a grounding
connector
should
be connected
to the grounding
terminal
or wire lead on the appliance.
Failure to do so could result in a fire,
personal
injury or electrical
shock.
This appliance is manufactured
with white
(neutral) power supply wire and a cabinet-
connected green grounding wire twisted
together.
Connect the appliance cable to the junction box
through the U.L.-listed conduit connector.
Complete electrical connection
according to
local codes and ordinances.
A. Where local codes permit...
Connecting
the cabinet-grounding
conductor
to the neutral (white) junction
box wire:
Junction
Cable from
power supply
Figure 1
Cable
from oven
connector
Grounded
Neutral
1. Disconnect
the power supply.
2. Remove the terminal block cover.
3. Connect together 3 wires: green and white
appliance cable wires and the neutral (white)
wire in junction box.
4. Connect the two black wires together; then
the two red wires together. See Figure 1.
B. Where local codes Do Not
permit...
Connecting
the cabinet-grounding
conductor
to the neutral (white) junction
box wire:
Junction
Cable from
. --.
-..-,
green
wires
listed
Cable
conduit
from oven
connector
Figure 2
Ungrounded
Neutral
1. Disconnect
power supply.
2. Separate the green and white appliance
cable wires.
3. Connect the white appliance cable wire to the
neutral (white) wire in the junction box.
4. Connect the two black wires together: then
the two red wires together. See Figure 2.
5. Connect the green or bare grounding wire
from the appliance cable to a grounded wire in
the junction box.
C. If connecting
to a four-
wire electrical
system...
Do Not connect
the cabinet-grounding
conductor
to the neutral (white) junction
box wire.
Junction
Cable fron
I
L-..
power supply
conduit
Figure 3
connector
1. Disconnect
the power supply.
2. Separate the green (or bare) and white
appliance cable wires.
3. Connect the white appliance cable wire to the
neutral (white) wire in the junction box.
4. Connect the two black wires together; then
the two red wires together. See Figure 3.
5. Connect the green appliance cable wire to
the green grounding wire in the junction box.
Now start...
With oven in kitchen.
(1(
Remove shipping materials, tape, and
W protective film from microwave oven.
Do Not remove shipping
base at this time.
121
Remove the racks and other parts from
n
inside the oven. Remove the air grille
taped to the top or side of oven.
Personal
Injury/Product
Damage Hazard
l
Use both hands to remove oven door.
l
Grasp only the sides of oven door.
i
l
Do Not use handle or any portion
of the
front frame or trim for lifting.
l
Because of the weight
and size of the
I
oven, two or more people are needed to
move and safely install the oven.
Failure to properly
grasp the oven door or
to lift oven properly
could result in
damage to the product
or personal
injury.
131
w
Completely open the oven door.
Remove the two oven door screws.
(Not all models have oven door screws.)
14.1
Close oven door to the broil position. Grasp the
sides of the oven door and pull the door up and
out of the hinge slots to remove. Set door aside.
Floor Damage
Before moving
oven across floor, check
that oven is on shipping
base or slide
oven onto cardboard
or hardboard.
Failure to follow these instructions
may
result in damage to floor covering.
1
I
151
Turn power supply off. Move oven close
' to final position. Remove and discard
shipping base, cardboard or hardboard. Feed
appliance cable through the opening in cabinet.
Make electrical connection.
See "Electrical
requirements"
and "Electrical connection"
sections, Panels A and B.
Product
Damage
Carefully
push against
the seal area of the
oven front frame when pushing
the oven
into the cabinet.
Do Not push against outside
edges.
Failure to follow these instructions
can
result in damage to oven finish.
Panel B
Advertisement
