Related Manuals for Vantec CB-U320GNA
Summary of Contents for Vantec CB-U320GNA
-
Page 1: User Manual
USB 3.0 To Dual Gigabit Ethernet Network Adapter CB-U320GNA User Manual Ver. 1.00 All brand names and trademarks are properties of their respective owners. -
Page 2: Table Of Contents
2.2 Driver Installation ............... 8 2.2.1 Installation for Windows ............8 2.2.2 Installation for Mac OS ............9 2.3 Hardware Verify ............... 11 2.3.1 Verifying for Windows ............11 2.3.2 Verifying for Mac OS X ............12 CB-U320GNA Page 2... -
Page 3: Chapter 1: Introduction
Chapter 1: Introduction 1.1 Product Introduction Vantec introduces the USB 3.0 To Dual Gigabit Ethernet Network Adapter bringing you Dual Gigabit Ethernet through a single USB port. With the ease through a single USB connection, you can gain gigabit network speeds of... -
Page 4: Features
Dual Gigabit Ethernet ports through a single USB connection Compliant with Universal Serial Bus 3.0 Specification, Revision 1.0 Compatible with USB Specification, Revision 2.0 Supports CDC-ECM Supports crossover detection, auto-correction, polarity correction, adaptive equalization, cross-talk+echo cancellation, and timing recovery CB-U320GNA Page 4... - Page 5 Microsoft NDIS5, NDIS6 Checksum Offload (IPv4, IPv6, TCP, UDP) and Segmentation Task-offload (Large send v1 and Large send v2) support IEEE Supports full duplex operation with IEEE 802.3x flow control and half duplex operation with back-pressure flow control CB-U320GNA Page 5...
- Page 6 Supports Microsoft WPD (Wake Packet Detection) Supports Protocol Offload (ARP & NS) Intel CPPM (Converged Platform Power Management) Supports L1 with 3ms BESL (USB 2.0) Dynamic LTM messaging (USB 3.0) Supports U1/U2 (USB 3.0) CB-U320GNA Page 6...
-
Page 7: System Requirements
10.6 or Greater (Intel-based Mac) / Latest Linux OS USB 3.0 Port preferred to get maximum speed 1.4 Package Contents Vantec USB 3.0 To Dual Gigabit Ethernet Adapter Drivers CD Quick Installation Guide Chapter 2: Getting Started 2.1 Hardware Installation... -
Page 8: Driver Installation
Network Adapter to your PC before the install. 2.2.1 Installation for Windows Insert the provided CD into your optical drive. Browse to the CB-U320GNA Folder and select the Windows OS. Start the driver installation by clicking on the setup program. *Note: Actual image may vary... -
Page 9: Installation For Mac Os
Follow the instructions on the screen to install the drivers. 2.2.2 Installation for Mac OS Insert the provided CD into your optical drive. Browse to the CB-U320GNA Folder and select the Mac Folder. Start the driver installation by clicking on the installation pkg. *Note: Actual image may vary Follow the instructions on screen to install the driver. - Page 10 Review and click continue thru the installation. Use the default setting. Enter Password to continue CB-U320GNA Page 10...
-
Page 11: Hardware Verify
2.3.1 Verifying for Windows Click on the “Device Manager” tab in the Windows Control Panel. Start > Control Panel > Device Manager Entry “Network adapters” item, you should see the following devices installed with no exclamation points or question marks. CB-U320GNA Page 11... -
Page 12: Verifying For Mac Os X
Open the System Profiler by clicking the Apple symbol in the top left corner, selecting About this Mac, then select System Report Expand the “Network” section. With the cable connected, you should see the following devices in the list. CB-U320GNA Page 12...