Page 25
BLUES GROUND HOT ( + ) COLD () SLEEVE GROUND RING HOT ( + ) COLD () GROUND SIGNAL SLEEVE...
Page 26
BLUES SPECIFICHE TECNICHE SEZIONE LIVELLI & DATI CONNETTORI CANALE DI INGRESSO MONO Ingresso MIC da -45 a -15 dB XLR-F bilanciato sensibilità 30 dB guadagno 1 kohms impedenza Ingresso LINE da +10 a -20 dB JACK bilanciato sensibilità 30 dB guadagno 10 kohms impedenza...
MONO input channel BLUES MONO input channel 1. MIC INPUT Balanced XLR connector (from -15dB to -45dB /1kOhm): receives the microphone input signal on the channel. LINE 2. LINE INPUT Balanced JACK connector (from +10dB to 20dB /10kOhms): receives the line input signal on the channel.
STEREO input channel BLUES 10. PEAK Luminous peak indicator: lights up when the signal is near (-6dB) distortion point (CLIP). 11. SIGN Luminous signal indicator: this green LED lights up with a -15dB input signal, enabling the operator to monitor the presence of a signal on the input. 12.
MASTER section BLUES MASTER section 1. AUX OUT Balanced JACK connector (+4dB): this connector feeds out the sum of the signals arriving from the relative AUX sends of the input channels. The AUX send is POST-FADER and therefore mainly intended for use with OUTBOARD EFFECTS. MONO 2.
MASTER section BLUES 10. MONO MONO Pot for controlling the MONO output level: a second master which has the same MIX program, but in mono. 11. MIX LEFT & RIGHT Two 60mm. faders for control of the general volume. 12. PHONES OUT STEREO JACK headphone output connector: only stereo headphones with a minimum impedance of 30 Ohms should be connected to this output.
MASTER section BLUES The BLUES DSP is a DIGITAL STEREO MULTI-EFFECT made up of two distinct sections: REVERB Section é ROOM (PRESETS 1-4) HALL (PRESETS 5-8) VOCAL (PRESETS 9-12) PLATE (PRESETS 13-16) MULTIEFFECT Section é CHORUS (PRESET 17) FLANGER (PRESETS 18-19) PHASER (PRESETS 20-21) STEREO DELAY (PRESETS 22-24)
MASTER section BLUES DSP CONTROL PANEL 1. DISPLAY 2-digit display: this displays the PRESET number. 2. PEAK Luminous peak indicator: lights up when the input signal on the corresponding section reaches a level of 6dB below distortion point (CLIP). 3. TAP ON LED DIGITAL SIGNAL PROCESSOR Central luminous BPM indicator (TAP ON): flashes when the joystick is moved to the left and procedure for acquiring the tempo is enabled (only with PRESET 32...
3 LPS - P.A. SYSTEM é This third curve has been specifically designed for 1 WARM 2 VOCAL compensating and optimizing the response of the LEM range of LPS PLUS & LPS 3 LPS - LEM P.A. system ACTIVE loudspeaker enclosures.
Connector cables BLUES CONNECTION CABLES GROUND HOT ( + ) COLD () Balanced XLR-M connector SLEEVE GROUND RING HOT ( + ) COLD () Balanced JACK connector GROUND SIGNAL SLEEVE RCA pin connector PS 30 POWER SUPPLY UNIT 1. MAINS POWER CORD Cord for connection to the mains power supply 2.
TECHNICAL SPECIFICATIONS SECTION LEVELS & DATA CONNECTORS MONO INPUT CHANNEL sensitivity from -45 to -15 dB Balanced XLR-F gain 30 dB input impedance 1 kohms sensitivity from +10 to -20 dB LINE Balanced JACK gain 30 dB input impedance 10 kohms HIGH ±15 dB @10 kHz LOW ±15 dB @ 70 Hz STEREO INPUT CHANNEL...
Page 41
Sales Division: 47037 S.Giovanni in Marignano (FO) – via delle Rose, 12 – tel. 0541/959511 – tlx 550555 GMUSIC – fax 0541/957404...
Need help?
Do you have a question about the blues series and is the answer not in the manual?
Questions and answers