Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for LEM SWING14P
Summary of Contents for LEM SWING14P
-
Page 2: Important Safety Instructions
The lighting flash with arrowshad symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltages” within the product’s enclosure, that may be of sufficient magnitude to constitute a risk of electric schok to persons. The exclamation point within an equilater triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the... -
Page 3: Table Of Contents
All user-adjustable parts are external and easily accessible. Never open the amplifier: you could run the risk of serious electric shocks. In the event of breakdown, contact the nearest GENERALMUSIC/LEM Assistance Centre ✔ ✔ ✔ ✔ ✔ Conservation of documents and packing. -
Page 4: Introduction
Introduction Introduction Congratulations for having chosen SWING 14P! TAPE TAPE MONO AUX INPUTS AUX SENDS LINE LINE LINE LINE LINE LINE OUTPUT OUTPUTS MIC/LINE MIC/LINE MIC/LINE LEFT LEFT (MONO) RIGHT RIGHT MONITOR OUT 11/12 13/14 TAPE IN LINE LINE LINE INSERT INSERT INSERT... -
Page 5: Mono Input Channel
MONO input channel MONO input channel MIC INPUT LINE LINE MIC/LINE Balanced XLR connector: this input is for use with microphones, but can also accept a wide range of balanced or unbalanced low impedance signals. Do not connect keyboards, recorders or other equipment with a line signal, as the signal level would be too high and probably distorted. - Page 6 MONO input channel MONITOR LINE LINE MIC/LINE Control for the MONITOR send level. The MONITOR send is PRE-FADER: this means than the signal sent to the MONITOR is taken before the control of the channel FADER, allowing a completely independent mix for the monitoring respect to the main mix.
-
Page 7: Stereo Input Channel
STEREO input channel STEREO input channel STEREO INPUT LEFT (MONO) Balanced JACK connectors: receive the STEREO LINE input signal on the channel (0dB). Inserting a single JACK connector on the LEFT socket this channel can be RIGHT used as a MONO channel. +4dB -10dB LEVEL... -
Page 8: Master Section
MASTER section MASTER section TAPE TAPE MONO AUX INPUTS AUX SENDS OUTPUT OUTPUTS LEFT LEFT (MONO) RIGHT RIGHT MONITOR OUT 11/12 13/14 TAPE IN LEVEL AMP MODE FOOTSWITCH MIX L&R L+R / MONITOR SOLO PHONES AUX SENDS 1&2 Unbalanced JACK connectors: these connectors feed out the sum of the signals arriving from the relative AUX sends of the input channels. -
Page 9: Dsp Footswitch
MASTER section TAPE IN SOLO Button for PRE-LISTENING of the TAPE INPUT: allows the TAPE IN signal to be selected for the listening thru the HEADPHONES outputs and the visualization on the LED BARGRAPHS. According to the position of the SOLO MODE button the listening and the visualization can be PRE or POST-FADER. MONITOR OUTPUT Unbalanced JACK connector: this connector feeds out the sum of the signals arriving from the relative MONITOR sends of the input channels. - Page 10 MASTER section MIX L&R Fader for control of the general volume: controls the level of the signal arriving from the input channels and sent to the main MIX L&R output, to the SUB-WOOFER TAPE OUT and to the built- 125 Hz in amplifier.
- Page 11 MASTER section STEREO 9-BAND STEREO 9 BAND GRAPHIC EQ GRAPHIC EQ Nine mini-slider for the GRAPHIC EQ control. The GRAPHIC EQ can be used to regulate the overall mixer frequency response, in order to control the tone of the main sound system and/or the recording.
- Page 12 MASTER section PHONES SOURCE Button for the selection of the signal sent to the HEADPHONES output when there are no SOLO switches pressed on the input channels. a) MIX L&R: select the MIX L&R signal. b) MIX B: select the MIX B signal. c) MONITOR: select the MONITOR signal.
-
Page 13: Dsp
The SWING 14P is fitted with a built-in DSP, including 128 high-quality REVERB and DELAY effects able to reproduce accurately different kinds of ambients and to VARIATIONS enrich not only the voice, but also any kind of instrument. 1 SHORTER The 128 PRESETS can be selected by means of two 16-position encoders. -
Page 14: Rear Panel
Rear panel Rear panel Mixer on/off switch. Power cord Main fuse holder In the event of breaking, always replace the fuse with same type and rating. +48V +48V Phantom power supply button: this button switches on the +48V power supply for all the MIC inputs (XLR-F connector) of the MONO input channels and allows condenser microphones to be used on them. -
Page 15: Connection Cables
Connection cables Connection cables Balanced XLR-M Unbalanced XLR-M Balanced JACK Unbalanced JACK RCA PIN JACK power connector INSERT connector... -
Page 16: Connection Example
Connection example Connection example LIVE SET MAIN P.A. from L&R POWER OUTPUTS STEREO VOCAL MIC COMPRESSOR CH 1, 2, 3 & 4 to/from INSERT 1&2 DAT RECORDER from TAPE OUT AMPLIFIED BRASS MONITOR CH 5 from MON OUT MINIDISC BASS PLAYER CH 6 CH 11/12... -
Page 17: Technical Specifications
Technical specifications Technical specifications SECTION LEVELS & DATA CONNECTORS MONO INPUT CHANNEL sensitivity from -10 to -60dB MIC input XLR-F balanced impedance 4 kOhms sensitivity from +10 to -40dB LINE input JACK balanced impedance 10 kOhms LO CUT 75 Hz, 18 db/oct. (CH 1-3) HIGH ±15dB, @ 12kHz SHELVING ±15dB from 100 Hz to 8kHz PEAKING (CH 1-3) -
Page 18: Schema A Blocchi
Block diagram Block diagram... - Page 19 FEDERAL COMMUNICATIONS COMMISSION NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 20 Sales Division: 47842 S.Giovanni in Marignano (RN) – Via delle Rose, 12 – tel. +39-0541-959511 – fax +39-0541-957404 Internet: http://www.lemaudio.com...
Need help?
Do you have a question about the SWING14P and is the answer not in the manual?
Questions and answers