Table of Contents
Advertisement
CONNECTIONS
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit may be
damaged
If this unit fails to tum on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR switch may not
be fully slide to either position If so, slide the switch to either position fully when this unit is in the standby mode
Select the right or left position according to the impedance of speakers in your system Be sure to move this switch only
when this unit is in the standby mode
(U S A model)
If you use
left position
light position
If you use one pair of main
If you use one pail of main
speakers, the impedance of
speakers, the impedance of
each speaker must be 4
Q
01
each speake! must be 8
Q
01
highel
higher
If you use two pairs of main
If you use two pails of main
Main
speakels, the impedance of
speakel s, the impedance of
speake!s
each speake! must be 8
Q
or
each speaker must be 16
Q
01
highel
highel
[Canada model only]
The impedance of each
speaker must be 8
Q
or
highel
Rea! speake! s The impedance of each
The impedance of each
speakel must be 6
Q
o!
speaker must be 8
Q
or
highel
higher
Centel
The impedance must be 6
Q
The impedance must be 8
Q
speakel
01
highel
or highel
After completing all connections, connect the AC power
cord to an AC power outlet Disconnect the AC power cord
if you will not use this unit for a long period of time
•
AC OUTLETS (SWITCHED)
(U S A model)
To AC outlet
SWITCHED
1R
USA and Canada models
2 OUTLETS
Australia model
I OUTLET
Use these outlets to connect the power cords from your
components to this unit The power to the AC OUTLET(S)
is controlled by this unit's STANDBY/ON (or POWER and
STANDBY) These outlets will supply power to any
connected component whenever this unit is turned on The
maximum power (total power consumption of components)
that can be connected to the AC OUTLET(S) is 100 W
CONNECTIONS
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit may be
damaged
If this unit fails to tum on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR switch may not
be fully slide to either position If so, slide the switch to either position fully when this unit is in the standby mode
Select the right or left position according to the impedance of speakers in your system Be sure to move this switch only
when this unit is in the standby mode
(U S A model)
If you use
left position
light position
If you use one pair of main
If you use one pail of main
speakers, the impedance of
speakers, the impedance of
each speaker must be 4
Q
01
each speake! must be 8
Q
01
highel
higher
If you use two pairs of main
If you use two pails of main
Main
speakels, the impedance of
speakel s, the impedance of
speake!s
each speake! must be 8
Q
or
each speaker must be 16
Q
01
highel
highel
[Canada model only]
The impedance of each
speaker must be 8
Q
or
highel
Rea! speake! s The impedance of each
The impedance of each
speakel must be 6
Q
o!
speaker must be 8
Q
or
highel
higher
Centel
The impedance must be 6
Q
The impedance must be 8
Q
speakel
01
highel
or highel
After completing all connections, connect the AC power
cord to an AC power outlet Disconnect the AC power cord
if you will not use this unit for a long period of time
•
AC OUTLETS (SWITCHED)
(U S A model)
To AC outlet
SWITCHED
1R
USA and Canada models
2 OUTLETS
Australia model
I OUTLET
Use these outlets to connect the power cords from your
components to this unit The power to the AC OUTLET(S)
is controlled by this unit's STANDBY/ON (or POWER and
STANDBY) These outlets will supply power to any
connected component whenever this unit is turned on The
maximum power (total power consumption of components)
that can be connected to the AC OUTLET(S) is 100 W
Advertisement
Table of Contents
