Advertisement
RECORD OF THERMOSTAT OPTIONS SELECTED
For your quick reference, below are the options selected by your installing dealer
to optimize your equipment settings and your personal home comfort preferences.
(Contractor to fill in value or check box. N/A = Not Applicable for your equipment or application.)
Thermostat Options Configuration Menu
On-Demand Dehumidification: Set RH ________% (Relative Humidity)
Continuous Fan Speed:
High
Program Days Per Week:
7 Program Days
Continuous Backlight:
On
Off
Energy Management Recovery:
On
Temperature Offset: _____ (0, 1, 2, 3, 4, 5°)
Temperature Display:
°F
°C (Fahrenheit/Celsius)
Beeper:
On
Off (Touch Key Input Confirmation)
Air Filter Maintenance: _____ Hours (System Runtime)
UV Lamp Maintenance: _____ Days
Humidifier Pad Maintenance: _____ Hours (Continuous Clock)
If you need help adjusting the programmed time or temperatures
in your thermostat, please call Homeowner Help Line at 800-284-2925
For All Other Service, Please Call:
Rheem Installing Dealer: ______________________________________________
Phone: ______________________________________________
Date Installed: ______________________________________________
Factory
Setting
OFF
Medium
Low (Fan-On Setting) Medium
0/Non-Programmable
7
On
Off
On
Hi (+)
Lo (-)
0°
°F
On
Off
Off
Off
MANUAL 37-6940A
0830
Advertisement
Table of Contents
Related Manuals for Rheem Comfort Control 2 System
Summary of Contents for Rheem Comfort Control 2 System
- Page 1 Humidifier Pad Maintenance: _____ Hours (Continuous Clock) If you need help adjusting the programmed time or temperatures in your thermostat, please call Homeowner Help Line at 800-284-2925 For All Other Service, Please Call: Rheem Installing Dealer: ______________________________________________ Phone: ______________________________________________ Date Installed: ______________________________________________ MANUAL 37-6940A...
- Page 2 These features ensure simple, reliable this Guide to put Menu options back as they were before the thermostat Reset. For your operation for you and installation for peak performance by your Rheem Dealer. convenience, Factory Settings are as shown.
- Page 3 Programmable Fan 5. Touch key to adjust the start TABLE OF CONTENTS time for period. The time will change in The indoor fan/blower can be selected 15 minute increments. to turn on and off with the cycle of the TOUCHSCREEN THERMOSTAT DISPLAY OVERVIEW.
-
Page 4: Touchscreen Thermostat Display Overview
3. Touch the Advance Day key until the 5. If you wish to copy this same program TOUCHSCREEN THERMOSTAT DISPLAY OVERVIEW Copy day you wish to copy to is flashing and into other days, touch the and repeat steps 3 and 4. the day you are copying is on. -
Page 5: Programming Your Thermostat
Run Schedule touch key to exit used in programming to PROGRAMMING YOUR THERMOSTAT any menu and begin operating the set time and in configuration menu to program. change selections (page 12). Set Time touch key used for setting “Outdoor Temperature” indicates the Programming Tip: Planning Your Program –... - Page 6 • Battery Location Select UV lamp maintenance re- minder. Scrolling message will show “UV LAMP MAINTENANCE”. Default 2 “AA” alkaline batteries are included is OFF. It can be changed to a setting in the thermostat to keep time during a from 25 to 1975 days in increments of power outage.
- Page 7 • Select temperature offset. Scrolling QUICK START GUIDE “TEMPERATURE message will show ADJUSTMENT”. Your thermostat was accurately calibrated at the fac- Set Current Time and Day tory, however this option allows you to change the display temperature to match your previous thermostat if •...
-
Page 8: Energy Saving Factory Pre-Program
• Select continuous FAN speed. Choose the System Mode (Cool, Off, Heat, Em, Auto) fault is Medium. It can be set to High, Medium or Low. In High, the fan will SYSTEM Touch the key to select: run at the highest speed when FAN key is selected to On. -
Page 9: Setting Up Your Thermostat Options
SETTING UP YOUR THERMOSTAT OPTIONS USING YOUR THERMOSTAT The Thermostat has comfort and performance options that can be selected and ad- System Operation justed. These options are in the Thermostat Options Configuration Menu. On the Home Screen Display, touch the Menu key to display additional key choices. - Page 10 Permanent Temperature Hold Non-Programmable Mode Maintenance Reminder Message The Permanent Temperature Hold feature If Program days per week is set for 0 A reminder will display in the scrolling bypasses the program and allows you days (Non-programmable) in the Ther- message area when it is time for ac- to adjust the temperature manually as mostat Options Configuration Menu, the...
Need help?
Do you have a question about the Comfort Control 2 System and is the answer not in the manual?
Questions and answers