Summary of Contents for Weslo Cadence G 7.0 WLTL39810.0
Page 1
USER'S MANUAL Model No. WLTL39810.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, please con- tact the store where you pur- chased this product.
If a decal is missing or illegible, see the front cover of this manual and request a free replacement decal. Apply the decal in the lo- cation shown. Note: The decals may not be shown at actual size. WESLO is a registered trademark of ICON IP, Inc.
9. To purchase a surge suppressor, see your local WESLO dealer or see your local 3. Use the treadmill only as described. electronics store. 4. Keep the treadmill indoors, away from mois- 13.
Page 4
19. The treadmill is capable of high speeds. 24. Inspect and properly tighten all parts of the Adjust the speed in small increments to avoid treadmill regularly. sudden jumps in speed. 25. Never drop or insert any object into any 20.
BEFORE YOU BEGIN Thank you for selecting the new WESLO CADENCE ing this manual, please see the front cover of this man- ® G 7.0 treadmill. The CADENCE G 7.0 treadmill offers a ual. To help us assist you, note the product model selection of features designed to make your workouts number and serial number before contacting us.
ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of the walking belt or the shipping carton.
Page 7
2. Attach the Handrails (69) to the Uprights (73) with four M10 x 45mm Screws (2). Start all four Screws, and then tighten each of them. 3. With the help of a second person, hold the con- sole assembly near the Uprights (73). Remove Console Assembly the tie from the Upright Wire (71).
Page 8
5. Attach the Latch Housing (72) to the left Upright (73) with two #10 x 1" Tek Screws (83); start both Screws, and then tighten each of them. Place the treadmill in the storage position (see HOW TO FOLD THE TREADMILL on page 15). 6.
OPERATION AND ADJUSTMENT THE PRE-LUBRICATED WALKING BELT dance with all local codes and ordinances. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets and may not be compatible Your treadmill features a walking belt coated with high- performance lubricant. IMPORTANT: Never apply sil- with AFCI-equipped outlets.
Page 10
CONSOLE DIAGRAM Pulse Sensor Clip FEATURES OF THE CONSOLE IMPORTANT: If there is a sheet of plastic on the face of the console, remove the plastic. To prevent damage to the walking platform, wear clean ath- The treadmill console offers a selection of features de- letic shoes while using the treadmill.
HOW TO TURN ON THE POWER HOW TO USE THE MANUAL MODE IMPORTANT: If the treadmill has been exposed to 1. Insert the key into the console. cold temperatures, allow it to warm to room tem- perature before turning on the power. If you do not See HOW TO TURN ON THE POWER at the left.
Page 12
4. Change the incline of the treadmill as desired. To reset the displays, press the Stop button, re- move the key, and then reinsert the key. To change the incline of the treadmill, press the 6. Measure your heart rate if desired. Incline increase and decrease buttons.
HOW TO USE A PRESET WORKOUT At the end of each segment, a series of tones will sound and the next segment of the profile will 1. Insert the key into the console. begin to flash. If a new speed and/or incline setting is programmed for the next segment, the speed See HOW TO TURN ON THE POWER on page 11.
Page 14
THE INFORMATION MODE into the console. However, when you remove the key, the displays will remain lit, although the buttons will not The console features an information mode that allows function. If the demo mode is turned on, a “d” will ap- you to turn on and turn off the demo mode and to se- pear in the left display while the information mode is lect miles or kilometers as the unit of measurement.
HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL HOW TO MOVE THE TREADMILL Before folding the treadmill, adjust the incline to Before moving the treadmill, fold it as described at the the lowest position. If you do not do this, you may left.
TROUBLESHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on SOLUTION: a.
Page 17
Remove the five indicated M4.2 x 19mm Washer Head Screws (9). Then, carefully remove the Motor Hood (56). Locate the Reed Switch (42) and the Magnet (44) on the left side of the Pulley (46). Turn the Pulley until the 1/8 in.
Page 18
PROBLEM: The walking belt is off-center or slips when walked on SOLUTION: a. If the walking belt has shifted to the left, first re- move the key and UNPLUG THE POWER CORD. Using the hex key, turn the left idler roller bolt clock- wise 1/2 of a turn.
EXERCISE GUIDELINES WARNING: Burning Fat—To burn fat effectively, you must exer- cise at a low intensity level for a sustained period of Before beginning any time. During the first few minutes of exercise, your exercise program, consult your physician. body uses carbohydrate calories for energy. Only after This is especially important for persons over the first few minutes of exercise does your body begin age 35 or persons with pre-existing health...
PART LIST Model No. WLTL39810.0 R0211A To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual. Key No. Qty. Description Key No. Qty. Description M10 x 65mm Patch Screw Walking Belt M10 x 45mm Screw Walking Platform M4.2 x 19mm Screw Right Foot Rail...
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro- vide the following information when contacting us: • the model number and serial number of the product (see the front cover of this manual) •...