Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
Operating temperature Rated AC 100-240V~50-60Hz 2.5A Dimension (W x H x D) 537 x 170 x 389mm 19.4±0.44 lbs (8.8±0.2kg) Weight Note: Designs and specifications are subject to change without prior notice ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
The lamp must be operated on the USHIO’s lamp driver. ♦ On/Off cycle: 2 hours on, 15 minutes off. ♦ Ambient temperature should be room temperature (about 25℃) ♦ Illuminance should be measured on the specific optical system. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 6
C to prevent a deterioration of cladding clad of the fluorocarbon resin. ♦ The lead wire insulation clad shouldn’t touch the reflector. ♦ Exchange the lamp that has already passed the life time immediately. ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
4. Front IR remote control sensor 12. Air filter cover 5. Elevation foot 13. AC power socket 6. Elevation button 14. Projection lens 7. Connection ports 15. Ceiling mount (3-M6) 8. Rear IR remote control sensor (15) ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Page 8
To confirm selected menu item. without physically moving the unit. 9. Power 6. Zoom/Focus Turn on or off the projector. Motorized zoom and focus adjust. 10. Menu/Exit Opens and Exits the on-screen menu. ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
No 10 Fan1 No 11 Back IR No 12 12 Pin Power control No 13 Keypad control(FPC) No 14 Fan4 No 15 R FPCB No 16 G FPCB No 17 B FPCB ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Page 10
Ballast Board Connector Description No 1 Power supply No 2 Lamp power supply No 3 Ignite signal connected to Mainboard ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Page 11
No 3 4 pin wire(power board-DC jack board) No 4 2 pin wire (power board-DC jack board) No 5 unused No 6 380V power supply No 7 thermostat No 8 AC Input ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Page 12
Level 3 : Board Level Repair or RTV Optical Engine (LCD Panel / lens ) Level 1: End user can replace by themselves Level 2: Service Center Level 3: RTV ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
BE EF 02 06 00 15 D8 4C 00 00 00 00 00 Overscan BE EF 02 06 00 C4 D9 4D 00 00 00 00 00 Black level BE EF 02 06 00 F7 D9 4E 00 00 00 00 00 ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Page 15
800 x 600 75 Hz 46.9 kHz 800 x 600 85 Hz 53.7 kHz 1024 x 768 50Hz 39.63 kHz 1024 x 768 60Hz 48.4 kHz 1280x768 60 Hz 47.8 kHz WXGA ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Page 16
60.0 kHz 1360 x 768 60 Hz 47.7 kHz 1440 x 900 60 Hz 55.9 kHz Compatible/Supportive timing Note: the Projector may need minor adjustment in the OSD to get optimized performance, ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
1. Connect USB cables on NB/PC and Pro8100. To get into Service mode: Press on the Menu button then press Power button. (The Top LED will flash quickly) 3. Open “Pro8100 Updater” file PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 19
4. Execute “Updater.exe” file on the PC. Click on the Browse button and browse the “xxxxx.brec” file. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 20
Press Update button to upload the F/W into Pro8100. 7. After Firmware upgrades completed. Press Exit button to exit the updater. Remove USB cable and power cable. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
<NOTE>: This software requires Microsoft .NET Framework 2.0 via Internet. Please make sure your PC is connected to the Internet. 1. Install WriterSpiRomForL0046 software (1) Double-click setup.exe icon in the Soft directory PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 22
(4) After finish downloading, if you see following dialog, click Yes to reboot your PC. If not require to reboot, you will see Welcome to the WriteSpiRom For L0046 Setup Wizard. Please go to (6). PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 23
(5) After rebooting, following dialog will be automatically appeared. If not appeared, please double-click setup.exe icon in the \Soft directory. (6) Click Next. (7) Select Installation Folder by Browse and Click Next. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 24
(8) Click Next. (9) Click Close. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 25
(10) After installation complete, short-cut icon will be appeared on the desk-top. 2. Install LPT Driver If you use ROM programmer tool, LPT Driver installation is not required. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 26
(2) Click the Performance and Maintenance icon. (3) Click the System icon PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 27
(4) Select Hardware menu and click Add Hardware Wizard. (5) Click Next to continue. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 28
(6) Select Yes, I have already connected the hardware and click Next. (8) Select Install the hardware that I manually select from a list (Advanced) and click Next to continue. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 29
(9) Select Show All Devices and click Next to continue. (10) Select Have Disk ..PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 30
(11) Browse to the jpcEvaDev.inf file in the \Driver \ LPT directory and click OK. (12) Click Next to continue. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 31
(13) Click Next to continue. (14) Click Finish in the Completing the Add Hardware Wizard dialog. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 32
(1) Connect MiniFX2 Board to the USB Port. (2) Select Not, not this time And click Next to continue (3) Select Install from a list or specific location[Advanced] And click Next to continue. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 33
(4) Browse to the ezusb.inf file in the ¥Driver¥MiniFX2 directory and click Next to continue. (5)Click Continue Anyway. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 34
Turn on the projector, Press the direction keypad following the actions below: Up twice, down twice, left once, right once, left once, right once(▲▲▼▼◄►◄►),press the MENU button, Enter the engineer mode, Setting PCS[1]. Double-click WriterSpiRomForL0046. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 35
Select “TEST”. Click “EXEC” button. Select “MAIN”. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 36
Click “SEARCH” button and select file. Press EXEC button to update the Jepico F/W PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 37
How to reset the lamp hours of Pro8100 Press “Menu” button to open the Main menu Press “Right” button to open this menu Select “CONFIG” ,Press “ ”(Enter) button. Select “TIMERS” ,Press “ ”(Enter) button. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 38
Select “LAMP TIMER RESET” ,Press “ ”(Enter) button. Select “yes”,Press Menu button. Then the lamp hours would be reset to zero. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
MENU button. 3. Move the color bar to “Lamp reset”. 4. Press right button. 5. Then the lamp hours would be reset to zero. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 40
Final solution for “Lock up when first startup the projector” 1.If the projector lock up when first startup ,please add four SMD spring(FOXCONN PN:J2349-0040-00) in the main board. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 41
J2349-0040-00 (Model NO:S8-90RCG) Specification for approval PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 42
NOTE: 1. Material:Be-Cu 2.Thickness:0.10mm 3.Electroplate:Au 4.Tolerance:+_0.3mm 5.Package:1000pcs/Reel 6.Height of Application:5.6~8.7mm 7.Conform:“ROHS” PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Machine Disassembly and Replacement Tools Item Photo Long Nose Nipper Hex Sleeves 5mm Screw Bit(+):107 Screw Bit(+):101 Screw Bit(+):102 Anti-static wrist strap Anti-static wrist gloves PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 44
When you replace the projector lamp, never touch the new lamp with your bare hands. The invisible residue left by the oil on your hands may shorten the lamp life. Use lint-free gloves or finger cots are recommended. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 45
1. Push the changeable top cover in accordance with the direction of the identification of arrow point, remove the changeable top cover 1. Appear this PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 46
Turn the projector over by pulling the latches upwardRemove the screws J1635-3680-00*10. 1.Remove the screws J1635-A973-00*2 on the back cover Remove EMI Metal Plate 1.Remove the top cover. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 47
2. Remove the EMI real metal . Note: Before removed the EMI real metal,you shoule be disconnected wires of mainboard module. 1.Show you what the connector should be. 2.Remove all the wires PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Remove the mainboard module. NOTE:2 wires still have connection under mainboard. Disconnect these two wires before remove mainboard Remove FAN Housing(fan5,fan6) 1. Remove the screws J1635-B853-00*2 and J1635-A641-00*2. Remove the sheet link PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 49
1. Remove the screws J1635-A641-00*3 and then the left fan housing. 2. 1.Remove the screws J1635-A641-00*3 and then the righ fan housing. Remove FAN2 Remove the screws J1635-C093-00*2 and then remove fan2 PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 50
Loosen the screws J1635-A641-00*2 to remove ballast hoursing Remove Optical Engine Remove the screws J1635-A641-00*2 and then Remove the thermal sensor on the Optical engine. Remove the screws J1635-D363-00*6 PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 51
Loosen the screws J1635-A641-00*1 to remove the Optical engine. Remove FAN1 Loosen the screws J1635-A641-00*3 to remove fan cover as shown. Loosen the screws J1635-C093-00*3 to remove the FAN1. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 52
Remove Power board module .Loosen screws J1635-A641-00*4 and remove the power board module from bottom cover Remove ballast .Loosen screws J1635-A641-00*4 and remove the ballast cover. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 53
Remove the lamp cover. Loosen the two screws of lamp module. Pull out the old lamp module by lamp handle. Mount the new lamp. Replace the lamp cover. Reset the lamp timer. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Blinking in Red Lamp error. Orange Blinking in Orange Fan error. It is time to clean the Air Green Blinking in Orange filter. Green Blinking in Red Projector overcooled (3) Confirm cable connection well. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 58
Replace keypad Check LED and keypad and FPC Replace fan Check Note: (check one by one) Check 12 pin Check Power output Fuse Replace Check Mainboard Mainboard Replace Replace power mainboard board PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 59
Refer to LED Check LED indicator and follow indication indicative actions Replace Check Lamp life Lamp Module Replace Check Power board Power board 380V output Replace Check Ballast Ballast Replace Check Mainboard Mainboard PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Check Check Source Source Source Source Replace Replace Check Check Cable Cable Cable Cable Replace Replace Optical Check monitor Check out signal Mainboard Optical Engine Engine Replace Check Optical Engine Optical Engine PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 61
Input signal reset OSD Adjust Replace Check Check input cable Input signal Mainboard and signal setting Mainboard Replace Replace Check Check Mainboard Mainboard Optical Engine Optical Engine Replace Check Optical Engine Optical Engine PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 62
Button Failure Failure Replace Replace Check Check Battery Level Battery Keypad and FPC Keypad and FPC Replace Replace Check Check Remote Control Remote Control Mainboard Mainboard Replace Check Replace Check Mainboard Mainboard PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 63
Connect projector USB to PC. Press remote controller page up/down to scroll presentation file up and down (ex Microsoft office series) I/O port HDMI Test Equipment Standard Pattern generator or DVD player Signal format 1080i/p, 720p, PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 64
Press “Zoom” button should be free from getting stuck. Focus ring Mechanical motion (Up & Down) should be free from getting stuck when pressing the button. Press “focus” button should free from seizing. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 65
G, and B single level respectively are acceptable. 16 gray level --16 level of gray level color should be distinguishable --When Gamma selected to “RGB” Not distinguishable of 2 brightest levels /2 darkest levels are acceptable. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 66
480i Criteria No apparent color deviation on the projected image Video I/O port Video Test Equipment Standard Pattern generator (Ex. Quantum data)&DVD player Criteria No apparent color deviation on the projected image PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 67
2. Cover rear sensor and operate remote controller to test front sensor (6) Brightness measurements Test items Brightness measurements Test Equipment Chroma automatic system (The alternative is CL-200) Test method Measure 9 points Criteria Marketing spec 20% off PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 68
2. Plug the power cord to socket Test criteria GND 30A 3sec 100mΩ DCW 2506V 1sec 250uA Single Step OFF (8) Cosmetic standard for repaired projector Follow cosmetic standard for repair center. PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
Page 69
MENU button, Enter the engineer mode. 3.Choose the "ADC Calibration", press right key to conduct ADC calibration . do not go to next step until the image appears again, or it should be re-calibrated . PRO8100-1 ViewSonic Corporation Confidential - Do Not Copy...
OUTPUT 3A MAX R335 R335 FOR FAN_LAMP_TEMP_SENSOR POWER 7.87K/1% 7.87K/1% 17.5mA 5V_ADC 3VAA TP28 TP28 AIC1117-3.3 AIC1117-3.3 0.1uF 0.1uF 10uF/16V 10uF/16V 0.1uF 0.1uF 10uF/10V 10uF/10V ViewSonic Corporation Model POWER_SYSTEM Title Date Rev: ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Page 72
R130 HI : FULL DC CHANNEL OUT NC/4K7 NC/4K7 5V_ST : STAND-BY MODE R124 R124 NC/1K NC/1K POWER_HC PWR_STBYON 1,11 POWER_HC 74LVC1G125 74LVC1G125 R133 R133 ViewSonic Corporation Model POWERPIC Title Date Rev: ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Page 73
TP610 C309 C309 C308 C308 R287 R287 R285 R285 NC/2.2K NC/2.2K 2.2K 2.2K NC/22pF NC/22pF 22pF 22pF D-SUB D-SUB VVCC VVCC VVCC VVCC VVCC VVCC ViewSonic Corporation Model DSUB_INPUT Title Date Rev: ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Make sure the lens is cool before cleaning. Do not use detergents or chemicals other than those noted above. Do not use benzene or thinners. Do not use chemical sprays. Use a soft cloth or lens paper only. ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...
Page 114
Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) ViewSonic Corporation PRO8100-1 Confidential - Do Not Copy...