AMP1 AMP1 AMP2 LOCK LEFT RIGHT MUTE GAIN EQ LPF HPF PHASE KOMP kicker AMP2 MEM-1 MEM-2 MEM-3 MEM-4 LOCK - Indicates the amplifier controls are locked out and not usable. LEFT - Indicates an action or adjustment of the left channel.
Page 4
SX .4 Series Amplifiers BLAST Port In BLAST Port Out When selecting a location to mount your Kicker amplifier be sure it is structurally sound and that there are no items behind the area that could be damaged by the screws. Check for wiring, brake lines, fuel lines, gas tanks, etc.
Hi-Lo level signal power connection to the battery. Adding an additional ground adapter. See your Kicker dealer for more details on this. wire between the car battery’s negative post and the car chas- sis of this same gauge (or larger) is also recommended.
Page 6
BATTERY HOME These are just a few of the many ways you can use your SX.4 series Kicker amplifier. These system diagrams are designed to give you a basic understanding of the most com- mon uses for this amplifier. For more complex systems please visit your local authorized Kicker dealer.
BLAST output jack of the first amp to the BLAST input jack of the next amplifier. On a KICKER SX.4 series amplifier you can control AMP 1, AMP 2 or both of them using the Remote Bass Level Controller.
This information scrolls through the display one after the other and then repeats. - Hey, we needed a brand plug for us since this KICKER amp is sooooo cool! - Displays the current voltage at the XX.X Volts amplifier’s + 12 volt battery input terminal.
Page 9
HOME Amp Name - Here you can assign a unique name to your KICKER SX amplifier. This name will replace the model 7c.) PINK NOISE is a built in pink noise generator name in the DEFAULT screen. If you change your mind and...
Page 10
10.) Mem Name - Here you can change the names of the REMOTE CTL memory locations. The factory defaults are controlled by the Remote Bass Level Controller. The options BOTH AMPS Memory-1 Use the Memory-2 Memory-3 select which option you want to use HOME and press the Memory-4...
Page 11
15.) 16.) Display - Several options to allow customizing Lock Code the amplifier’s VFD display. default is code with up to 10 characters. 15a.) BRIGHTNESS - Adjust the intensity level of the ISIS VFD display. Five selectable levels. MINIMUM - dimmest setting. cursor left or right to select which character to change.
Page 12
AMP1 AMP 2 amplifier you are currently adjusting. 20325 Hz The KICKER SX amplifier monitors and prevents any low pass crossover point from being any closer than 1/3 octave from keys to DOWN the high pass crossover point. If you cannot set the low pass...
Page 13
1/12th octave frequency from 10 Hz to 16 kHz. AMP1 amplifier you are currently adjusting. 10 Hz 16132 Hz The KICKER SX amplifier monitors and prevents any high Use the DOWN keys to pass crossover point from being any closer than 1/3 octave select your frequency.
Page 14
MENU - Here you can mute each amplifiers channel(s) If done adjusting the muting, press Mute output for setup or testing purposes. There are two MUTE MAIN menu menus, one for AMP 1 and one for AMP 2. This allows each amplifier to have its own individual muting function.
Page 15
You will need to call KICKER directly at (405) 624-8583 to handle this situation. You will need your amplifier’s serial number AND your receipt as the guys and gals answering the and return you to the screen.
VFD display flashes LOCK LEFT RIGHT MUTE Each preset stores GAIN EQ LPF HPF PHASE KOMP STORED kicker all the values for The indicator which matches the preset each of the MEM-1 MEM-2 MEM-3 MEM-4 you used will illuminate. following amplifier...
Other S S ymptoms: Amp is very hot, no output. There are two LEDs on the end panel of your KICKER SX series amplifier, one green and one red. The green LED indi- verify. Check for proper impedance at speaker cates the amplifier is turned on.
Page 18
@ 14.4V, 4Ω Mono, 1% THD Length With EndKaps setting is really geared for bass and midbass Fusing Recommended Power & Ground Wire Performance Model SX700.4 SX900.4 82 x 4 107 x 4 163 x 4 213 x 4 325 x 2...
“B B S S t t o o c c k k ” it is warranted for 9 9 0 0 D D A A Y Y S S from date of original purchase with receipt. If labeled “B B S S t t o o c c k k ” and purchased from an Authorized KICKER Dealer, it is warranted for O O N N E E ( ( 1 1 ) ) Y Y E E A A R R from date of purchase with receipt.
Page 20
Notes Pizza Delivery Chic’s Numbers Hook Ups SX .4 Series Amplifiers SX .4 Series Amplifiers...
Need help?
Do you have a question about the SX700.4 and is the answer not in the manual?
Questions and answers