Advertisement
1. Place a sheet mask on your face or evenly spread your regular milky lotion over your face.
Wipe the milky lotion off your hands.
2. Press the power switch. (Fig. 12)
The "LEVEL" indicator lamp will light, and the "REFRESH" mode indicator lamp will
flash. If another mode indicator lamp flashes, press the mode selector button to
switch the mode.
If the power switch is pressed after the end of the "MOISTURIZE" mode, the
"REFRESH" mode is set automatically.
3. Select the potential power level ("HIGH" or "LOW") with the "LEVEL" selector button.
Select the potential power level ("HIGH" or "LOW") with the "LEVEL" selector button
according to your skin condition.
Every time the "LEVEL" selector button is pressed, the potential power level is
switched between "HIGH" and "LOW". The vibration power does not change.
The previous potential power level ("HIGH" or "LOW") is stored by the memory function.
Use at the "LOW" level is recommended for people who use this device for the first
time and who feel something unusual.
4. Hold the main body by the side plate. (Fig. 10)
Make sure to hold the body with your hand touching either of the right and left side
plates.
5. Apply the head directly to your skin and move it slowly.
The mode indicator lamp will light, and the device will start to vibrate.
Use this device within 5 minutes.
After 5 minutes have elapsed, the device will stop automatically.
CAUTION
The device will not vibrate unless you apply the head to your skin while touching
the side plate. (Skin sensing function)
If the head is not vibrating, the device is not working.
Power will be automatically turned off if device is unused for 30 seconds.
(Auto-off function)
Apply head onto skin and slowly head from center to the outside of your face.
Do not keep the head on the same part of your skin, but move it
around. (Cause of skin trouble or poor health condition)
Do not use this device on the same part of your skin for more than 10 seconds.
If you feel slight current stimulation (a tingling sensation) during use, press the
"LEVEL" selector button to set the "LOW" level.
6. An automatic stop is made when 5 minutes have elapsed. (Auto-off function)
You will know the automatic stop with the ending sound.
7. Wipe the skin lotion off the head and main body with tissue, etc.
How to use with AC
Never use this product in places splashed with water or in damp
places, such as in a bathroom.
(Cause of an electric shock or short circuit)
1. Connect the charger to the main body and outlet.
Use according to "How to use."
The charge lamp stays out during operation.
2. Make sure to pull out the charger from the outlet and the main body.
Care for the main body
Wipe the toner or milky lotion off the main body and ring with tissue, etc.
When dirt is difficult to remove, wipe it with a cloth moistened with water and firmly
squeezed.
Do not wash the main body with water. And, do not soak in water
or splash water on it. (Cause of a failure)
Make sure to turn OFF the switch.
(Improperly turning on the switch may cause irritation or a malfunction.)
Do not use alcohol, benzine, or thinner.
CAUTION
(Cause of deformation or discoloration)
How to preserve
Preserve in an area with little humidity and dust.
Do not leave this product in places splashed with water or in damp
places, such as in a bathroom. (Cause of a short circuit or failure)
Do not leave this product in areas exposed to direct sunlight
CAUTION
(inside of a vehicle, etc.) or near heaters.
(Cause of deformation or discoloration)
Specifications
Charger
100 - 240V AC, common to 50-60Hz
Power
(KH-182B)
supply
Main body
Batteries [Nickel-hydrogen battery (1.2V DC, 500mAh
Charging time
5 hours as standard
Rated time
20 minutes at the maximum (basic mode: 15 minutes)
Accessories
Rings (two), stand
Disposal of the product
Do not disassemble except when disposing of the product.
This product includes recyclable parts.
For disposal of the parts, observe your local laws and regulations etc.
How to remove the nickel-hydrogen batteries
1. Keep pressing the power switch continuously while it is "ON" for 10 seconds or more to
make the device vibrate and leave it until the vibration stops.
2. Remove the two screws on the reverse side of the main body. (Fig. 13)
3. Insert a flat-blade screwdriver or the like in the gap between the main body cases (front)
and (rear), and remove the main body case (rear). (Fig. 14)
Flat-blade screwdriver
Main body case (rear)
4. Cut the lead wires connected to the terminals of the nickel-hydrogen batteries near the
terminals, and take out the batteries from the battery holder. (Fig. 15)
Main body case (front)
Lead wires
Do not allow the (+) and (-) terminals of the removed nickel-hydrogen
batteries to make contact. (Cause of a short circuit or burns)
)]
Screws
Nickel-hydrogen batteries
Battery holder
Advertisement
