Advertisement
2. Press the power switch. (Fig. 9)
The "LEVEL" indicator lamp will light, and the "MICRO-PAT" mode indicator lamp will
flash. If another mode indicator lamp flashes, press the mode selector button to
switch the mode.
If the power switch is pressed after the end of the "CLEANSING" mode, the
"MICRO-PAT" mode is set automatically.
3. Select the potential power level ("HIGH" or "LOW") with the "LEVEL" selector button.
Select the potential power level ("HIGH" or "LOW") with the "LEVEL" selector button
according to your skin condition.
Every time the "LEVEL" selector button is pressed, the potential power level is
switched between "HIGH" and "LOW". The vibration power does not change.
The previous potential power level ("HIGH" or "LOW") is stored by the memory function.
Use at the "LOW" level is recommended for people who use this device for the first
time and who feel something unusual.
4. Hold the main body by the side plate. (Fig. 10)
Make sure to hold the body with your hand touching either of the right and left side
plates.
5. Apply the head directly to your skin and move it slowly.
The mode indicator lamp will light, and the device will start to vibrate.
Use this device within 5 minutes.
After 5 minutes have elapsed, the device will stop automatically.
CAUTION
The device will not vibrate unless you apply the head to your skin while touching
the side plate. (Skin sensing function)
If the head is not vibrating, the device is not working.
Power will be automatically turned off if device is unused for 30 seconds.
(Auto-off function)
Apply head onto skin and slowly head from center to the outside of your face.
Do not keep the head on the same part of your skin, but move it
around. (Cause of skin trouble or poor health condition)
Do not use this device on the same part of your skin for more than 10 seconds.
If you feel slight current stimulation (a tingling sensation) during use, press the
"LEVEL" selector button to set the "LOW" level.
6. An automatic stop is made when 5 minutes have elapsed. (Auto-off function)
You will know the automatic stop with the ending sound.
7. Wipe the toner off the head and main body with tissue, etc.
Step 3
"MOISTURIZE"
This mode is to give moisturizing care by making the moisturizing ingredients of the toner
permeate your skin.
1. Attach a new cotton puff to the main body, and fix it with the ring.
For attaching a cotton puff, see "Preparation for use."
2. Saturate the cotton puff with your regular toner.
Do not use a milky lotion or gel. Saturate the cotton puff with the toner until it
seeps through the cotton puff to the rear side.
3. Press the power switch. (Fig. 11)
The "LEVEL" indicator lamp will light, and the "MOISTURIZE" mode indicator lamp
will flash. If another mode indicator lamp flashes, press the mode selector button
to switch the mode.
If the power switch is pressed after the end of the "MICRO-PAT" mode, the
"MOISTURIZE" mode is set automatically.
4. Select the potential power level ("HIGH" or "LOW") with the "LEVEL" selector button.
Select the potential power level ("HIGH" or "LOW") with the "LEVEL" selector button
according to your skin condition.
Every time the "LEVEL" selector button is pressed, the potential power level is
switched between "HIGH" and "LOW". The vibration power does not change.
The previous potential power level ("HIGH" or "LOW") is stored by the memory function.
Use at the "LOW" level is recommended for people who use this device for the first
time and who feel something unusual.
5. Hold the main body by the side plate. (Fig. 7)
Make sure to hold the body with your hand touching either of the right and left side
plates.
6. Apply the cotton puff to your skin and move the device slowly. (Fig. 8)
The mode indicator lamp will light, and the device will start to vibrate.
Use this device within 5 minutes.
After 5 minutes have elapsed, the device will stop automatically.
CAUTION
The device will not vibrate unless you apply the cotton puff to your skin while
touching the side plate. (Skin sensing function)
If the head is not vibrating, the device is not working.
Power will be automatically turned off if device is unused for 30 seconds.
(Auto-off function)
Apply head onto skin and slowly head from center to the outside of your face.
Do not keep the cotton puff on the same part of your skin, but
move it around. (Cause of skin trouble or poor health condition)
If the moisture in the cotton puff becomes insufficient or if it is hard to slide, add more
toner.
Do not use this device on the same part of your skin for more than 10 seconds.
If you feel slight current stimulation (a tingling sensation) during use, press the
"LEVEL" selector button to set the "LOW" level.
If you still feel a "tingling sensation," add more toner.
7. An automatic stop is made when 5 minutes have elapsed. (Auto-off function)
You will know the automatic stop with the ending sound.
8. Remove the ring and the cotton puff.
Wipe off the surface of the head with tissue, etc.
Do not use the cotton puff again once it is used because its reuse will cause
skin trouble.
Step 4
"REFRESH"
(It is recommended that you use this step once every one or two weeks.)
This mode is to condition your skin by fine vibrations and gentle electrode switching.
Advertisement
