Sony FD Trinitron KV-32FQ70B Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. TV
  5. FD Trinitron KV-32FQ70B
  6. Service manual

Sony FD Trinitron KV-32FQ70B Service Manual

Trinitron
Hide thumbs Also See for FD Trinitron KV-32FQ70B:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual

SERVICE MANUAL

MODEL
KV-32FQ70B
KV-32FQ70E
COMMANDER
DEST
CHASSIS NO.
RM-938
FR
SCC-Q83N-A
RM-938
ESP
SCC-Q81Q-A
MODEL
KV-32FQ70K
KV-32FQ70U
KV-32FQ70
- 1 -
AE-6B
CHASSIS
COMMANDER
DEST
CHASSIS NO.
RM-938
OIRT
SCC-Q82J-A
RM-938
UK
SCC-Q84N-A
RM-938

Advertisement

Table of Contents
loading

Related Manuals for Sony FD Trinitron KV-32FQ70B

Summary of Contents for Sony FD Trinitron KV-32FQ70B

  • Page 1: Service Manual

    SERVICE MANUAL AE-6B CHASSIS MODEL MODEL COMMANDER DEST CHASSIS NO. COMMANDER DEST CHASSIS NO. KV-32FQ70B KV-32FQ70K RM-938 SCC-Q83N-A RM-938 OIRT SCC-Q82J-A KV-32FQ70E KV-32FQ70U RM-938 SCC-Q81Q-A RM-938 SCC-Q84N-A KV-32FQ70 RM-938 - 1 -...

  • Page 2: Table Of Contents

    PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN LE NUMÈRO DE PIÈCE EST INDIQUÈ...
  • Page 3 Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
  • Page 4 l l a . s l . s l . s l . s l . s l e i l . s l t c i n i l i n i - 4 -...
  • Page 5 y t i WARNING (UK Models only) The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 5 AMP rating. Should the fuse need to be How to replace the fuse. Open the fuse compartment with replaced, use a 5 AMP FUSE approved by ASTA to BS 1362, ie one a screwdriver blade and replace that carries the...
  • Page 6 21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left) Output impedence : Less than 1kohm*...

  • Page 7: Self Diagnostic Software

    AE-6B SELF DIAGNOSTIC SOFTWARE The identification of errors within the AE-6B chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.

  • Page 8: Switching On The Tv And Automatically Tuning

    Switching On the TV and Automatically Tuning The Auto Tuning menu appears on the screen. Press the Do you want to start OK button to select Yes. automatic tuning? The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to: 1) choose the language of the menu screen, 2) adjust the picture slant, 3) search and store all available channels (TV Broadcast) and 4) change the order in which the channels (TV Broadcast) appear on the screen.

  • Page 9: Introducing And Using The Menu System

    • Brightness, Colour and Sharpness can only be altered if “Personal” mode is selected. The “BBE High Definition Sound system” is manufactured by Sony Corporation under license from BBE Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866. The word •Hue is only available for NTSC colour signal (e.g: USA video tapes).

  • Page 10: Teletext

    Teletext Level 1 Level 2 Level 3 / Function MANUAL PROGRAMME PRESET The “Manual Programme Preset” option in the Picture Adjustment Teletext is an information service transmitted by most TV stations. The index page of the Picture Mode Personal “Set Up” menu allows you to: Contrast teletext service (usually page 100) gives you information on how to use the service.

  • Page 11: Remote Control Configuration

    Front Terminals Accessories supplied: In it’s default condition this remote control will operate the basic functions of this Sony TV, Sony DVDs and most Sony VCRs. To control VCRs and DVDs of other manufacturers (and some Sony 1 Remote Control (RM-938) S Video input –...

  • Page 12: Troubleshooting

    • Using the menu system, select the “Picture Adjustment” programmes. menu and select “Reset” to return to factory settings (see The standby indicator • Contact your nearest Sony service centre. page 9). the TV flashes. • This is not a malfunction. Press the number buttons on the...

  • Page 13: Disassembly

    SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal 2-2. Speaker Box Removal => => => => Screws Remove the rear cover fixing screws indicated and pull the To remove the speaker box assembly remove the two screws rear cover backwards away from the set. circled and unplug the speaker lead from connector CN2500 on the ‘A’...

  • Page 14: Service Position

    2-4. Service Position 2-5. G Board Removal Clips To remove the G Board release the clips circled and ease the To place the chassis in the service position, remove the board gently away from the support bracket. speaker assembly box (see 2-2.) and insert the main bracket firmly into the T-slot located on the left corner of the beznet as indicated (see inset).

  • Page 15: M2 Board Removal

    2-8. M2 Board Removal 2-9. Service Connector for M2 Board To A Board From M2 Board Extender Board Assembly A-1642-293-A If the M2 Board needs to be removed for testing when the chassis is placed in its service position, it would be necessary To remove the M2 Board gently release the two clips with a to use an extender board and extension cable as indicated screwdriver and remove the board from its socket vertically.

  • Page 16: Picture Tube Removal

    2-11. Picture Tube Removal WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.

  • Page 17: Bottom Plates

    For safety reasons, on no account should the plates be removed REMOVAL AND REPLACEMENT OF THE MAIN BRACKET and not refitted after servicing. BOTTOM PLATES. (1) REMOVING THE PLATES (2) REFITTING THE PLATES In the event of servicing being required to the solder side of the printed wiring boards, the Because the plates differ in size it is important that the correct plates are refitted in their original bottom plates fitted to the main chassis bracket require to be removed.

  • Page 18: Set-Up Adjustments

    SECTION 3 SET-UP ADJUSTMENTS • When complete readjustment is necessary or a new picture tube Carry out the adjustments in the following order : is installed, carry out the following adjustments. 3-1. Beam Landing. • Unless there are specific instructions to the contrary, carry out 3-2.

  • Page 19: Convergence

    Fig.3-4 Align both Purity Purity magnets Purity control magnets magnets to the vertical position Align pips on each magnet 3-2. Convergence (1) Screen centre convergence [Static convergence] Input a dot pattern signal from the pattern generator. Normalize the picture setting. [Moving vertically], adjust the V.STAT magnet so that the vertical red, green and blue dots coincide at the centre of the screen.
  • Page 20 Correction for HMC [Horizontal mis-convergence] and VMC HTIL correction can be performed by adding a THL correction [Vertical mis-convergence] by using the BMC [Hexapole] assembly to the Deflection yoke. magnet. a). HMC correction by BMC [Hexapole] magnet and movement of the electron beam.

  • Page 21: Focus Adjustment

    Layout of each control 3-3. Focus Adjustment Receive a television broadcast signal. Normalize the picture setting. Purity magnet Adjust the focus control located on the flyback transformer to BMC (Hexaploe) magnet obtain the best focus at the centre of the screen. V STAT convergence magnet Bring only the centre area of the screen into focus, the magenta- Y-splitting axis correction magnet...

  • Page 22: Section 4 Circuit Adjustments

    SECTION 4 CIRCUIT ADJUSTMENTS 4-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied remote Commander RM-938. Programming the Remote Commander for Operation in Service Mode Press the VCR/TV/DVD button until the TV LED lights. Press and hold the yellow button for approx.
  • Page 23 Sub Brightness Adjustment Input a Monoscope pattern. Program the Remote Commander for operation in Service Mode. [ See Page 22 ]. Press ‘VIDEO’ ‘VIDEO’ 13 on the Remote Commander. Adjust the ‘Sub-Brightness’ data so that there is barely a difference between the 0 IRE and 10 IRE signal levels. Sub Contrast Adjustment Input a video signal that contains a small 100% white area on a black background.

  • Page 24: Test Mode

    Deflection System Adjustment 4-2. TEST MODE 2: Program the Remote Commander for operation in Service Mode. Test Mode 2 is available by rogramming the Remote Commander for [ See Page 22 ] and enter into the ‘Geometry’ service menu. operation in Service Mode [ As shown on Page 22 ] then pressing the Select and adjust each item in order to obtain the optimum image.

  • Page 25: Block Diagrams

    5-1. BLOCK DIAGRAMS (1) CN7444 POWER CN7442 QP (-) QP (+) CN6400 CN6401 VM AMPLIFIER VM AMPLIFIER QP (-) BUFFER BUFFER OUTPUT TO G BOARD TO A BOARD (1/2) QP (-) Q7402 Q7403 Q7406 CN6001 QP (+) CN7000 VM AMPLIFIER VM AMPLIFIER S6400 BUFFER...

  • Page 26: Block Diagrams

    5-1. BLOCK DIAGRAMS (2) TO A BOARD 6dB AMPLIFIER SHEET 1 FOR THE SELECTABLE OUTPUT CVBS PART OF (3RD SCART) OVERVOLTAGE Q3202 PROTECTION Q5816 IC7300 CN7301 VIDEO OUT (RED) CN6200 6dB AMPLIFIER FOR THE TO G BOARD J7376 SELECTABLE V OUT 3 CN6008 OUTPUT CVBS (3RD SCART)

  • Page 27: Block Diagrams

    5-1. BLOCK DIAGRAMS (3) COMPARATOR IC8103 CN8810 V STAT TO A BOARD (1/2) DY ASSY CN5002 H CENTRE CN8611 M PIN CONT V- DY+ V- DY- V DY CN8620 Q8201, MP PARA H DY 8202,8118 H- DY- H LIN H- DY+ Q8136,8137 TO A BOARD (1/2) H DRIVE...

  • Page 28: Block Diagrams

    5-1. BLOCK DIAGRAMS (4) 5-2. CIRCUIT BOARD LOCATION Reference Information IC0006 A(0) A(1) RESISTOR : METAL FILM A(2) A(3) : SOLID A(4) C Board FPRD : NON FLAMMABLE CARBON A(5) A(6) FUSE : NON FLAMMABLE FUSIBLE A(7) : NON FLAMMABLE METAL OXIDE A(8) A(9) VM Board...
  • Page 29 TO H1 BOARD CN2910 A..-32FQ70 VIDEO A 2/6 MUTE A 2/6 TO F1 BOARD CN0981 SCART AUDIO A 2/6 TUNER, AUDIO AMP & SCART CONNECTOR MICRO A 2/6 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL ~ A Board Schematic Diagram [ Tuner, Audio Amp & Scart Connector ] Page 1/6 ~ - 29 -...
  • Page 30 A..-32FQ70 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL MUTE A 1/6 YUV 100 A 3/6 AUDIO PROCESSOR SCART AUDIO TO H1 BOARD A 1/6 CN2909 MICRO A 1/6 VIDEO A 1/6 ~ A Board Schematic Diagram [ Audio Processor ] Page 2/6 ~ - 30 -...
  • Page 31 A..-32FQ70 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL MICRO A 1/6 VIDEO A 1/6 TO D BOARD CN8612 A 4/6 RGB & H DEFLECTION V PROT YUV 100 A 4/6 A 2/6 VDN-OUT A 4/6 H LIN A 4/6 A 4/6 H CENTRE...
  • Page 32 A . . - 3 2 F Q 7 0 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL A 3/6 VERTICAL DEFLECTION & ROTATION COIL A 3/6 VDP-OUT VDN-OUT A 3/6 A 3/6 YUV 100 H LIN A 2/6 H CENTRE VPROT A 3/6...
  • Page 33 A . . - 3 2 F Q 7 0 VIDEO A 1/6 VSYNC A 6/6 HSYNC A 6/6 CVBS TXT A 6/6 VIDEO RF A 6/6 COLOUR DECODER, VIDEO SWITCH RESET A 6/6 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL ~ A Board Schematic Diagram [ Colour Decoder, Video Switch ] Page 5/6 ~ - 33 -...
  • Page 34 A..-32FQ70 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL MICRO A 1/6 VIDEO RF A 5/6 RESET A 5/6 VSYNC A 5/6 HSYNC A 5/6 CVBS TXT A 5/6 INTERFACE ~ A Board Schematic Diagram [ Interface ] Page 6/6 ~ - 34 -...
  • Page 35 ~ A Printed Wiring Board Conductor side A ~ - 35 -...
  • Page 36 ~ A Printed Wiring Board Conductor side B ~ - 36 -...
  • Page 37 ~ A Board Waveforms ~ 2ms/div 5ms/div 744 mVp-p (V) 53 Vp-p (V) 10us/div 20us/div 1.4 Vp-p (H) 688 mVp-p (H) 5ms/div 5ms/div 264 mVp-p (H) 272 mVp-p (H) ~ A Board Location Table (A Side) ~ ~ A Board Location Table (B Side) ~ - 37 -...
  • Page 38 ~ A Board Semiconductor Voltage Table ~ ~ A Board IC Voltage Table ~ ~ A Board Difference Table ~ - 38 -...

  • Page 39: F1 Board Schematic

    ~ F1 Board Schematic Diagram [ Power Switch, Fuse, SIRCS and Stand-By LED ] ~ ~ H1 Board Schematic Diagram [ Front AV Input, Headphone and Control Switches ] ~ F1.-32FQ70 TO A BOARD TO A BOARD A BOARD CN2000 CN2502 CN2300 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL...
  • Page 40 ~ G Board Semiconductor Location Table ~ ~ G Printed Wiring Board Conductor side ~ ~ H1 Printed Wiring Board Conductor side ~ VM Printed Wiring Board Conductor side ~ Note : Portions of the circuit contained within the marked areas as shown have high ~ F1 Printed Wiring Board Conductor side ~ voltages present.

  • Page 41: G Board Schematic

    ~ G Board Schematic Diagram [ Power Supply ] ~ - 41 -...

  • Page 42: C Board Schematic

    FV FOCUS CN7333 TAB (CONTACT) C..-32FQ70 TO FBT R,G,B OUT external J7376 RV7375 110M R7383 CN7300 +200V R7375 R7376 R7300 1/0W 1/0W 1/4W R7385 TO D BOARD D7379 1/2W CN8614 R7325 RD5.6ESB2 D7375 D7376 R7377 1/4W 1SS133T-77 1SS133T-77 HEATER 1/0W C7307 IC7300 R7384...
  • Page 43 ~ C Printed Wiring Board Conductor side ~ ~ C Board Waveforms ~ ~ M2 Printed Wiring Board Conductor side A ~ ~ M2 Printed Wiring Board Conductor side B ~ 10us/div 10us/div 2.16 Vp-p (H) 2.0 Vp-p (H) 10us/div 10us/div 1.9 Vp-p (H) 6.8 Vp-p (H)

  • Page 44: M2 Board Schematic

    ~ M2 Board Schematic Diagram [ Micro Processor ] ~ - 44 -...

  • Page 45: D2 Board Schematic

    TO M2 BOARD CN6804 CN0003 C6852 R6865 SS RESET C6849 HV OVERSHOOT PROTECT 0.01 470p 1/10W Q6813 +12V 2SB709A-QRS-TX R6897 JR6815 R6862 470k R6867 1/10W R6870 D6820 1/10W 220k R6885 1/10W MTZJ-7.5B CHIP 1/10W FB6802 JR6816 Q6817 Q6812 R6896 C6848 2SB709A-QRS-TX R6868 R6869...
  • Page 46 ~ D Printed Wiring Board Conductor side ~ ~ D Board Waveforms ~ ~ D Board IC Voltage Table ~ ~ D Board Semiconductor Voltage Table ~ 10us/div 10us/div 10us/div 10us/div 10us/div 2.44 Vp-p (V) 148 Vp-p (V) 2.36 Vp-p (H) 152 Vp-p (H) 1.12 kVp-p (H) 10us/div...

  • Page 47: D Board Schematic

    ~ D Board Schematic Diagram [ Deflection ] ~ - 47 -...

  • Page 48: Semiconductors

    5-4. SEMICONDUCTORS CXAB070AP PST573IMT LM318P MCZ3001D LM358N LM393DT LM393N M24C16-MN6T(A) CXA1875AM-T4 SAA5665HL/M1D/0358 LM78L05ACZ ( TOP VIEW ) CXA2100AQ-TL SBX3081-51(30) MSP3411G-QA-B11 (TOP VIEW) ( TOP VIEW ) SDA9488X-B23GEG K6T2008V2E-YF70T NJM3404AD-W UPC4558G2 ( TOP VIEW ) LA6500-FA PQ30RV11 STV9379 1 : V IN 2 : V OUT 3 : GND 4 : ON/OFF CONTROL...
  • Page 49 DTA144EK SE135N-LF4 DTC144TKA-T146 2SA1162-G SENSE 2 COLLECTOR 3 GND TDA6111Q/N4 DTA144ESA 2SA933AS-QT 2SC2785-HFE 2SA1837(LBS2S0N) TDA7497 L7809CV/LSY STP5NB40FP STP5NB40(030Y) 2SC5698-CA 2SB734-34 2S5696-SONY-CA VPS9402-A32GEG 2SC2688(5)-LK MSB709-RT1 MSD601-RST1 M1MA152WA-T1 UN2111 UN213 2SK2036(TE85L) (TOP VIEW) BA12T BAO33T BAS216 IRF614-005 RB705D IRF620 SPA07N60C2 2SA2005 2SC5511...
  • Page 50 BAS316-115 FBIU4D7MA-B MMDL914T1 RBV-406B UDZSTE-176.2B S1VB40 ANODE CATHODE BYV98-200-RAS 15/12 CATHODE GS1B460/45 ANODE D1NL20U EGP20G EL1Z GP08D UF4005PKG23 CATHODE TLHK5190 ANODE CATHODE ANODE D2S4MTA1 ERA38-06 MTZJ-T-77-22 ERA85-009 RD5.6ESB2 HZS9.1NB2 RD15ES-B2 MTZJ-13B RD39ES-B2 MTZJ-33B RD5.6ESB2 MTZJ-3.6A 1SS119-25 MTZJ-4.7C 1SS133T-77 CATHODE ANODE - 50 -...

  • Page 51: Ic Block Diagrams

    5-5 IC BLOCK DIAGRAMS A BOARD IC6202/IC6205 BA033T/BA12T REFERENCE VOLTAGE A BOARD IC2500 TDA7497 VOLUME OP AMP MUTE/STBY PROTECTIONS VOLUME OP AMP G BOARD IC6001 MCZ3001D Remote DVLD Internal Driver Sel=34v ref 5v Reg. 10v 15v/8v Level Shift Vsense Control Logic Latch Centre...
  • Page 52 A BOARD IC2000 MSP3411G SBUS Interface I2C Interface DEMODULATOR IDENT SCART Switching Facilities G BOARD IC6003 SE135N-LF4 A BOARD IC5301/IC5302 LA6393DLL A BOARD IC5400 STV9379 A BOARD IC5300 LM358N FLYBACK GENERATOR POWER AMPLIFIER THERMAL PROTECTION - 52 -...
  • Page 53 *A-1603-084-A WOOFER COMPLETE ASSY 20-21 8-598-533-10 FRONTEND BTF-EC411 (KV-32FQ70E/32FQ70K) 1-529-417-11 SPEAKER (8CM) 8-598-529-10 FRONTEND BTF-EU611 (KV-32FQ70U) 7-685-663-71 SCREW +BVTP 4x16 TYPE 2 IT-3 *A-1404-964-A M2 BOARD, COMPLETE *4-093-896-01 REAR COVER *A-1300-579-A A BOARD, COMPLETE (KV-32FQ70B) 7-685-648-79 SCREW (4x16), W(+) P TAPPING...
  • Page 56 < CONNECTOR > 4-382-854-01 SCREW (M3X8), P, SW (+) CN6001 £ * 1-691-291-11 PIN, CONNECTOR (PC BOARD) 5P 4-382-854-01 SCREW (M3X8), P, SW (+) CN6002 £ * 1-508-786-00 PIN, CONNECTOR (5MM PITCH) 2P CN6003 £ * 1-508-765-00 PIN, CONNECTOR (5MM PITCH) 3P <...
  • Page 57 < COIL > R6032 1-249-417-11 CARBON 1/4W R6033 1-215-481-00 METAL 330K 1% 1/4W L6001 1-406-663-21 INDUCTOR 47UH R6034 1-249-389-11 CARBON 1/4W L6002 1-412-527-11 INDUCTOR 15UH R6035 1-260-083-11 CARBON 1/2W L6003 1-412-527-11 INDUCTOR 15UH R6036 1-216-817-11 METAL CHIP 1/10W L6004 1-535-303-00 LEAD, JUMPER (5.0MM) L6005 1-535-303-00 LEAD, JUMPER (5.0MM) R6037...
  • Page 58 C8104 1-115-416-11 CERAMIC CHIP 0.001UF 5.00% 25V C8831 1-102-228-00 CERAMIC 470PF 10.00% 500V C8105 1-126-947-11 ELECT 47UF 20.00% 35V C8832 1-126-941-11 ELECT 470UF 20.00% 25V C8106 1-164-315-11 CERAMIC CHIP 470PF 5.00% 50V C8833 1-126-941-11 ELECT 470UF 20.00% 25V C8107 1-216-685-11 METAL CHIP 0.5% 1/10W C8834...
  • Page 59 8-729-048-47 TRANSISTOR 2SC2688(5)-LK R8141 1-208-818-11 METAL CHIP 0.5% 1/10W Q8802 8-729-048-47 TRANSISTOR 2SC2688(5)-LK R8142 1-208-798-11 METAL CHIP 4.7K 0.5% 1/10W Q8803 8-729-056-16 TRANSISTOR 2SC5698-SONY-CA R8143 1-216-825-11 METAL CHIP 2.2K 5% 1/10W Q8804 8-729-056-17 TRANSISTOR 2SC5696-SONY-CA R8145 1-216-825-11 METAL CHIP 2.2K 5%...
  • Page 60 R8149 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R8808 1-260-340-11 CARBON 1/2W R8150 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R8809 1-260-340-11 CARBON 1/2W R8153 1-216-295-91 SHORT CHIP R8810 1-216-460-11 METAL OXIDE 3.9K 5% R8154 1-208-784-11 METAL CHIP 1.2K 0.5% 1/10W R8811 1-215-896-00 METAL OXIDE 4.7K 5% R8155...
  • Page 61 C6809 1-162-966-11 CERAMIC CHIP 0.0022UF 10.00% 50V D6811 8-719-911-19 DIODE 1SS119-25 D6813 8-719-911-19 DIODE 1SS119-25 C6810 1-162-115-00 CERAMIC 330PF 10.00% 1KV C6811 1-162-115-00 CERAMIC 330PF 10.00% 1KV D6814 8-719-982-21 DIODE MTZJ-30C D6815 8-719-911-19 DIODE 1SS119-25 C6812 1-135-946-22 FILM 47000PF 800V D6816 8-719-110-41 DIODE RD15ESB2 C6813...
  • Page 62 R6801 1-216-841-11 METAL CHIP 1/10W R6875 1-216-863-11 METAL CHIP 3.3M 5% 1/10W R6802 1-216-849-11 METAL CHIP 220K 5% 1/10W R6876 1-215-485-00 METAL 470K 1% 1/4W R6803 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R6877 1-215-485-00 METAL 470K 1% 1/4W R6804 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R6878...
  • Page 63 C1008 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50V C2054 1-126-947-11 ELECT 47UF 20.00% 35V C1009 1-162-925-11 CERAMIC CHIP 68PF 5.00% 50V C2055 1-162-968-11 CERAMIC CHIP 0.0047UF 10.00% 50V C1010 1-162-925-11 CERAMIC CHIP 68PF 5.00% 50V C2057 1-126-964-11 ELECT 10UF 20.00% 50V C1014 1-126-933-11 ELECT 100UF...
  • Page 64 C2517 1-126-960-11 ELECT 20.00% 50V C5106 1-126-933-11 ELECT 100UF 20.00% 16V C2518 1-126-960-11 ELECT 20.00% 50V C5109 1-126-964-11 ELECT 10UF 20.00% 50V C2519 1-126-959-11 ELECT 0.47UF 20.00% 50V C5110 1-126-947-11 ELECT 47UF 20.00% 35V C2521 1-164-489-11 CERAMIC CHIP 0.22UF 10.00% 16V C5111 1-126-964-11 ELECT 10UF...
  • Page 65 C5850 1-126-963-11 ELECT 4.7UF 20.00% 50V C7050 1-162-927-11 CERAMIC CHIP 100PF 5.00% 50V C5851 1-107-826-11 CERAMIC CHIP 0.1UF 10.00% 16V C7051 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25V C5854 1-107-826-11 CERAMIC CHIP 0.1UF 10.00% 16V C7052 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25V C5858 1-107-826-11 CERAMIC CHIP 0.1UF 10.00% 16V...
  • Page 66 D0113 8-719-921-88 DIODE MTZJ-13B D5813 8-719-081-97 DIODE MMDL914T1 D1006 8-719-109-89 DIODE RD5.6ESB2 D5814 1-216-295-91 SHORT CHIP D2014 8-719-929-15 DIODE HZS9.1NB2 D6200 8-719-063-70 DIODE D1NL20U D2015 8-719-929-15 DIODE HZS9.1NB2 D7004 8-719-929-15 DIODE HZS9.1NB2 D2016 8-719-050-38 DIODE M1MA152WK-T1 D7006 1-216-809-11 METAL CHIP 1/10W D2018 8-719-929-15 DIODE HZS9.1NB2...
  • Page 67 L2014 1-408-602-31 INDUCTOR 8.2UH Q2503 8-729-010-29 TRANSISTOR MSD601-RST1 L2500 1-535-303-00 LEAD, JUMPER (5.0MM) Q2504 8-729-010-05 TRANSISTOR MSB709-RT1 L2501 1-535-303-00 LEAD, JUMPER (5.0MM) Q3200 8-729-010-29 TRANSISTOR MSD601-RST1 L3000 1-216-295-91 SHORT CHIP Q3201 8-729-010-29 TRANSISTOR MSD601-RST1 L3004 1-216-295-91 SHORT CHIP Q3202 8-729-010-05 TRANSISTOR MSB709-RT1 L3005 1-216-295-91 SHORT CHIP Q3204...
  • Page 68 R0103 1-216-073-91 RES-CHIP 1/10W R2056 1-216-037-00 RES-CHIP 1/10W R0104 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R2057 1-216-025-11 RES-CHIP 1/10W R0105 1-216-025-11 RES-CHIP 1/10W R2058 1-216-025-11 RES-CHIP 1/10W R0107 1-216-025-11 RES-CHIP 1/10W R2059 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1000 1-216-049-11 RES-CHIP 1/10W R2060 1-216-829-11 METAL CHIP...
  • Page 69 R2516 1-216-081-00 RES-CHIP 1/10W R3219 1-216-821-11 METAL CHIP 1/10W R2517 1-216-841-11 METAL CHIP 1/10W R3220 1-216-837-11 METAL CHIP 1/10W R2518 1-216-049-11 RES-CHIP 1/10W R3221 1-216-837-11 METAL CHIP 1/10W R2519 1-216-833-11 METAL CHIP 1/10W R3222 1-216-837-11 METAL CHIP 1/10W R2520 1-216-025-11 RES-CHIP 1/10W R3223 1-216-837-11 METAL CHIP...
  • Page 70 R5148 1-216-809-11 METAL CHIP 1/10W R5345 1-208-832-11 METAL CHIP 120K 0.5% 1/10W R5149 1-218-833-11 METAL CHIP 0.5% 1/10W R5346 1-216-849-11 METAL CHIP 220K 5% 1/10W R5150 1-249-414-11 CARBON 1/4W R5347 1-216-833-11 METAL CHIP 1/10W R5151 1-249-454-11 CARBON 1/4W R5349 1-216-043-91 RES-CHIP 1/10W R5152 1-249-413-11 CARBON...
  • Page 71 R5898 1-216-832-11 METAL CHIP 8.2K 5% 1/10W X3200 1-781-946-21 VIBRATOR, CRYSTAL R5899 1-216-863-11 METAL CHIP 3.3M 5% 1/10W X5800 1-767-127-11 VIBRATOR, CERAMIC R6200 1-218-831-11 METAL CHIP 0.5% 1/10W R6201 1-218-839-11 METAL CHIP 0.5% 1/10W R6202 1-249-395-11 CARBON 1/4W < TUNER > R7007 1-216-049-11 RES-CHIP 1/10W...
  • Page 72 C7385 1-162-913-11 CERAMIC CHIP 8PF 0.50PF 50V R7325 1-249-417-11 CARBON 1/4W C7387 1-162-911-11 CERAMIC CHIP 6PF 0.50PF 50V R7328 1-216-824-11 METAL CHIP 1.8K 5% 1/10W C7388 1-162-913-11 CERAMIC CHIP 8PF 0.50PF 50V R7329 1-260-095-11 CARBON 1/2W C7390 1-162-911-11 CERAMIC CHIP 6PF 0.50PF 50V R7330 1-215-903-11 METAL OXIDE...
  • Page 73 < CONNECTOR > < RESISTOR > CN0981 * 1-564-507-11 PLUG, CONNECTOR 4P JR0901 1-216-864-11 SHORT CHIP CN6400 £ * 1-580-843-11 PIN, CONNECTOR (POWER) JR2901 1-216-864-11 SHORT CHIP CN6401 £ * 1-691-291-11 PIN, CONNECTOR (PC BOARD) 5P JR2902 1-216-864-11 SHORT CHIP CN6403 1-695-915-11 TAB (CONTACT) R0901...
  • Page 74 C0024 1-115-416-11 CERAMIC CHIP 0.001UF 5.00% 25V FB0031 1-414-760-21 FERRITE C0025 1-162-962-11 CERAMIC CHIP 470PF 10.00% 50V FB0032 1-414-760-21 FERRITE C0026 1-162-962-11 CERAMIC CHIP 470PF 10.00% 50V C0027 1-162-962-11 CERAMIC CHIP 470PF 10.00% 50V < IC > C0028 1-126-934-11 ELECT 220UF 20.00% 16V IC0001...
  • Page 75 R0040 1-216-809-11 METAL CHIP 1/10W R0118 1-216-813-11 METAL CHIP 1/10W R0041 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R0119 1-216-813-11 METAL CHIP 1/10W R0042 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R0120 1-216-813-11 METAL CHIP 1/10W R0043 1-216-803-11 METAL CHIP 1/10W R0121 1-216-813-11 METAL CHIP 1/10W R0044...
  • Page 76 R7420 1-249-421-11 CARBON 2.2K 5% 1/4W < DIODE > R7421 1-249-389-11 CARBON 1/4W R7422 1-249-405-11 CARBON 1/4W D7400 8-719-991-33 DIODE 1SS133T-77 R7423 1-215-915-11 METAL OXIDE D7401 8-719-991-33 DIODE 1SS133T-77 R7427 1-216-025-11 RES-CHIP 1/10W D7402 1-535-303-00 LEAD, JUMPER (5.0MM) D7403 8-719-991-33 DIODE 1SS133T-77 R7428 1-216-033-00 RES-CHIP 1/10W...

  • Page 77: Picture Tube

    1-452-032-00 MAGNET, DISK; 10MM *4-046-772-01 BAG, PROTECTION *4-087-594-01 INDIVIDUAL CARTON *4-094-270-01 CUSHION UPPER *4-094-271-01 CUSHION LOWER 4-093-901-41 MANUAL, INSTRUCTION (KV-32FQ70B) (GERMAN/ITALIAN/FRENCH/DUTCH) 4-093-901-51 MANUAL, INSTRUCTION (KV-32FQ70B) (ENGLISH) 4-093-901-11 MANUAL, INSTRUCTION (KV-32FQ70E) (GERMAN/TURKISH/GREEK) 4-093-901-21 MANUAL, INSTRUCTION (KV-32FQ70E) (ITALIAN) 4-093-901-31 MANUAL, INSTRUCTION (KV-32FQ70E) (NORWEGIAN/PORTUGUESE/SWEDISH/FINNISH/ DANISH/SPANISH)
  • Page 78 • User programmable Functional Check through Infrared • Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.

This manual is also suitable for:

Fd trinitron kv-32fq70uFd trinitron kv-32fq70eFd trinitron kv-32fq70k

Table of Contents