Page 1: Table Of Contents
Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo cassette with CD AM/FM stereo with CD AM/FM stereo cassette (CD changer compatible) Climate Controls Lights Bulb replacement Interior lamps Driver Controls Windshield wiper/washer control Steering wheel adjustment Speed control Locks and Security...
Page 2 Ford Motor Company. Ford may change the contents without notice and without incurring obligation.
Page 3: Introduction
The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving For more information on Ford Motor Company and its products visit the following website: In the United States: www.ford.com In Canada: www.ford.ca...
Page 4 Introduction This Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available. Remember to pass on the Owner’s Guide when reselling the vehicle.
Page 5 Introduction Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment We must all play our part in protecting the environment.
Page 6 Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Page 7 Introduction Notice to owners of Cobra vehicles Before you drive your vehicle, be sure to read the “SVT Cobra Owner’s Guide Supplement.” This book contains important operation and maintenance information. MIDDLE EAST/NORTH AFRICA VEHICLE SPECIFIC INFORMATION For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner Guide;...
Page 8 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Child Seat Tether Installation Warning Anchorage Anti-Lock Brake Brake System System Brake Fluid -...
Page 9 Introduction Vehicle Symbol Glossary Interior Luggage Compartment Panic Alarm Release Symbol Engine Oil Engine Coolant Engine Coolant Do Not Open When Temperature Avoid Smoking, Battery Flames, or Sparks Battery Acid Explosive Gas Power Steering Fan Warning Fluid Maintain Correct Emission System Fluid Level Passenger Engine Air Filter...
Page 10: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES Base instrument cluster 60 70 RPMX1000 80 100 120 1 10 SELECT/RESET km/h 0 0 0 0 0 FUEL DOOR SERVICE CHECK BRAKE THEFT ENGINE FUEL FUEL SOON Optional instrument cluster RPMX1000 120 140 km/h SELECT/RESET 0 0 0 0 0...
Page 11 Instrument Cluster Charging system Illuminates when the battery is not charging properly. Air bag readiness Illuminates to confirm that the air bags (front or side) are operational. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately.
Page 12 Instrument Cluster recommended octane and/or properly installing and securely tightening the fuel cap. After three driving cycles without these or any other temporary malfunctions present, the light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required.
Page 13 Instrument Cluster Low fuel Illuminates when the fuel level in the fuel FUEL tank is at, or near, empty (refer to Fuel gauge in this chapter for more information). O/D off (if equipped) Illuminates when the overdrive function has been turned OFF using the transmission control switch (TCS) on the gearshift.
Page 14 Instrument Cluster illuminated and parking brake is off. Refer to Brakes in the Driving chapter for more information. Brake system warning To confirm the brake BRAKE system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position (alternatively for some vehicles when the ignition is moved from the ON position to START position, the light will momentarily illuminate prior to reaching...
Page 15: Gauges
Instrument Cluster Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the key is removed from the ignition and the driver’s door is opened. GAUGES Base instrument cluster gauges 60 70 RPMX1000 80 100 120 1 10 km/h SELECT/RESET 0 0 0 0 0...
Page 16 Instrument Cluster Never remove the coolant reservoir cap while the engine is running or hot. Steam and scalding liquid from a hot cooling system can burn you badly. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate.
Page 17 Instrument Cluster When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel. The FUEL DOOR icon and arrow indicates which side of the vehicle the fuel filler door is located. Speedometer Indicates the current vehicle speed.
Page 18 Instrument Cluster • Base instrument cluster gauge • Optional instrument cluster gauge Trip odometer Registers the kilometers (miles) of individual journeys. Press and release the reset button until a ’T’ appears in the display (this represents the trip mode). Press and hold the button for three seconds to reset.
Page 19: Entertainment Systems
Entertainment Systems PREMIUM AM/FM STEREO/CASSETTE/SINGLE DISC VOL PUSH ON FM 1 MUTE TAPE AUTO DOLBY B NR SEEK TUNE SCAN BASS TREB FADE SIDE 1-2 COMP SHUFFLE Volume/power control Press the control to turn the audio system VOL - PUSH ON on or off.
Page 20 Entertainment Systems Press the BASS control then press: • to decrease the bass output and • to increase the bass output. Treble adjust The treble adjust BASS TREB control allows you to increase or decrease the audio system’s treble output. Press the TREB control then press: •...
Page 21 Entertainment Systems Press the FADE control then press: • to shift the sound to the front • to shift the sound to the rear. Seek function The seek function control works in radio, tape or CD mode. Seek function in radio mode •...
Page 22 Entertainment Systems Scan function The scan function SCAN works in radio, tape or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape.
Page 23 Entertainment Systems Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1.
Page 24 Entertainment Systems If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. These stations are temporarily stored in the memory preset controls (until deactivated) and are accessed in the same manner as your original presets.
Page 25 Entertainment Systems The CLK control will allow you to switch AUTO between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 seconds, when the radio is turned on, and then revert to clock information.
Page 26 Entertainment Systems playing. If returning from radio or tape mode, CD play will begin where it stopped last. Press the CD control to toggle between single CD and CD changer (if equipped). Rewind The rewind control works in tape and CD modes.
Page 27 Entertainment Systems Dolby noise reduction Dolby noise reduction operates in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the Dolby noise reduction. Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation.
Page 28 Entertainment Systems Mute mode Press the MUTE control to mute the playing media. Press the MUTE control MUTE again to return to the playing media. MACH MP3 MUSIC SYSTEM 1. ON/OFF and volume 11. CD control control 12. MP3 directory control 2.
Page 29 Entertainment Systems Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower the volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 30 Entertainment Systems Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. MP3 functions Your audio system is equipped with MP3 capability which allows you to listen to songs in MP3 flat file mode and MP3 directory mode.
Page 31 Entertainment Systems numbers each MP3 track on the disc (denoted by the .mp3 file extension) from T001 to T255. • MP3 directory mode represents a directory structure consisting of one level of directories (folders). The CD player sequentially numbers all MP3 tracks on the disc (denoted by .mp3 extension) and all directories containing MP3 files, from 01–01 to 99–99.
Page 32 Entertainment Systems Press and hold the SEEK control to quickly seek through all tracks in MP3 flat file mode or all tracks in the current MP3 directory. Note: If a track has been playing for three seconds or more and you press on the SEEK control, the player will replay that track from the beginning.
Page 33 Entertainment Systems scan function is enabled. When the end of the disc is reached, the player will continue to scan from the first track forward. Press SCN again to disengage scan mode. Scan function in MP3 directory mode The scan function in MP3 directory mode allows you to briefly audition all tracks within the current directory on the MP3 disc.
Page 34 Entertainment Systems Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Page 35 Entertainment Systems To set the minutes, press and hold the CLK control while performing the following functions: • Press on the TUNE DIR control to decrease the minutes. • Press on the TUNE DIR control to increase the minutes. Release the CLK control to save the clock settings. Press the CLK control again to return the display to radio mode.
Page 36 TXXX (XXX=current track number) to XX-XX (directory —track number). Note: If the car’s ignition is turned off and on again, play will begin at the beginning of the last song played. If the radio was powered off by the VOL control, play will start where it last left off.
Page 37 Entertainment Systems • Press on TUNE DIR to revert to the previous directory on the MP3 disc. If the current directory is the first directory on the disc, pressing will select the last directory on the disc. Press and hold for fast selection. Eject function Press the control to stop and eject a disc.
Page 38 Entertainment Systems Shuffle feature The shuffle feature works in CD mode, MP3 flat file mode and MP3 directory mode. Shuffle feature in CD mode The shuffle feature plays all tracks on the current disc in random order. • Press the SHUFFLE control to engage random play.
Page 39 Entertainment Systems • To select another random track on the disc, press on the SEEK control. • Press SCN to scan through random tracks. The track number will flash in the display. The shuffle function will remain enabled. • Press SHUFFLE again to disengage the shuffle feature.
Page 40 Entertainment Systems To shuffle tracks in another directory, press on the TUNE DIR control to select the desired directory. The shuffle function still remains enabled. Press the SHUFFLE control again to disengage the SHUFFLE feature. SHUF and OFF will briefly display and the current track will continue to play.
Page 41 Entertainment Systems • Rotate the volume control to advance or reverse through the tracks. The MP3 icon will blink in the display while the MACH track function is enabled. When the desired track is reached, the selected track will begin play after a two second delay. To disengage the MACH track function, press the TRACK control again.
Page 42 Entertainment Systems Saving and naming MP3 files • Your MACH MP3 music system supports discs containing up to 255 files in 255 directories. Discs containing more than 255 files will not play. • Always save MP3 files with the .mp3 extension. The player recognizes an MP3 file by the .mp3 extension, so MP3 files saved with different extensions will not be played.
Page 43 Entertainment Systems MACH 1000 SOUND SYSTEM RADIO (CD CHANGER COMPATIBLE) MACH 1000 AUDIO SYSTEM Your vehicle may be equipped with the MACH 1000 audio system. This system is equipped with a rack of amplifiers in the trunk of the vehicle. Do not store or rest items on the amplifier rack, as this could cause damage to the amplifiers and void your warranty.
Page 44 Entertainment Systems at a “nominal” listening level when the ignition switch is turned back on. Speed sensitive volume With this feature, radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. The recommended level for speed sensitive volume is from level 1 through level 3.
Page 45 Entertainment Systems Treble adjust The treble adjust BASS control allows you to increase or decrease TREB the audio system’s treble output. Press the TREB control. Use the SEL control to increase or decrease the amount of treble. Speaker balance adjust Speaker sound distribution can be adjusted between the...
Page 46 Entertainment Systems Seek function in radio mode • Press to find the next listenable station down the frequency band. SEEK DOWN will display. • Press to find the next listenable station up the frequency band. SEEK UP will display. Seek function in CD mode •...
Page 47 Entertainment Systems AM/FM select The AM/FM select control works in radio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play.
Page 48 Entertainment Systems preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the display as the frequency band is scrolled through.
Page 49 Entertainment Systems Tune adjust in radio mode • Press to move to DISC TUNE the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there).
Page 50 Entertainment Systems If your vehicle is equipped with a CD changer, pressing the CD control again will allow you to toggle between accessing the multi disc system and the CD changer. The display will read CD or CDDJ. Display description Six circles are always lit in the digital display.
Page 51 Entertainment Systems This six disc CD player is equipped with a CD door. Compact discs should only be inserted into the player after the door has been opened by the player. Do not attempt to force the door open. Compact discs should only be loaded by pressing the LOAD control.
Page 52 Entertainment Systems If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF. Auto eject Press and momentarily hold the EJ control to engage auto eject.
Page 53 Entertainment Systems On Premium audios, press the COMP control until COMP ON is displayed. Menu mode The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated.
Page 54 Entertainment Systems FIND type — Allows you to select your desired FM program type and search for that selection. SHOW — Allows you to select from NAME (displays the name of the radio station), TYPE (displays the RDS program type: rock, jazz, etc.), or NONE (deactivates the RDS display).
Page 55 Entertainment Systems To disengage the feature, press the MENU control until TRAFFIC ON displays. Press the SEL control. The display will read TRAFFIC OFF. Traffic announcements are not available in most U.S. markets. Program type This feature allows you to search for RDS stations selectively by their program type.
Page 56 Entertainment Systems Digital signal processing The digital signal processing (DSP) feature allows you to change the signal mode to suit your listening tastes. Press the DSP control to access the DSP menu. Use the SEL control to select the desired signal mode (the selected mode will appear in the display).
Page 57 12cm audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 58 Entertainment Systems • The player’s internal temperature is above 60°C (140°F). Allow the player to cool down before operating. • A disc with format and dimensions not within industry standards is inserted. MP3 DISC QUALITY FACTORS The MACH MP3 music system is designed for use with CD-DA (regular audio discs), CD-R and CD-RW discs.
Page 59 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 60 Entertainment Systems CLEANING CASSETTE PLAYER (IF EQUIPPED) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation. CASSETTE AND CASSETTE PLAYER CARE • Use only cassettes that are 90 minutes long or less.
Page 61 Entertainment Systems RADIO RECEPTION FACTORS Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.”...
Page 62: Climate Controls
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 63 Climate Controls • O (Off) – Outside air is shut out and the fan will not operate. This mode may reduce undesirable odors from entering the vehicle but may increase the possibility of interior window fogging. • (Floor) – Distributes outside air through the floor ducts.
Page 64 Climate Controls • Under normal weather conditions, do not leave your vehicle in the Max A/C (if equipped), recirculation mode (if equipped) or Off mode when turning off the vehicle. • Under snowy or dirty weather conditions, leave your vehicle in the Max A/C (if equipped), recirculation mode (if equipped) or Off mode when turning off the ignition.
Page 65: Lights
Lights HEADLAMP CONTROL • Pull the headlamp control toward you to the first position to turn on the parking lamps, tail lamps, license plate lamps and marker lamps. • Pull the headlamp control toward you to the outer position to turn on the headlamps (in addition to the previous lamps).
Page 66 Lights Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
Page 67 Lights AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. Headlamp vertical aim adjustment 1.
Page 68: Interior Lamps
Lights 4. On the wall or screen you will observe a light pattern with flat edges at the top of the beam pattern. If the flat edges are not at the horizontal reference line, the beam will need to be adjusted. 5.
Page 69 Lights BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: • Headlamps • Tail lamps • Brakelamps • High-mount brakelamp • Turn signal lamps • Backup lamps • License plate lamp Do not remove lamp bulbs unless they will be replaced immediately.
Page 70 Lights Function Trade Number Visor vanity lamp Glove compartment Rearview mirror map lamps Fog lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer. Interior bulbs Check the operation of the following interior bulbs frequently: •...
Page 71 Lights 4. Disconnect the electrical connector from the bulb by pulling rearward. 5. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb.
Page 72 Lights 4. Install the headlamp on vehicle by aligning the lamp with the rear snap retainers, push to seat and secure with two retainer pins. 5. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again.
Page 73 Lights Replacing high-mount brakelamp bulbs 1. Open trunk. 2. Inside trunk, locate access hole under the rear decklid. 3. Remove the bulb socket by rotating it 45 degrees and pulling it out of the lamp assembly. 4. Carefully pull bulb straight out of socket and push in new bulb.
Page 74 Lights Replacing license plate lamp bulbs 1. Open trunk and remove bulb socket from the trunk lid by turning counterclockwise. 2. Pull the bulb straight out of the socket and push in the new bulb. 3. Install the bulb socket in trunk lid by turning clockwise.
Page 75: Driver Controls
Check the wiper blades for wear at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades. Checking the wiper blades...
Page 76 Driver Controls Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down...
Page 77 Driver Controls OVERHEAD STORAGE NET (IF EQUIPPED) Be sure to secure objects when placed in the storage net in order to help reduce the risk that they become projectiles in the event of a collision. AUXILIARY POWER POINT Power outlets are designed for accessory plugs only.
Page 78 Driver Controls • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. Express down To make the driver window open fully without holding the window control, press the bottom portion of the driver window control completely down and release...
Page 79: Speed Control
Driver Controls POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1. Move the mirror selector control all the way to the left to adjust the left mirror or all the way to the right to adjust the right mirror.
Page 80 Driver Controls To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET ACCEL. For speed control to RESUME operate, the speed control must be ON...
Page 81 Driver Controls To set a higher set speed • Press and hold SET ACCEL. Release the RESUME control when the desired vehicle ACCEL speed is reached or • Press and release COAST SET ACCEL to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or •...
Page 82 Driver Controls To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed •...
Page 83 Driver Controls OVERDRIVE CONTROL (IF EQUIPPED) Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through all available gears. Deactivating overdrive Press the Transmission Control Switch (TCS) located on the gearshift.
Page 84 Driver Controls CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • Dual cupholders • Auxiliary power point • Coin holder slots (if equipped) • Convertible top control (if equipped) Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Page 85 Driver Controls Lowering the convertible top The convertible top can be lowered with the side windows either up or down. The convertible top will not operate unless the parking brake is engaged. Do not lower the top while the vehicle is moving because the top may be severely damaged.
Page 86 Driver Controls Installation of the boot 1. Push boot rearward and engage boot under the body molding at the rear and sides. 2. Fasten snap on boot to quarter trim panel on both sides of the vehicle. 3. Insert boot tongue into groove located on rear of seat.
Page 87 Driver Controls Raising the convertible top The convertible top will not operate unless the parking brake is engaged. Do not raise the top while the vehicle is moving because the top may be severely damaged. To raise the convertible top: 1.
Page 88: Locks And Security
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLock Passive Anti-Theft System for more information.
Page 89: Locks
Locks and Security To open the luggage compartment door (lid) from the inside, pull the illuminated “T” shaped handle and push up on the trunk lid. The material that the handle is made of will glow for hours in the darkness of the luggage compartment following brief exposure to...
Page 90 Locks and Security REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 91 Locks and Security Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within three seconds. The doors will lock again, the horn will chirp and the lamps will flash. If any of the doors are ajar, the horn will make two quick chirps and the chime may sound, reminding you to properly close all doors.
Page 92 Locks and Security Replacing the batteries The transmitter is powered by two coin type three-volt lithium batteries. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by: •...
Page 93: Anti-Theft System
This system is designed to prevent the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start...
Page 94 Locks and Security systems. Use of these systems may result in vehicle starting problems and a loss of security protection. THEFT INDICATOR The theft indicator is located on top of the instrument panel. When the ignition is in the OFF position, the indicator will flash once every 2 seconds to indicate the SecuriLock system is...
Page 95 OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Ford coded key. If your keys are lost or stolen you will need to do the following: •...
Page 96 Locks and Security Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure.
Page 97 Locks and Security If successful, the new coded key(s) will start the vehicle’s engine and the theft indicator will illuminate for three seconds and then go out. If not successful, the new coded key(s) will not start the vehicle’s engine and the theft indicator will flash on and off and you may repeat steps 1 through 6.
Page 98: Seating And Safety Restraints
Seating and Safety Restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 99 Seating and Safety Restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness. Press the other side of the control to adjust softness.
Page 100 Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. The control is located on the front outboard corner of the driver’s seat. Press front to raise or lower the front portion of the seat cushion.
Page 101: Safety Restraints
Seating and Safety Restraints outboard back of the seat. The seatback locks automatically when returned to the normal position. The rotating boot on the front seat belt is designed to allow rear seat entry/exit. To enter the rear seat: 1. Remove safety belt from safety belt guide on top of front seat.
Page 102 Seating and Safety Restraints To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Page 103 Seating and Safety Restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Combination lap and shoulder belts Before fastening the safety belt, make sure the shoulder belt passes through the belt guide on the top of the seatback.
Page 104 Seating and Safety Restraints positions to help further reduce the risk of injury in the event of a head-on collision. • This safety belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest.
Page 105 Seating and Safety Restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode •...
Page 106 This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Ford Motor Company recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision.
Page 107 Seating and Safety Restraints BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.
Page 108 Seating and Safety Restraints If... Then... The driver’s safety belt is not The BeltMinder feature is buckled approximately 5 activated - the safety belt seconds after the safety belt warning light illuminates and warning light has turned the warning chime sounds off...
Page 109 Seating and Safety Restraints Reasons given... Consider... “I was in a hurry” Prime time for an accident. BeltMinder reminds us to take a few seconds to buckle up. “Seat belts don’t Safety belts, when used properly, work” reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks.
Page 110 Seating and Safety Restraints The BeltMinder feature can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set. • The gearshift is in P (Park) (automatic transmission) or the neutral position (manual transmission).
Page 111 Seating and Safety Restraints 7. Confirmation of disabling BeltMinder is provided by the safety belt warning light flashing four times per second for three seconds. 8. Confirmation of enabling BeltMinder is provided • The safety belt warning light flashing four times per second for three seconds.
Page 112 In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity. This information will assist Ford Motor Company in servicing the vehicle...
Page 113 Seating and Safety Restraints and in helping to better understand real world collisions and further improve the safety of future vehicles. Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper...
Page 114 Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body...
Page 115 Seating and Safety Restraints positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag.
Page 116 Seating and Safety Restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag.
Page 117 Seating and Safety Restraints system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately.
Page 118 Seating and Safety Restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags.
Page 119 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better.
Page 120 Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? •...
Page 121 Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs.
Page 122 Seating and Safety Restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle.
Page 123 (if equipped) section in this chapter. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 124 Seating and Safety Restraints Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Page 125 Seating and Safety Restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it.
Page 126 Seating and Safety Restraints 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward.
Page 127 Seating and Safety Restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether...
Page 128 Seating and Safety Restraints 5. Clip the tether strap to the anchor as shown. For Convertible only: The tether anchors on the convertible are located on the lower backside of the seatback. 4. Access tether anchors located behind the seatback and pull away vinyl flap to expose anchors.
Page 129 Seating and Safety Restraints 6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Page 130 Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. For manual transmission, you must depress the ignition release lever. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal.
Page 131 Driving When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter. Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of...
Page 132 Driving Before starting the vehicle: 1. Make sure all vehicle occupants have buckled their safety belts. For more information on safety belts and their proper usage, refer to the Seating and safety restraints chapter. 2. Make sure the headlamps and vehicle accessories are off.
Page 133: Air Bags
Driving • steering wheel is turned when getting in or out of the vehicle 60 70 RPMX1000 80 100 120 1 10 km/h SELECT/RESET 0 0 0 0 0 FUEL DOOR SERVICE CHECK BRAKE THEFT ENGINE FUEL FUEL SOON RPMX1000 120 140 SELECT/RESET km/h...
Page 134: Driving
Driving Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts.
Page 135 Driving To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately.
Page 136: Brakes
Driving Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris. BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance.
Page 137 Driving The BRAKE warning BRAKE lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission).
Page 138 Driving self-check after you start the engine and begin to drive away. A brief mechanical noise may be heard during this test. This is normal. If a malfunction is found, the ABS warning light will come on. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by a qualified service technician.
Page 139 Driving and, providing there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a controlled stop. • The anti-lock system does not reduce stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. •...
Page 140: Traction Control/Advancetrac
Driving If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, the condition could be caused by any of the following: •...
Page 141 Driving During Traction Control operation, the traction control active light will illuminate, you may hear an electric motor type of sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator. This is normal system behavior. The Traction Control on/off switch, located below the radio,...
Page 142: Transmission Operation
Driving AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed:...
Page 143 Driving Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.
Page 144 Driving Driving with a 4–speed automatic transmission (if equipped) Use the following procedure to put your vehicle in gear. 1. Start the engine. 2. Depress and hold the brake pedal. 3. Push and hold the thumb button. 4. Move gearshift lever out of P (Park).
Page 145 Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
Page 146 Driving (Overdrive) can be deactivated by pressing the transmission control switch on the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster. Drive – Not shown on the display. Activate by pressing the transmission control switch on the gearshift lever with the gearshift in the position.
Page 147 Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. Transmission operates only in Second gear. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
Page 148 Driving When starting a vehicle with a manual transmission, you must: 1. Make sure the parking brake is fully set. 2. Depress the clutch pedal fully. 3. Put the gearshift lever in Neutral. 4. Turn the ignition to position 5 (START) to start the engine, let the engine idle for a few seconds.
Page 149 Driving Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 18 km/h (11 mph) 2 - 3 31 km/h (19 mph) 3 - 4 48 km/h (30 mph) 4 - 5 64 km/h (40 mph) Parking your vehicle 1.
Page 150 Driving Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse You must be at a complete stop to shift into R (Reverse). You can shift into R (Reverse) only by moving the gearshift lever through the neutral plane.
Page 151: Vehicle Loading
Driving Removing key from ignition • Turn the ignition key to position 3 (OFF). • Push the release lever forward and rotate the key towards you and remove. DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall.
Page 152 Driving • Payload: Combined maximum allowable weight of cargo, occupants and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. • GVW (Gross Vehicle Weight): Base curb weight plus payload weight. The GVW is not a limit or a specification.
Page 153 Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. TRAILER TOWING Your vehicle is not equipped to tow. No towing packages are available through Ford or Lincoln/Mercury dealers.
Page 154 If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician. See your local dealer for driveshaft removal/installation.
Page 155: Roadside Emergencies
• 24–hours, seven days a week • for the New Vehicle Limited Warranty period of three years or 60 000 km (36 000 miles), whichever occurs first on Ford and Mercury vehicles, and four years or 80 000 km (50 000 miles) on Lincoln vehicles.
Page 156: Hazard Flasher Switch
WARRANTY In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside...
Page 157: Fuel Pump Shut-Off Switch
Roadside Emergencies • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously. • Depress control again to turn the flashers off. FUEL FUEL PUMP SHUT-OFF SWITCH RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has...
Page 158: Fuses And Relays
Roadside Emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
Page 159 Roadside Emergencies To remove a fuse use the fuse puller tool provided on the fuse panel cover. OWNERS MANUAL FUSE INFO The fuses are coded as follows: Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Cigar lighter Engine controls —...
Page 160 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description — Not used Speed control servo, Shift lock actuator Electronic flasher Power mirror switch, GEM, Anti-theft relay, Power door locks, Door ajar switches Convertible top switch Instrument cluster and Engine control memory —...
Page 161 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description — Not used Brake lamp — Not used 20A CB Power windows — Not used Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
Page 162 Roadside Emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description Relay 1 — Fog lamp interrupt Relay 2 — Int. wiper Relay 3 — Wiper HI/LO Relay 4 — Starter Relay 5 —...
Page 163: Changing Tires
Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description 30A** Rear window defrost control 40A** Power windows, Power locks 30A* MACH 1000 left amplifiers 20A* Fuel pump 30A* MACH 1000 right amplifiers 20A* Horn 20A* Anti-lock brake system 30A* Power seats —...
Page 164 • tow a trailer • use tire chains • drive through an automatic car wash, because of the vehicle’s reduced ground clearance • try to repair the temporary spare tire or remove it from its wheel •...
Page 165 Roadside Emergencies If the vehicle slips off the jack, you or someone else could be seriously injured. 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park) or R (manual transmission), turn engine OFF, and block the diagonally opposite wheel.
Page 166 Roadside Emergencies 5. Put the jack in the jack notch next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground. Never use the rear differential as a jacking point. To lessen the risk of personal injury, do not put any part of your body...
Page 167 If the lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln Mercury dealer who has access to the master set of keys. Do not use an impact wrench with the anti-theft key.
Page 168 Roadside Emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push-start your vehicle.
Page 169 Roadside Emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 170: Jump Starting
Roadside Emergencies 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Page 171 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2.
Page 172 Roadside Emergencies 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 173: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If your vehicle is to be towed from the rear using...
Page 174: Customer Assistance
Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could...
Page 175 Ford Customer Relationship Center to find an authorized dealership to help you. In the United States:...
Page 176 Magnuson-Moss Warranty Act or state replacement or repurchase laws. FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional...
Page 177 Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage.
Page 178 Customer Assistance Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: • a non-Ford product • a non-Ford dealership • sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle’s performance as...
Page 179 • The file number assigned to your application. • The toll-free phone number of the DSB’s independent administrator. Your dealership and a Ford Motor Company representative will then be asked to submit statements. To properly review your case, the Board needs the following information: •...
Page 180 Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 181 CAMVAP decisions are fast, fair, and final; the arbitrator’s award is binding both to you and Ford of Canada. CAMVAP services are available in all territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.
Page 182 Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. In the United States, using leaded fuel may also result in difficulty importing your vehicle back into the U.S.
Page 183 Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if...
Page 184: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (or 366–0123 in the Washington D.C.
Page 185: Cleaning
• Remove any exterior accessories, such as antennas, before entering a car wash. • Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible.
Page 186 • Never apply any cleaning chemical to hot or warm wheel rims or covers. • Some automatic car washes may cause damage to the finish on your wheel rims or covers. Chemical-strength cleaners, or cleaning chemicals,...
Page 187 Cleaning • Do not spray with cold water to avoid cracking the engine block or other engine components. • Spray Engine Shampoo and Degreaser (F4AZ-19A536–A) on all parts that require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaning the engine.
Page 188 These may include hot wax treatments used by commercial car washes, tree sap, or other organic contamination. To clean these items, please follow these tips: • The windshield or rear window may be cleaned with a non-abrasive cleaner such as Ultra Clear Spray Glass Cleaner (E4AZ-19C507–AA), available...
Page 189 Cleaning • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the painted surfaces. Interior For fabric, carpets, cloth seats and safety belts: •...
Page 190 • Do not use stiff bristle brushes or abrasive materials or cleaners. • Hot waxes applied by commercial car washes can affect the cleanability of vinyl material. • Using high water pressure or wand-type car washes against the convertible top and windows may cause water leaks and possible seal damage.
Page 191 Ford Custom Bright Metal Cleaner Motorcraft Premium Car Wash Concentrate Motorcraft Carlite Glass Cleaner (Canada only) Ford Spot and Stain Remover* Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra-Clear Spray Glass Cleaner (not available in Canada)
Page 192: Maintenance And Specifications
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 193 Maintenance and Specifications 3. Block the wheels to prevent the vehicle from moving unexpectedly. • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. Turn off the engine and remove the key. 4.
Page 194: Hood
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
Page 195: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.8L OHV V6 engine 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Power distribution box 5. Windshield washer fluid reservoir 6. Battery 7. Power steering fluid reservoir 8.
Page 196 Maintenance and Specifications 4.6L SOHC V8 engine 1. Engine oil dipstick 2. Brake fluid reservoir 3. Power distribution box 4. Windshield washer fluid reservoir 5. Battery 6. Engine coolant reservoir 7. Power steering fluid reservoir 8. Engine oil filler cap 9.
Page 197: Engine Oil
In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specification ESR-M17P5–A. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 198 Maintenance and Specifications 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 3.8L V6 engine • 4.6L SOHC V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again.
Page 199 Maintenance and Specifications • 3.8L V6 engine • 4.6L SOHC V8 engine • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated.
Page 200 If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.
Page 201: Battery
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules.
Page 202 Maintenance and Specifications Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting...
Page 203 Maintenance and Specifications 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6.
Page 204 Maintenance and Specifications ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals in the scheduled maintenance guide. The coolant concentration should be maintained at 50/50 coolant and water, which equates to a freeze point of -36° C (-34° F). Coolant concentration testing is possible with a hydrometer or antifreeze tester (such as the Rotunda Battery and Antifreeze Tester, 014–R1060).
Page 205 Maintenance and Specifications • 4.6L SOHC V8 engine When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” as listed on the engine coolant reservoir. •...
Page 206 The cooling system in your vehicle is filled with either green-colored Motorcraft Premium Engine Coolant meeting Ford specification ESE-M97B44–A or yellow-colored Motorcraft Premium Gold Engine Coolant meeting Ford Specification WSS-M97B51–A1. To determine your vehicle’s coolant type (color), check your coolant reservoir.
Page 207 • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled Engine Coolant section). To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap.
Page 208 Maintenance and Specifications The following procedure should be used when refilling the cooling system of a 3.8L V6 engine after it has been drained or become extremely low. 1. Remove the cap from the engine coolant reservoir. 2. Open the cooling system vent plug.
Page 209 Maintenance and Specifications Engine coolant refill procedure-4.6L V8 engine The following procedure should be used when refilling the cooling system of a 4.6L V8 engine after it has been drained or become extremely low. 1. Remove the pressure relief cap from the engine coolant reservoir as previously outlined.
Page 210 Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored).
Page 211 Maintenance and Specifications • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you...
Page 212 Maintenance and Specifications WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 213 Maintenance and Specifications injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation.
Page 214 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.
Page 215 Maintenance and Specifications The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel...
Page 216 Canada, look for fuels that display the Auto logo. Makers’ Choice Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
Page 217 Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine.
Page 218 Maintenance and Specifications Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty.
Page 219 Maintenance and Specifications 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used.
Page 220 Maintenance and Specifications • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy. •...
Page 221 The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for...
Page 222 Maintenance and Specifications service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire.
Page 223 Maintenance and Specifications If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: •...
Page 224 Maintenance and Specifications 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level on the dipstick. It should be within the FULL HOT range. Do not add fluid if the level is within this range.
Page 225 3. If necessary, add brake fluid from a clean un-opened container until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specification ESA-M6C25–A. Refer to Lubricant specifications in this chapter.
Page 226 Maintenance and Specifications Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists. If taken internally, drink water and induce vomiting. Seek medical attention immediately. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes.
Page 227 Maintenance and Specifications the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage. Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 30 km [20 miles]).
Page 228 Maintenance and Specifications Correct fluid level The transmission fluid should be checked at normal operating temperature 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 30 km (20 miles) of driving. You can check the fluid without driving if the ambient temperature is above 10°C (50°F).
Page 229 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter.
Page 230 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 231 The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
Page 232 Maintenance and Specifications SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). •...
Page 233 If you do not follow these precautions, your vehicle may not drive properly and safely. Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford.
Page 234 Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, “Touring”, etc.), as originally offered by Ford. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over.
Page 235 Maintenance and Specifications • Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle. • If possible, avoid fully loading your vehicle. •...
Page 236: Refill Capacities
Maintenance and Specifications REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake fluid Motorcraft Fill to line on High reservoir Performance DOT 3 Motor Vehicle Brake Fluid Engine oil Motorcraft 3.8L OHV V6 4.7 L (5.0 (includes SAE 5W-20 engine...
Page 237 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fill hole. Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. Ensure the correct automatic transmission fluid is used.
Page 238: Lubricant Specifications
Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. LUBRICANT SPECIFICATIONS Item Ford part Ford part Ford name number specification Brake fluid...
Page 239 Maintenance and Specifications Item Ford part Ford part Ford name number specification Engine Motorcraft VC-4–A (US) ESE-M97B44 coolant Premium or CXC-10 Engine (Canada) Coolant (green- colored) Motorcraft VC-7–A WSS-M97B51 Premium –A1 Gold Engine Coolant (yellow- colored) Engine oil Motorcraft XO-5W20-QSP WSS-M2C153...
Page 240 C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118-A for complete refill of Traction-Lok axles. Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water. Ensure the correct automatic transmission fluid is used.
Page 241: Engine Data
Maintenance and Specifications ENGINE DATA Engine 3.8L OHV V6 4.6L SOHC V8 engine engine Cubic inches Required fuel 87 octane 87 octane Firing order 1-4-2-5-3-6 1-3-7-2-6-5-4-8 Spark plug gap 1.3-1.4 mm 1.3-1.4 mm (0.052-00.056 (0.052-00.056 inch) inch) Ignition system EDIS Coil on plug Compression ratio 9.4:1...
Page 242: Certification Label
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway MFD. BY FORD MOTOR CO. IN U.S.A. Traffic Safety DATE: XXXXX GVWR:XXXXXXXXXXXX FRONT GAWR: XXXXXX/XXXXXXX Administration REAR GAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL Regulations require MOTOR VEHICLE SAFETY, BUMPER, AND THEFT PRE- VENTION STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.
Page 243 Maintenance and Specifications Vehicle identification number The vehicle identification number is XXXXXXXXXXXXXXXXX attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the...
Page 244: Accessories
A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln, Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 245 Removable luggage rack Removable luggage rack adapters (Bike, ski, snowboard) Speed control Protection and appearance equipment All-weather vinyl floor mats Car cover Cargo liners, interior Carpet floor mats Door edge guards Door sill scuff plates, stainless Flat splash guards Front end covers (full and mini)
Page 246 • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment.
Page 247: Index
Index Auxiliary power point ......77 ABS (see Brakes) ... 137 Axle lubricant specifica- Air bag supplemental tions ....238, 241 restraint refill capacities ..236 system ....112–113 traction lok .... 141 and child safety seats ....... 114 description .... 113 disposal ....
Page 248 ....190 instrument panel .. 188 Customer interior ....189 Assistance ....155 plastic parts ..188 Ford accessories for washing ....185 your vehicle ..190 waxing ....185 Ford Extended wheels ....186 Service Plan ..176 wiper blades ..
Page 249 Index The Dispute service Settlement points ..... 195–196 Board ..... 177 starting after a Utilizing the collision ....157 Mediation/Arbitration Engine block Program ....181 heater ....... 134 Engine oil ....197 checking and adding ....197 Daytime running lamps dipstick ....
Page 250 Index fuel pump shut-off location ....151 switch ....157 GVWR (Gross Vehicle gauge ....... 16 Weight Rating) ..151 improving fuel calculating ..... 151 economy ....217 definition ....151 low fuel warning driving with a heavy light ......13 load ......
Page 251 Index lighting up panel and Lights, warning and interior ..... 66 indicator ....10 air bag ...... 11 anti-lock brakes (ABS) ....13, 138 Jack ......163 anti-theft ....11 positioning ..... 163 brake ......14 storage ....163 charging system ..11 Jump-starting your fuel cap light ...
Page 252 Index lubricant specifications ..241 reverse ....150 Radio ....19, 42–43 Mirrors Radio reception ... 60–61 side view mirrors (power) ....79 Rear window defroster ....64 Motorcraft parts ....217, 235 Relays ...... 158 Remote entry system ....90–91 illuminated entry ..
Page 253 Index Safety seats for tire grades ..... 231 children ....122 treadwear ....230 Seat belts (see Safety Towing ..... 153 restraints) ....101 recreational towing ....154 Seats ......98 child safety seats .. 122 trailer towing ..153 wrecker ....
Page 254 Index Windshield washer fluid and wipers Warning chimes ... 14–15 checking and adding fluid ......197 Warning lights (see Lights) ....... 10 checking and cleaning ....75 Washer fluid .... 197 operation ....75 Water, Driving replacing wiper through ....151 blades ......

Ford Car Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints

Driving

Roadside Emergencies

Customer Assistance

Cleaning

Maintenance and Specifications

Accessories

Index

Quick Links

Table of Contents

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Ford Car

Summary of Contents for Ford Car

Table of Contents