1. Manuals
  2. Brands
  3. DesignTech Manuals
  4. Remote Starter
  5. AutoCommand 20022
  6. Installation manual

DesignTech AutoCommand 20022 Installation Manual

“add-on” remote control car starter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
V 8.3
pcbv7.3/8.1
AutoCommand
"Add-On"
Remote Control Car Starter
Model 20022
Installation Manual
For use on automatic vehicles only.
For gasoline or diesel vehicles.
7955 Cameron Brown Court
Springfield, Virginia 22153 USA
www:designtech-intl.com
20022
®
Page 1

Advertisement

Table of Contents
loading

Related Manuals for DesignTech AutoCommand 20022

Summary of Contents for DesignTech AutoCommand 20022

  • Page 1 V 8.3 pcbv7.3/8.1 AutoCommand ® “Add-On” Remote Control Car Starter Model 20022 Installation Manual For use on automatic vehicles only. For gasoline or diesel vehicles. 7955 Cameron Brown Court Springfield, Virginia 22153 USA www:designtech-intl.com 20022 Page 1...

  • Page 2: Limited Warranty

    Should the car not start, or if it stalls after DesignTech International, Inc. will at its option either (1) replace this product with a function- starting, the AutoCommand® will make 2 further attempts to start it.

  • Page 3: User Information

    3 Tab connectors On/Off control switch Warning Label Window decal Ring terminal 7955 Cameron Brown Ct; Springfield, Virginia 22153 USA Hood pin switch set 2 cable ties (not pictured) Tel: (703)866-2000 or (800)337-4468 www:designtech-intl.com 20022 Page 3 Page 18 20022...
  • Page 4 1. Remove the top and bottom halves of the steering column shroud. AutoCommand Model 20022 2. Locate the small three wire harness (with White, Black and Yellow wires) running down from the ignition key cylinder on the top right hand side of the steering column into the instrument panel. 3.

  • Page 5: Installation Instructions

    Most of the 1990-1995 Cadillacs have a slight variation on the wiring for the VATS !! WARNING !! system. On these cars, there is an ORANGE wire (actually a vinyl sleeve) that contains smaller wires. This is located underneath the steering column next to the YELLOW On cars with airbags, you may notice bright yellow tubes or harnesses under- sleeve that is labeled “Air bag wiring”...

  • Page 6: Special Cases

    POWER & IGNITION WIRES C. You can choose the next option by pushing the left button again to index to the next option. When you get to the next option you want to change, simply repeat Step B above. After six seconds, The AutoCommand®...

  • Page 7: Setting Program Options

    4 Blue Wire (14 AWG) Ignition 1 #1 sets the starting method. The factory setting uses “No-Tach” start- ing. If you wish to use the tach to start, follow the instructions in 12A. #2 is for the choice of run times. Connect the LIGHT BLUE wire to the ignition 1 wire of your vehicle.
  • Page 8 Control Harness (All wires are the smaller 18 AWG size) 20. Trouble Shooting with the Self Diagnostics The AutoCommand® contains a built in diagnostic routine that will indicate why the unit turned off the car the last time that the unit was used. To activate 9.
  • Page 9 16. Brown Wire Acc. Pulse Control Harness 11. Initializing the AutoCommand® The optional BROWN wire is the Accessory Pulse output which gives out a 1 second EFORE THE CAR WILL START FOR THE FIRST TIME YOU MUST INITIALIZE THE transistor ground output just as the Accessory wire comes on. This is important in some vehicles to control the defroster or to control the GM R.A.P.

  • Page 10: Optional Steps

    12A. Tach Rate Learning OPTIONAL STEPS Note: Only use if the tachometer sensing method is chosen. Many of the optional steps require a relay to be hooked up. The most common relay used for this type of application is the Bosch type automotive relay P/N 0332 209150.

Table of Contents