Table of Contents Editorial Record Preface Chapter 1 Product Overview Features Available Models And Options 1.2.1 Options And Interfaces General Guide 1.3.1 IT-10 1.3.2 HA-C60IO (Basic Cradle) 1.3.3 HA-C61IO (Bridge Satellite Cradle) 1.3.4 HA-C32DCHG (Dual Battery Charger) 1.3.5 HA-C21BAT (Battery Pack) Chapter 2 Hardware Specifications IT-10...
Page 3
CASIO Computer Co., Ltd. in Tokyo Japan. Information in this document is subject to change without advance notice. CASIO Computer Co., Ltd. makes no representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose.
Preface The IT-10 is a new rugged PDA designed and built to be used for vertical applications (business specific applications) in severe business environment. The terminal is water-splash proof, dust proof and can withstand the inevitable rough handling that any vertical market device will suffer. This reference manual will explain you in detail about the specifications of hardware, reliability, environment, compliance and etc.
1. Product Overview 1.1 Features Hardware and software features at a glance • Uses Windows Mobile 2003 Second Edition Software for Pocket PC as the operating system. • Withstand a drop from 1 meter, and IP54 level for dust and water-splash resistance (compliant with IEC60529 standard).
1.3 General Guide 1.3.1 IT-10 External Views 12 13 Fig. 1.3 Refer to Table 1.4 for names of each part and its description. Fig. 1.2...
Page 10
Table 1.4 Names of parts Part Name Description Strap hole A commercially available strap can be attached here. Headphone jack A commercially available earphones or headphones (with 3.5 mm in diameter) can be attached here. Remove the rubber cover to use it. Reset switch This switch resets the terminal, similar to turning off and on the power switch.
1.3.2 HA-C60IO (Basic Cradle) Views Fig. 1.3 Fig. 1.4 Table 1.5 Names of parts Part Name Description Serial connector This connector mates with the serial connector on the bottom of the terminal. The power is also supplied to the terminal via this connector. Alignment pegs Align the terminal with these two pegs when mounting it to the Basic Cradle.
1.3.3 HA-C61IO (Bridge Satellite Cradle) Views Fig. 1.5 Fig. 1.6 Fig. 1.7 Refer to Table 1.6 for names of each part and its description.
Page 13
Table 1.6 Names of parts Part Name Description IrDA communication Align this port with the IrDA communication port of the terminal for data port transfer via the IrDA interface. Detection switch This switch detects when the terminal is correctly mounted on the Bridge Satellite Cradle.
1.3.4 HA-C32DCHG (Dual Battery Charger) View Fig. 1.8 Table 1.7 Names of parts Part Name Description Charging status Indicates the battery charge status. indicator lamp Green : Charging is complete. : Charging continues. Flashing red : Problem in the charge operation. Flashing green : Idle mode waiting for a next charge : No battery pack is mounted.
2. Hardware Specifications 2.1 IT-10 Table 2.1 Item Specification Remark CPU, Memory Intel PXA270 Processor (run at 416 MHz) Operating system Microsoft® Windows® Mobile 2003 Second Edition Software for Pocket PC 64 MB (M20) 128 MB (M30BR) FROM 64 MB (user area: approx. 20 MB) Display Display device 3.7-inch transflective TFT color LCD...
Page 17
Serial interface RS-232C Synchronization Start/stop, frame synchronization Baud rate 300, 600, 1200, 2400, 4800, 9600, 19.2K, 38.4K, 57.6K, 115.2K External output ±5V For communication level with PC only, not available for external output. USB Host Standard USB Ver. 1.1 compatible Baud rate 12 Mbps, 1.5 Mbps External output...
Page 18
Battery pack charge Approx. 5 hours or less Conditions; time - The surrounding temperature is at room temperature. - The dedicated AC adaptor or Cradle is used to charge the battery pack. Memory backup battery Approx. 4 hours (when the power is provided Conditions;...
Page 19
Pin layout for Serial Interface; 3 ・ ・ ・ ・ ・ ・ 24 25 26 Fig. 2.1 Signal layout; Table 2.2 Direction of Signal Remark signal flow CR CD2# #2 for detecting the Cradle RS232C CTS RS232C RS232C DCD RS232C RS232C DTR RS232C RS232C RTS...
Page 20
Table 2.3 Operating hours by model IEEE802.11b and Model Bluetooth Operating hour Operating condition and mode integrated - The surrounding temperature is at room temperature. - The battery pack (HA-C21BAT) is a brand new and IT-10M20 fully charged. - The backlight is turned off. Approx.
Page 22
Applicable to DC 12V±5% HA-C61IO. Input voltage Applicable to DC 5V±5% HA-C60IO. DC12V Approx. 3.5A Applicable to HA-C61IO. While supplying power to the terminal or transmitting data. Consumption current DC5V Approx. 3.0A Applicable to HA-C60IO. While supplying power Input from AC to the terminal or adaptor transmitting data.
2.3 DIP Switch Setting (For HA-C61IO) The DIP switch is located on the rear side of the Bridge Satellite Cradle (HA-C61IO). Change the ON/OFF settings according to your required system configuration. The new settings do not go into effect until the power switch is turned off and then back on again.
2.4 Status Indications With LEDs This chapter is not applicable to the HA-C60IO Basic Cradle. Various operational statuses on the HA-C61IO can be displayed using the LEDs. The following table describes LED indication modes and their meanings. Table 2.5 Item LED mode Description Remark...
2.5 HA-C32DCHG Table 2.6 Item Specification Remark Charge method Charge method Constant-voltage and constant-current With current limiter Approx. 2 hours (with one battery pack mounted) The surrounding temperature is at Charge period Approx. 4 hours (with two battery packs room temperature. mounted) Power Supplied via dedicated AC adaptor...
2.6 HA-C21BAT Table 2.8 Item Specification Remark Rated capacity 2,300 mAH Rated voltage 3.7V Charge period Approx. 2.0 hours When charging one battery pack at a time with HA-C32DCHG. Approx. 4.0 hours When charging two battery packs at a time with HA-C32DCHG Operating temperature Refer to the temperature for HA-C32DCHG...
3. Product Identification And Reference Numbers On the back of the terminal and its options (major options only), there is a bar code and numbers printed on label as shown in Fig. 3.1 below. This bar code is represented by 15 digits of Code128 and by alphanumeric characters beneath the bar code. The numbers from 1 to 9 in the figure represent identification and references of the terminal.
4. Quality References This chapter describes about quality references specially concerned with environmental performance, electric durability, mechanical durability, reliability, compliance and, etc. for the IT-10 series and its dedicated options. 4.1 Environmental Performances 4.1.1 IT-10 Table 4.1 Item Specification Condition...
4.1.2 HA-C60IO Table 4.2 Item Specification Condition Temperature Operation 0 to 40℃ Storage -20 to 60℃ Humidity Operation 10 to 85%RH No condensation Storage 10 to 90%RH Storage in carton box Temperature -20 to 60℃ Humidity 10 to 90%RH No condensation Dust and water-splash proof Not applicable.
4.1.4 HA-C32DCHG Table 4.4 Item Specification Condition Temperature Operation 0 to 40℃ Non-operation When battery pack is not charged. -20 to 60℃ Storage In carton box -20 to 60℃ Humidity Operation 10 to 85 %RH No condensation Storage 10 to 90 %RH No condensation In carton box 4.1.5 HA-C21BAT Table 4.5...
4.3 Physical Durability 4.3.1 IT-10 Table 4.10 Item Specification Condition Resistance to drop impact (height) In bare condition 100 cm Onto concrete, one time on each of the 6 sides and 4 corners. (no CF card fitted) In individual carton box 70 cm or less Onto concrete, one time on each of the 6 sides, 1 corner, 3 In master carton box 50 cm or less...
4.3.4 HA-C21BAT Table 4.13 Item Specification Condition Resistance to vibration 2.0 G or less 10 to 55 Hz In X,Y, and Z directions Reciprocally for 30 minutes Resistance to impact In bare condition 100 cm 6 faces, 4 edges onto P-tile. In individual carton box 70 cm or less 6 faces, 3 edges, 1 corner onto concrete floor.
4.4 Reliability 4.4.1 IT-10 Table 4.14 Item Specification Remark/Condition Service life Backlight 10,000 hours Half-life period 10 hours per day x 200 days per year x 5 years Reset switch 1,000 times Power switch 100,000 times Battery cover lock switch 3,000 times Other keys 250,000 times...
UL60950-1 FCC Part 15 sub Part 15B Class B part C + SAR IT-10M20 IT-10M30BR Note: Consult CASIO Computer Co., Ltd. for other areas. 4.5.2 HA-C60IO/HA-C61IO Table 4.19 Compliance Standard Europe EN55022:1998+A1:2000 Class B FCC Part 15B Class B EN55024:1998+A1:2001 Class B...
5. Cable Specifications 5.1 For Chain Connection And Short Length Length; 1 meter or less M a x m im u m View from side View from top 1 2 3 4 5 6 1 2 3 4 5 6 M odular plug C a b le ( s e e T a b le 5 .1 ) (c omppat ible with 6/ 6-...
5.2 For Chain Connection And Long Length Length; 1 meter or longer Max. 1,000m View from side View from top 1 2 3 4 5 6 1 2 3 4 5 6 Modular plug compatible Cable compatible with SK-UTP with 6/6-6 FR SYK50 by 100M3P by Sanyo Industrial Co.
6. Precautions 6.1 Handling Precautions Precautions for short-term storage (1 to 2 days) • If the IT-10 is to be stored over holidays (including Saturday and Sunday), replace the battery pack with brand-new one before starting the holiday. This will conserve the built-in memory backup battery and ensure retention of data on the terminal.
When charging the battery pack use only dedicated cradles or dedicated battery charger and its AC adaptor available from CASIO, at a temperature between 0°C and 40°C. If the battery pack is charged with battery chargers other than those specified by CASIO, it may be over-charged, or charged with an excessive current, or have abnormal chemical reactions induced, causing it to become hot, smoke, explode, or ignite.
If the IT-10 is continuously used in an abnormal condition, a fire or electric shock may occur. If there is an abnormality, immediately turn off the Power switch, and be sure to remove the batteries and then contact a CASIO distributor for repair. •...
Page 43
• Avoid exposing it to water and foreign matter Should foreign matter (metal chips, water, liquid chemicals) enter inside the product, immediately turn off the IT-10, remove the battery pack, and then contact your CASIO distributor. • Memory protection Contents of the IT-10 should always be backed up in personal computer to make a separate record from that on the terminal.