Advertisement
I I n n s s t t a a l l l l i i n n g g t t h h e e Z Z o o o o m m C C l l a a m m p p & & G G e e a a r r S S l l e e e e v v e e O O n n t t h h e e T T y y p p e e 1 1 L L e e n n s s e e s s
The Zoom Clamp has springs so it can be expanded to fit over
the Zoom Ring of the lens as shown in ( ( F F i i g g . . C C ) ) .
Install the Zoom Clamp with the extension tabs toward the rear
element of the lens. After installing the Zoom Clamp and Gear
Sleeve ( ( F F i i g g . . D D & & E E ) ) , install the Lens Port and rotate the Zoom
Ring on the lens. If the Zoom Ring and Gear Sleeve do not mesh
Type 1 Installation: Figure A
properly, install the rubber strips (supplied) to the inside
diameter of the Zoom Clamp as shown ( ( F F i i g g . . F F ) ) .
Two thicknesses of rubber strips are provided. Start by installing
the thinnest rubber strips. If the Zoom Clamp still is not tight
enough and meshes improperly with the Gear Sleeve, use the
thicker rubber strips. Reinstall the Zoom Clamp, Sleeve, and
Port. Mesh Gear Sleeve teeth with Black Housing Drive Gear
(Fig. G-Page #1 2)
I I n n s s t t a a l l l l i i n n g g t t h h e e Z Z o o o o m m C C l l a a m m p p & & G G e e a a r r S S l l e e e e v v e e O O n n T T y y p p e e 2 2 L L e e n n s s e e s s
Due to the larger diameter lens opening on Type 2 lenses, the
Type 2 Installation: Figure 1
Zoom Clamp and Gear Sleeve need to be installed from the rear
(bayonet end) of the lens. Use the housing Lens Release Control
and remove the camera lens from the camera body, after the
camera and lens have been installed in the housing.
Lens Zoom Ring
Zoom Clamp
Gear Sleeve
TOP OF HOUSING
M M a a n n u u a a l l F F o o c c u u s s i i n n g g N N o o t t e e : :
Ikelite DSLR housings are designed for auto-focus DSLR
cameras and lenses. Manual focusing is not recommended. If
you desire to manually focus a lens, the zoom clamp must be
moved onto the lens Manual Focus Ring and you must use the
housing zoom control knob to manually focus. This will result in
loss of zoom capability.
Type 1 lens
mounted
to camera
zoom
ring
Figure C
Figure A
9
Lens Manual
Focus Ring
Align
Zoom Clamp
grooved
tabs with
Gear Sleeve
ribs
Type 2 lens
11
Type 1 Installation: Figure B
T T y y p p e e 1 1 L L e e n n s s e e s s ( ( c c o o n n t t i i n n u u e e d d ) )
Type 1 Installation: Figure C
Figure D
Figure E
Figure C
N N O O T T E E : :
Before installing the lens port and checking operation, make sure
the teeth on the Gear Sleeve mesh with the teeth on the housing
Drive Gear ( ( F F i i g g . . G G ) ) . . When the port is installed, it will lock the
Gear Sleeve in place. After installing the port, rotate the housing
Zoom Control Knob to see that the Gear Sleeve is properly
rotating the lens Zoom ring.
Gear Sleeve
ribs
Align with
Zoom Clamp
grooved tabs
Figure B
apply
rubber strips
to inside of
clamp
Figure F
10
IKELITE
Black Housing
Figure G
12
Mesh
Gear Sleeve
teeth with
Drive Gear
Advertisement
