Table of Contents
Advertisement
Quick Links
E
Operator's
Extractor
Manual
Tools
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your ALTO
machine could result in injury to you or to other personnel; damage to the machine or to other property
could occur as well. You must have training in the operation of this machine before using it. If you
cannot read English, have this manual explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: ALTO U.S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 79042A
5/01
CLARKE TECHNOLOGY
Printed in the U.S.A.
Advertisement
Table of Contents
Related Manuals for Clarke Alto Extractor Tools
Summary of Contents for Clarke Alto Extractor Tools
- Page 1 All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: ALTO U.S. Inc., 2100 Highway 265, Springdale, Arkansas 72764. Form No. 79042A 5/01 CLARKE TECHNOLOGY Printed in the U.S.A.
-
Page 2: Table Of Contents
4" Plastic Hand Tool Assembly Drawing and Parts List ............ 8 4" Metal Hand Tool Assembly Drawing & Parts List ............9 8" Plastic Wand Assembly Drawing & Parts List ............... 10 12" Metal Wand Assembly Drawing & Parts List ............... 11 Page 2 CLARKE TECHNOLOGY Extractor Tools Operator's Manual... -
Page 3: Operator Safety Instructions
Keep all fasteners tight. Keep the adjustments according to specifications. WARNING: Make sure that all the labels, decals, warnings, cautions and instructions are fastened to the tool. Replace them when necessary by ordering them from Clarke Technology. ° WARNING: Do not use water that is hotter than 140... -
Page 4: Introduction
NOTE: Instructions for preparation and opera- tion of your extractor are given with the extractor. CAUTION: Clarke Technology will not be held liable for damage to the carpet, or poor results because of operator's lack of training. To operate the 4" hand tools, follow this procedure:... -
Page 5: How To Operate The 8" And 12" Floor Tool
How To Operate The 8" and 12" Wands NOTE: Instructions for preparation and op- eration of your extractor are given with the extractor. CAUTION: Clarke Technology will not be held liable for damage to the carpet, or poor results because of operator's lack of training. CAUTION: Do not use water that is hotter then 140°F. -
Page 6: How To Clean The Carpet
7. Make a pass halfway along the edge of the carpet. 8. As you make more passes, repeat one inch of the area already cleaned. 9. Make more passes until all of the room is cleaned. Page 6 CLARKE TECHNOLOGY Extractor Tools Operator's Manual... -
Page 7: Maintenance
CAUTION: To prevent damage to the spray jet, do not push a wire or any object through the opening in the jet. Use a dry cloth to wipe the tool. CLARKE TECHNOLOGY Extractor Tools Operator's Manual Page 7... -
Page 8: 4" Plastic Hand Tool Assembly Drawing And Parts List
CLARKE TECHNOLOGY 4" Plastic Hand Tool Tool Asm. 11/97 59231A 11 10 Ref # Part No. Description Qty. 55179A Plastic Head w/tube 1½" 59618A Vavle Assembly, Plastic 55181A VS Valve Hanger 1½" 85611A Screw, S.S. Pan Hd 10-32 x 1¼"... -
Page 9: 4" Metal Hand Tool Assembly Drawing & Parts List
CLARKE TECHNOLOGY 4" Metal Hand Tool Tool Asm. 11/97 59228A Ref # Part No. Description Qty. 55175A Head Assembly 59618A Valve Assembly, Plastic 54060A Tube Comp., MPT x " Ferrule 55181A VS Valve Hanger 1½ 85611A Screw, S.S. Pan Hd 10-32 x 1¼"... -
Page 10: 8" Plastic Wand Assembly Drawing & Parts List
Nut, S.S. Hex 10-32 30044Au Nozzle, ¼ (2 x 80°) 80082Au Washer, Plastic 80083Au Washer, Flat 9/16 SS 58901A Cable Tie, " Black 687501 Nipple, ¼ MPT x MPT Hex 737140 Quick Connector, FPT Male Page 10 CLARKE TECHNOLOGY Extractor Tools Operator's Manual... -
Page 11: 12" Metal Wand Assembly Drawing & Parts List
Vee Jet, ¼ MPT Brass 54507A Grip, Vinyl 6" x 1½" Dia. 54933A Handle Assembly 54934A Handle Back 962139 Bolt, S.S. ¼-20 x " 920208 Nut, S.S. Hex ¼-20 17u 30184A Strainer, Spray Jet CLARKE TECHNOLOGY Extractor Tools Operator's Manual Page 11... - Page 12 NOTES Page 12 CLARKE TECHNOLOGY Extractor Tools Operator's Manual...
- Page 13 +46 31 706 73 00 Customer Service Headquarters and Factory 2100 Highway 265 ALTO Norge A/S, Oslo (Norway) Springdale, Arkansas 72764 Bjornerudveien 24 (501) 750-1000 N-1266 +47 2275 1770 CLARKE TECHNOLOGY Extractor Tools Operator's Manual Page 13 Technical Service 1-800-356-7274...
- Page 14 (b). Return the product to the nearest Clarke Technology repair location. Transportation charges to and from the repair location must be prepaid by the purchaser. (c). Clarke Technology will repair the product and or replace any defective parts without charge within a reason- able time after receipt of the product.