Download  Print this page

Connecting The Terminals; Connecting The Antennas - Kenwood VR-606 VR-616 Instruction Manual

Kenwood audio video surround receiver instruction manual
Hide thumbs

Advertisement

Setting up the system

Connecting the terminals

1 Strip coating.
3 Insert the cord.
• Never short circuit the + and – speaker cords.
• If the left and right speakers are connected inversely or the speaker
cords are connected with reversed polarity, the sound will be
unnatural with ambiguous acoustic imaging. Be sure to connect the
speakers correctly.
Speaker impedance
After confirming the speaker impedance indications printed on the
rear panel of the receiver, connect speakers with matching impedance
ratings. Using speakers with a rated impedance other than that
indicated on the rear panel of the receiver could result in malfunctions
or damage to the speakers or receiver.
Speaker placement
Center speaker
Front
speaker
Surround
speaker
Front speakers : Place to the front left and right of the listening
position. Front speakers are required for all surround modes.
Center speaker : Place front and center. This speaker stabilizes the
sound image and helps recreate sound motion. Required for surround
playback.
Surround speakers : Place to the direct left and right, or slightly
behind, the listening position at even heights, approximately 1 meter
above the ears of the listeners. These speakers recreate sound
motion and atmosphere. Required for surround playback.
Subwoofer : Reproduces powerful deep bass sounds.
• Although the ideal surround system consists of all the speakers
listed above, if you don't have a center speaker or a subwoofer, you
can divide those signals between the available speakers in the
speaker settings steps to obtain the best possible surround
reproduction from the speakers you have available.
2 Push the lever.
4 Return the lever.
Subwoofer
Listening
position

Connecting the antennas

AM loop antenna
The supplied loop antenna is for use indoors. Place it as far as possible
from the receiver, TV set, speaker cords and power cord, and adjust
the direction for best reception.
AM antenna terminal connections
1 Push lever.
FM indoor antenna
The supplied indoor antenna is for temporary use only. For stable
signal reception we recommend using an outdoor antenna. Disconnect
the indoor antenna when you connect one outdoors.
FM antenna terminal connections
Insert cord.
FM outdoor antenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna into
the room and connect it to the FM 75Ω terminal.
GND
FM
AM
75Ω
ANTENNA
VIDEO
DVD
IN
MONITOR
OUT
L
VIDEO 2
IN
R
PHONO
CD / DVD
REC OUT PLAY IN
VIDEO 1
VIDEO 1
MD / TAPE
IN
OUT
Use an antenna
adaptor
(Commercially
available)
%
2 Insert cord.
S VIDEO
SYSTEM
DVD
CONTROL
MONITOR
DVD
VIDEO 2
OUT
IN
IN
CD / DVD
OPTICAL
VIDEO 2
COAXIAL
DIGITAL IN
FRONT
CENTER
SURROUND
SPEAKERS
SPEAKER
SPEAKERS
(8-16Ω)
(8-16Ω)
(8-16Ω)
AUDIO
DVD / 6CH INPUT
CENTER
+
+
-
-
SUB
REC OUT PLAY IN
PLAY IN
FRONT
SURROUND
WOOFER
VIDEO1
VIDEO 2
R
L
C
R
L
RED
WHITE
GREEN
GRAY
BLUE
SUB WOOFER
PRE OUT
SPEAKERS
Attach to the stand
GND
FM
AM
75Ω
ANTENNA
AM loop antenna
FM indoor antenna
FM outdoor antenna
3 Release lever.
AC OUTLETS
AC110V-120V / 220V-240V~
AC 220-
240V~
AC 110-
120V~
VOLTAGE
50 / 60Hz
SELECTOR
SWITCHED
TOTAL 90W MAX.
13
EN

Hide quick links:

Advertisement

Table of Contents
loading

  Also See for Kenwood VR-606 VR-616

  Related Manuals for Kenwood VR-606 VR-616

This manual is also suitable for:

Vr-616