Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for C&T Solution CT-XBT0x
Summary of Contents for C&T Solution CT-XBT0x
- Page 1 CT-XBT0x Intel® Atom™ E3800 Industrial Mini-ITX Motherboard User’s Manual Version 101 December 21, 2014 C&T Solution Inc. 17F-2, No. 700, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan Tel: +886-2-7731-7888 http://www.candtsolution.com...
-
Page 2: Preface
CT-XBT0x Mini-ITX Motherboard Preface Revision History Rev. Date Description 05/11/2014 Initial release 21/12/2014 Update BIOS chapter: LPSS & SCC Configuration, LCD Control Disclaimer All specifications and information in this User’s Manual are believed to be accurate and up to date. C&T Solution Inc. does not guarantee that the contents herein are complete, true, accurate or non-misleading. -
Page 3: Trademarks Acknowledgment
CT-XBT0x Mini-ITX Motherboard Trademarks Acknowledgment Intel® , Celeron® and Pentium® are trademarks of Intel Corporation. Windows® is registered trademark of Microsoft Corporation. AMI is trademark of American Megatrend Inc. IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International... -
Page 4: Safety Precautions
CT-XBT0x Mini-ITX Motherboard Safety Precautions Before installing and using the equipment, please read the following precautions: Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage. The power outlet shall be installed near the equipment and shall be easily accessible. -
Page 5: Table Of Contents
CT-XBT0x Mini-ITX Motherboard Table of Contents Preface ......................2 Revision History ....................2 Disclaimer ......................2 Copyright Notice ....................2 Trademarks Acknowledgment ................3 Environmental Protection Announcement ............3 Safety Precautions .................... 4 Introduction ..................... 8 Product Description ................8 Specifications .................. - Page 6 CT-XBT0x Mini-ITX Motherboard 2.4.9 Front Panel Audio Connector: Front_Audio .......... 20 2.4.10 GPIO Connector: GPIO ................ 20 2.4.11 I2C Pin Header: JP5 ................21 2.4.12 LAN LED "Link" Pin Header: JP6 ............21 2.4.13 LAN LED "Speed" Pin Header: JP7 ............21 2.4.14...
- Page 7 CT-XBT0x Mini-ITX Motherboard 5.1.4 Serial Port Console Redirection ............37 5.1.5 CPU Configuration ................38 5.1.6 SATA Configuration ................39 5.1.7 Miscellaneous Configuration ..............40 5.1.8 LPSS & SCC Configuration ..............41 5.1.9 CSM Configuration ................42 5.1.10 SDIO Configuration ................43 5.1.11...
-
Page 8: Introduction
CT-XBT0x Mini-ITX Motherboard 1. Introduction Product Description The CT-XBT0x is a single board computer in the Mini-IXT form factor featuring the Intel® Atom™ Processor E3800 Series in FCBGA1170 package on 22nm process technology in a single chip solution. The two 240-pin SODIMM sockets are for dual channel DDR3L 1333MHz memory with maximum capacity up to 8GB. -
Page 9: Specifications
CT-XBT0x Mini-ITX Motherboard Specifications Intel® Atom™ Processor E3800 Series and Intel® Celeron® Processor J1900/N2807 in FCBGA1170 package Atom™ E3845: 4-core, 1.91GHz, TDP 10W (CT-XBT01) Atom™ E3827: 2-core, 1.75GHz. TDP 8W (CT-XBT02) Atom™ E3815: 1-core, 1.46GHz, TDP 5W (CT-XBT03) ... - Page 10 CT-XBT0x Mini-ITX Motherboard Internal I/O 1x 2-ch 24-bit LVDS 2x SATA 3Gb/s ports 4x USB 2.0 ports (2 shared with Mini-PCIe) 1x RS-232/422/485 port (BIOS selectable, supports auto-flow) 5x RS-232 ports 1x 8-bit GPIO ...
-
Page 11: Available Models
CT-XBT0x Mini-ITX Motherboard Operating Temp. -20°C to 70°C Storage Temp. -40°C to 85°C Operating Humidity 10% to 90% relative humidity, non-condensing Certifications FCC Class A Available Models Model Processor Features Number Atom™... -
Page 12: Block Diagram
CT-XBT0x Mini-ITX Motherboard Block Diagram Channel A DDR3 1066/1333MHz 240pin DDR3/L DIMM DDI0 Channel B DDR3 DDI1 1066/1333MHz LVDS 240pin RTD2136 DDR3/L DIMM Intel® SDMMC Atom™ microSD E3800 Celeron® PCIe x1, Port 0 I210IT RJ-45 J1900/N2807 BIOS 2x SATA SATA x2 TPM1.2... -
Page 13: Mechanical Specifications
CT-XBT0x Mini-ITX Motherboard 2. Mechanical Specifications Dimensions Units: mm... -
Page 14: Board Layout
CT-XBT0x Mini-ITX Motherboard Board Layout UART SATA2/1_PWR SATA1 SATA2 DIMM_2 GPIO FAN2 FAN1 COM1 COM2 COM6 COM3 DIMM_1 COM4 COM5 USB_3 USB_2 USB_1 FRONT_ AUDIO 2.2.1 Connectors Connector Description CPU Power connector Battery socket Backlight Control connector microSD card slot... -
Page 15: Jumpers
CT-XBT0x Mini-ITX Motherboard Connector Description Front Panel pin header COM1 COM1 connectors (RS-232/422/485) COM2~6 COM2~6 connectors (RS-232) LPC connector DIMM_1 240-pin SODIMM socket DIMM_2 240-pin SODIMM socket FAN1 CPU fan connector FAN2 System fan connector FRONT_AUDIO Front Audio connector GPIO... -
Page 16: External Connectors
CT-XBT0x Mini-ITX Motherboard External Connectors DC-in USB 3.0 Display USB 2.0 LAN Line Port 2.3.1 DC Power In DC-Jack (Ø =2.5mm) for DC +12V power input 2.3.2 USB 3.0 Connector Signal Signal USB +5V USB_SSRX- USB_D- USB_SSRX+ USB_D+ GND_DRAIN USB_SSTX- USB_SSTX+ 2.3.3... -
Page 17: Vga Connector
CT-XBT0x Mini-ITX Motherboard 2.3.4 VGA Connector 15-pin D-sub Female Connector Signal Signal VGA_RED VGA_GRN VGA_BLU VGA_DDC_DAT VGA_HSYNC VGA_VSYNC VGA_DCC_CLK 2.3.5 USB 2.0 Connectors Signal USB +5V USB_D- USB_D+ 2.3.6 LAN Connector Signal Signal MDI0+ MDI2- MDI0- MDI1- MDI1+ MDI3+ MDI2+... -
Page 18: Internal Connectors
CT-XBT0x Mini-ITX Motherboard Internal Connectors 2.4.1 CPU Power Connector: ATX Connector Type: 2x2-pin ATX power connector Signal Signal +12V +12V 2.4.2 Backlight Control Connector: CN2 Connector Type: 1x8-pin pitch 2.0mm wafer connector Signal Signal Backlight Enable Backlight CTRL Backlight PWR... -
Page 19: Com1 Serial Port: Com1
CT-XBT0x Mini-ITX Motherboard 2.4.5 COM1 Serial Port: COM1 Connector Type: 2x5-pin pitch 2.0mm wafer connector RS-232 Signal Signal DCD, Data Carrier Detect DSR, Data Set Ready RXD, Receive Data RTS, Request To Send TXD, Transmit Data CTS, Clear To Send... -
Page 20: Lpc Connector: Dbg
CT-XBT0x Mini-ITX Motherboard 2.4.7 LPC Connector: DBG Connector Type: 2x5 pin pitch 1.27mm Signal Signal +3.3V LPC_AD3 LPC_AD2 RESET_DBG LPC_AD1 CLOCK_DEBUG LPC_AD0 LPC_FRAME 2.4.8 Fan Connectors: FAN1/2 FAN1: CPU Fan; FAN2: System Fan Signal +12V Fan Power Fan Sensor Fan PWM 2.4.9... -
Page 21: I2C Pin Header: Jp5
CT-XBT0x Mini-ITX Motherboard 2.4.11 I2C Pin Header: JP5 Connector Type: 1x3-pin pitch 2.54mm pin header connector Signal CLOCK DATA 2.4.12 LAN LED "Link" Pin Header: JP6 Connector Type: 1x2-pin pitch 2.54mm pin header connector Signal +3.3V LINK/ACTIVE 2.4.13 LAN LED "Speed" Pin Header: JP7 Connector Type: 1x2-pin pitch 2.54mm pin header connector... -
Page 22: Lvds Connector: Lvds
CT-XBT0x Mini-ITX Motherboard 2.4.14 LVDS Connector: LVDS Connector Type: 2x15pin pitch1.25mm LVDS connector Signal Signal LVDS_B3- LVDS_B3+ LVDS_B_CLK- LVDS_B_CLK+ LVDS_B2- LVDS_B2+ LVDS_B1- LVDS_B1+ LVDS_B0- LVDS_B0+ LVDS_I2C_DAT LVDS_I2C_CK LVDS_A3+ LVDS_A3- LVDS_A_CLK+ LVDS_A_CLK- LVDS_A2+ LVDS_A2- LVDS_A1+ LVDS_A1- LVDS_A0+ LVDS_A0- Panel PWR Panel PWR... -
Page 23: Mini-Pcie Connectors: Mini_Pcie1/2
CT-XBT0x Mini-ITX Motherboard 2.4.15 Mini-PCIe Connectors: MINI_PCIE1/2 Pin Signal Pin Signal Pin Signal WAKE# Reserved Reserved +3.3V Reserved USB_D+ Reserved Reserved PERST# Reserved PERn0 Reserved +1.5V +3.3Vaux LED_WWAN# CLKREQ# PERp0 Reserved UIM_PWR LED_WLAN# Reserved UIM_DATA +1.5V LED_WPAN# REFCLK- Reserved UIM_CLK SMB_CLK +1.5V... -
Page 24: Sata Power Connectors: Sata1_Pwr/ Sata2_Pwr
CT-XBT0x Mini-ITX Motherboard 2.4.17 SATA Power Connectors: SATA1_PWR/ SATA2_PWR Connector Type: 4-pin pitch 2.54mm connector Signal +12V 2.4.18 UART Serial IO Connector: UART Connector Type: 2x5-pin pitch 2.0mm wafer connector Signal Signal +3.3V UART1_RXD UART2_RXD UART1_TXD UART2_TXD UART1_RTS UART2_RTS UART1_CTS UART2_CTS 2.4.19 USB 2.0 Pin Header: USB_1... -
Page 25: Jumper Settings
CT-XBT0x Mini-ITX Motherboard Jumper Settings 2.5.1 Clear CMOS: JP2 Function Setting Jumper Normal (Default) 1-2 closed Clear CMOS 2-3 closed 2.5.2 Backlight Power: JP3 Function Setting Jumper +12V 1-2 closed +5V (Default) 2-3 closed 2.5.3 Panel Power: JP4 Function Setting Jumper +3.3V (Default) -
Page 26: Features & Interfaces
Integrated Display Engine, Processor Graphics and Integrated Memory Controller. BIOS AMI uEFI BIOS on 8MB SPI Flash ROM is used on the CT-XBT0x. System Memory The Integrated Memory Controller (IMC) of the processor supports single channel, non-ECC, unbuffered DDR3L-1333 memory up to 8GB with data transfer rates up to 1333MT/s. -
Page 27: Usb
CT-XBT0x Mini-ITX Motherboard The CT-XBT0x supports 1x USB 3.0 and 2x USB 2.0 external ports, and 4x internal USB 2.0 ports (2 shared with Mini-PCIe). Ethernet The CT-XBT0x features 1x 10/100/1000BASE-TX Ethernet by Intel 1210IT GbE Controller supporting WOL/PXE. SATA The CT-XBT0x supports 2x SATA 3Gb/s ports. -
Page 28: General Purpose Input Output
CT-XBT0x Mini-ITX Motherboard 3.10 General Purpose Input Output GPI and GPO pins may be implemented as GPIO. GPI and GPO pins may be implemented as SDIO. Signal Description General purpose output pins. Upon a hardware GPO[0:3] reset, these outputs should be low. - Page 29 CT-XBT0x Mini-ITX Motherboard Registers Description GPIO Input/Output Select GPIO8x Configuration Registers (Index port=0xA00, Data port=0xA01, Offset=0x88) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 GPO3 GPO2 GPO1 GPO0 GPI3 GPI2 GPI1 GPI0 Note.
-
Page 30: Watchdog Timer
CT-XBT0x Mini-ITX Motherboard 3.11 Watchdog Timer 3.11.1 Board Design The Watchdog Timer (WDT) is implemented by Fintek F81866AD-I. Register Address WDT Base Address 0xA10 3.11.2 Psuedo Code Set WDT Time Unit (Second Unit) Step1: ByteData = ReadIOByte(0xA15) //Read current setting Step2: ByteData = ByteData &... -
Page 31: Driver Installation
CT-XBT0x Mini-ITX Motherboard 4. Driver Installation The drivers for the CT-XBT0x can be found on the driver DVD included with the system. Install the following drivers in the order listed. 1. Chipset 2. Graphics 3. Audio 4. LAN 5. Intel Trusted Execution Engine (Intel TXE) 6. -
Page 32: System Bios
CT-XBT0x Mini-ITX Motherboard 5. System BIOS The system BIOS software is stored on EEPROM. The BIOS provides an interface to modify the configuration. When the battery is removed, all the parameters will be reset. Turn on the computer and press <DEL> or <F2> to enter the setup screens. -
Page 33: Advanced
CT-XBT0x Mini-ITX Motherboard Advanced... -
Page 34: Acpi Settings
CT-XBT0x Mini-ITX Motherboard 5.1.1 ACPI Settings Enable ACPI Auto Configuration: Enables or disables BIOS ACPI Auto Configuration. Enable Hibernation: Enable or Disable system ability to Hibernate. ACPI Sleep state: Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. Options: Suspend Disable, S3... -
Page 35: F81866 Super Io Configuration
CT-XBT0x Mini-ITX Motherboard 5.1.2 F81866 Super IO Configuration Enable/disable and configure the serial ports. 5.1.2.1 Serial Port 1 Configuration Device Type Select: Choose from RS-232, RS-422 and RS-485. -
Page 36: Hardware Monitor
CT-XBT0x Mini-ITX Motherboard 5.1.2.2 Serial Port 2~6 Configuration 5.1.3 Hardware Monitor... -
Page 37: Serial Port Console Redirection
CT-XBT0x Mini-ITX Motherboard 5.1.4 Serial Port Console Redirection Serial port console redirection settings. -
Page 38: Cpu Configuration
CT-XBT0x Mini-ITX Motherboard 5.1.5 CPU Configuration Intel Virtualization Technology: When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology Execute Disable Bit: XP can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SusE Linux 9.2, RedHat Enterprise 3 Update 3.) -
Page 39: Sata Configuration
CT-XBT0x Mini-ITX Motherboard 5.1.6 SATA Configuration The BIOS automatically detects the presence of SATA device and the hardware installed in the SATA ports will be showed in the configuration. Each port can be enabled or disabled individually. SATA Speed Support: Options: Gen 1, Gen 2. -
Page 40: Miscellaneous Configuration
CT-XBT0x Mini-ITX Motherboard 5.1.7 Miscellaneous Configuration OS Selection: Select the OS. -
Page 41: Lpss & Scc Configuration
CT-XBT0x Mini-ITX Motherboard 5.1.8 LPSS & SCC Configuration SCC SD Card Support: Options: Disable, Enable. LPSS I2C #2 Support: Options: Disable, Enable. LPSS HSUART Support: Options: Disable, Enable. -
Page 42: Csm Configuration
CT-XBT0x Mini-ITX Motherboard 5.1.9 CSM Configuration GateA20 Active: [Upon Request] – GA20 can be disabled using BIOS services. [Always] – do not allow disabling GA20; this option is useful when any RT code is executed above 1MB. Option ROM Message: Set display mode [Force BIOS] or [Keep Current] for Option ROM. -
Page 43: Sdio Configuration
CT-XBT0x Mini-ITX Motherboard 5.1.10 SDIO Configuration SDIO Access Mode: Auto Option: Access SD device in DMA mode if controller supports it, otherwise in PIO mode. DMA Option: Access SD device in DMA mode. PIO Option: Access SD device in PIO mode. -
Page 44: Usb Configuration
CT-XBT0x Mini-ITX Motherboard 5.1.11 USB Configuration Legacy USB Support: Auto option disables legacy support if no USB devices are connected. Disable option will keep USB devices available only for EFI applications. XHCI Hand-off: This is a workaround for OSes without XHCI hand-off support. -
Page 45: Security Configuration
CT-XBT0x Mini-ITX Motherboard 5.1.12 Security Configuration TXE EOP Message: Send EOP Message Before Enter OS. Intel® AT: Enable/Disable BIOS AT Code from Running. Intel® AT Platform PBA: Enable/Disable BIOS AT Code from Running. -
Page 46: Chipset
CT-XBT0x Mini-ITX Motherboard Chipset... -
Page 47: Northbridge Configuration
CT-XBT0x Mini-ITX Motherboard 5.2.1 Northbridge Configuration... - Page 48 CT-XBT0x Mini-ITX Motherboard 5.2.1.1 Intel IGD Configuration Integrated Graphics Device: Enable: Enable Integrated Graphics Device (IGD) when selected as the Primary Video Adaptor. Disable: Always disable IGD. IGD Turbo Enable: Enable/Disable: IGD Turbo. GFX Boost: Enable/Disable GFX Boost. PAVC: Enable/Disable Protected Audio Video Control.
- Page 49 CT-XBT0x Mini-ITX Motherboard 5.2.1.2 LCD Control Primary IGFX Boot Display: Default setting is “VBIOS Default”. “CRT”selects VGA, “EFP” selects DisplayPort, “LFP” selects LVDS. LCD Panel Type: Default setting is “1024x768 LVDS2”.
-
Page 50: Southbridge Configuration
CT-XBT0x Mini-ITX Motherboard 5.2.2 Southbridge Configuration High Precision Timer: Enable or Disable the High Precision Event Timer. Restore AC Power Loss: Select AC power state when power is re-applied after a power failure. - Page 51 CT-XBT0x Mini-ITX Motherboard 5.2.2.1 USB Configuration...
- Page 52 CT-XBT0x Mini-ITX Motherboard 5.2.2.2 PCI Express Configuration...
-
Page 53: Security
CT-XBT0x Mini-ITX Motherboard Security Administrator’s and User’s passwords could be set. If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. -
Page 54: Secure Boot Menu
CT-XBT0x Mini-ITX Motherboard 5.3.1 Secure Boot Menu Secure Boot: Secure Boot can be enabled if the System running in User mode with enrolled Platform Key (PK) and CSM function is disabled. Secure Boot Mode: Secure Boot mode selector. ‘Custom’ Mode enables... -
Page 55: Boot
CT-XBT0x Mini-ITX Motherboard Boot Setup Prompt Timeout: Number of seconds to wait for setup activation key. 65535 (0xFFFF) means indefinite waiting. Bootup NumLock State: Select [Enable] or [Disable] for the keyboard NumLock state. Quiet Boot: Enables or disables Quiet Boot option. -
Page 56: Save And Exit
CT-XBT0x Mini-ITX Motherboard Save and Exit... -
Page 57: Address Map
CT-XBT0x Mini-ITX Motherboard 6. Address Map I/O Port Address Map The assignments of the I/O port addresses for the CT-XBT0x under Windows® 7 Ultimate 64-bit are shown below. -
Page 58: Interrupt Controller (Irq) Map
CT-XBT0x Mini-ITX Motherboard I/O Port Address Map (cont'd) Interrupt Controller (IRQ) Map The interrupt controller map for the CT-XBT0x under Windows® 7 Ultimate 64-bit is shown below. - Page 59 CT-XBT0x Mini-ITX Motherboard Interrupt Controller (IRQ) Map (cont'd)
- Page 60 CT-XBT0x Mini-ITX Motherboard Interrupt Controller (IRQ) Map (cont'd)
- Page 61 CT-XBT0x Mini-ITX Motherboard Interrupt Controller (IRQ) Map (cont'd)
- Page 62 CT-XBT0x Mini-ITX Motherboard Interrupt Controller (IRQ) Map (cont'd)
- Page 63 CT-XBT0x Mini-ITX Motherboard Interrupt Controller (IRQ) Map (cont'd)
- Page 64 CT-XBT0x Mini-ITX Motherboard Interrupt Controller (IRQ) Map (cont'd)
-
Page 65: Memory Map
CT-XBT0x Mini-ITX Motherboard Memory Map The memory map of DRAM for the CT-XBT0x under Windows® 7 Ultimate 64-bit is shown below.