Antec VSK-1000 User Manual
Hide thumbs Also See for VSK-1000:

Advertisement

Quick Links

Инструкция
Antec VSK-1000
Перейти в карточку товара
8 800 775 98 98

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VSK-1000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Antec VSK-1000

  • Page 1 Инструкция Antec VSK-1000 Перейти в карточку товара 8 800 775 98 98...
  • Page 2 V S K - 1 0 0 0 NTUITIVE ESIGN WITH XCEPTIONAL ALUE S E R A N U A L...
  • Page 3 VSK-1000 is the best choice for nearly any value-conscious build. The VSK-1000 does not come with a power supply unit (PSU). Make sure you choose a power supply that is compatible with your computer components and has a long enough power harness to reach your motherboard and peripheral devices.
  • Page 4: Table Of Contents

    ABLE OF ONTENTS 1: I ECTION NTRODUCTION Case Specifications ........................4 Diagram ............................4 Included Screws ........................5 2: H ECTION ARDWARE INSTALLATION Setting Up ...........................7 Power Supply Installation ......................7 Motherboard Installation ......................8 Internal 3.5” Device Installation ....................8 External 5.25” Device Installation ..................9 External 3.5”...
  • Page 5: Section 1 Introduction

    ECTION NTRODUCTION...
  • Page 6: Diagram

    VSK-1000 U ’ ANUAL PECIFICATIONS Case Type Mid Tower Color Black Dimensions 18.9” (H) x 7.8” (W) x 18.8” (D) 475 mm (H) x 198 mm (W) x 490 mm (D) Weight 15.1 lbs / 6.9 kg Cooling 1 x top 140 mm TwoCool™ fan 1 x rear 120 mm TwoCool™...
  • Page 7: Included Screws

    NCLUDED CREWS A. Motherboard standoff (10; 6 preinstalled) B. Power supply / expansion slot screw (12) C. Hard drive / motherboard screw (21) D. Optical drive screw (12)
  • Page 8: Section 2 Hardware Installation

    ECTION ARDWARE NSTALLATION...
  • Page 9: Setting Up

    Note: Power supplies with fans on the bottom of the power supply will need to be mounted so that the fan is facing the top of the case. The VSK-1000 provides mounting holes for power supplies with standard mounting layouts to be installed upside up or upside down.
  • Page 10: Motherboard Installation

    3.5” D NTERNAL EVICE NSTALLATION The VSK-1000 provides space for up to six 3.5” hard drives. Insert your 3.5” device into the 3.5” drive cage from the rear of the cage until the mounting holes align with the screw holes in the cage.
  • Page 11: External 5.25" Device Installation

    5.25” D XTERNAL EVICE NSTALLATION There are three externally accessible 5.25” drive bays. To access these bays, you must first remove the front bezel and drive bay cover: 1. Press on the three tabs pictured to the left to release the front bezel.
  • Page 12: Cable Management

    3. Lay the VSK-1000 on its side, and hold the drive in place on top of the grommets. 4. Secure the device to the case with the screws provided, tightening the screws with your fingers first, and then the screwdriver.
  • Page 13: Section 3 Front I/Oports

    ECTION RONT ORTS...
  • Page 14: Usb 2.0

    USB 2.0 Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the motherboard user’s manual to ensure that it matches the table below: Signal Names Signal Names USB Power 1 USB Power 2 Negative Signal 1 Negative Signal 2 Positive Signal 1...
  • Page 15: Power Switch / Hard Disk Drive Led Connectors

    LED C OWER WITCH RIVE ONNECTORS Connected to your front panel are LED and switch leads for power and HDD LED activity. Attach these to the corresponding connectors on your motherboard. Consult your motherboard manual for specific pin header locations. For LEDs, colored wires are positive ( + ). White or black wires are negative ( –...
  • Page 16: Included Fans

    High if you choose to connect the fan(s) to a fan control device or to the Fan-Only connector found on some Antec power supplies. A fan control device regulates the fan speed by varying the voltage, which may start as low as 4.5V to 5V. Connecting a TwoCool™ fan set on Low to a fan-control device may result in the fan not being able to start because the already lowered voltage from the fan control device will be further reduced by the TwoCool™...
  • Page 17: Optional Front Intake Fans

    PTIONAL There are two optional 120 mm front intake fan mounts at the front of the HDD cage. We recommend using Antec 120 mm speed control fans and setting the speed to Low. These fans must be installed so that the air is blowing into the case.
  • Page 18 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2011 Antec, Inc. All rights reserved. All trademarks are the property of their respective owners. Reproduction in whole or in part without written permission is prohibited.
  • Page 19 Antec VSK-1000 Описание Характеристики...

Table of Contents