Panasonic NV-GS120EB Operating Instructions Manual page 5

Recording Mode
pThe [t] Indication flashes and then is
displayed.
pThe entire screen becomes brighter.
t
To Resume Normal Recording
Press the [BACK LIGHT] Button.
pFor other notes concerning this item, see
-58-
Night View Functions
Colour Night View Function
This function allows you to record colour images
brightly in a dark place without using the Video
Flash.
1
Press the [COLOUR NIGHT VIEW] Button
(11) until the [C.NIGHT VIEW] Indication
appears.
(11)
COLOUR
NIGHT
VIEW
C.NIGHT
VIEW
0 Lux Night View Function
Using the LCD Monitor light, a dark scene of
almost 0 lux can be recorded.
1
Press the [COLOUR NIGHT VIEW] Button
(11) until the [0LUX NIGHT VIEW] Indication
appears.
C.NIGHT 0LUX
VIEW NIGHT VIEW
pThe [REVERSE THE LCD MONITOR]
Indication appears.
2
Rotate the LCD Monitor frontward (to the
lens side).
pThe screen becomes white and the
Viewfinder turns on.
pThe available range of the LCD Monitor light
is within approximately 1.2 metre.
To Cancel the Night View Functions
Press the [COLOUR NIGHT VIEW] Button
repeatedly until neither the [C.NIGHT VIEW]
Indication nor the [0LUX NIGHT VIEW] Indication
appears.
pFor other notes concerning this item, see
.
Soft Skin Function
This enables you to record skin colours in a softer
tone. In order to get the best result, avoid
background colours similar to the skin colour of
the subject. Otherwise, this may result in a softer
background lacking in detail.
1
Press the [SOFT SKIN] Button (12)
(12)
SOFT
SKIN
pThe [
] Indication appears.
SOFT SKIN
SOFT SKIN
pTo obtain the best effect, we recommend to
take the bust shot, so that the upper part from
the breast of the subject can be framed in the
screen.
To Cancel the Soft Skin Function
Press the [SOFT SKIN] Button.
Wind Noise Reduction Function
This function reduces the sound of wind hitting
the microphone when recording.
1
Set [TAPE RECORDING MENU] or
[CARD RECORDING MENU] >>
[RECORDING] >> [WIND CUT] >> [ON].
STILL
ENTER
s i
FADE
(14)
MENU
pThe [WIND CUT] Indication appears.
WIND CUT
-28-
(88) Clip
pInsert the plug securely into the [REMOTE]
Socket as far as it will goes. A loose
connection will spoil normal operation.
The Remote Controller
x Inserting a Button-type Battery
Before using the Remote Controller, insert the
supplied button-type battery.
1
While pressing the Stopper
.
-58-
Battery Holder.
2
Insert the button-type battery with the (K)
marking facing upward.
.
3
Insert the Battery Holder into the Remote
Controller.
pWhen the button-type battery is exhausted,
replace it with a new CR2025 battery. (A battery
is normally expected to last about 1 year.
However, it depends on operation frequency.)
pMake sure to match the poles correctly when
inserting the battery.
WARNING
"THE LITHIUM BATTERY IS A CRITICAL
COMPONENT (TYPE NUMBER CR2025
MANUFACTURED BY PANASONIC).
IT MUST NEVER BE SUBJECTED TO
EXCESSIVE HEAT OR DISCHARGE. IT
MUST THEREFORE ONLY BE FITTED IN
EQUIPMENT DESIGNED SPECIFICALLY
FOR ITS USE.
REPLACEMENT BATTERIES MUST BE OF
THE SAME TYPE AND MANUFACTURER.
THEY MUST BE FITTED IN THE SAME
MANNER AND LOCATION AS THE
ORIGINAL BATTERY, WITH THE
CORRECT POLARITY CONNECTIONS
OBSERVED.
DO NOT ATTEMPT TO RE-CHARGE THE
OLD BATTERY OR RE-USE IT FOR ANY
OTHER PURPOSE. IT SHOULD BE
DISPOSED OF IN WASTE PRODUCTS
DESTINED FOR BURIAL RATHER THAN
INCINERATION."
Before Use
x Using the Remote Controller
1
Direct the Remote Controller at the Remote
Control Sensor
and press an appropriate button.
, pull out the
pDistance from the Movie Camera: Within
1 approximately 5 metres
pAngle: Within approximately 10Q in the
upward, and 15Q in the downward and
horizontal directions from the central axis
pThe above operating ranges are for indoor use.
Outdoors or under strong light, the Movie
Camera may not operate properly even within
the above ranges.
pWithin a 1-metre range, you can also use the
Remote Controller on the LCD Monitor side of
the Movie Camera.
Selecting Remote Controller Modes
When 2 Movie Cameras are used
simultaneously, they can be operated individually
by selecting different Remote Controller Modes.
pIf the Remote Controller Mode of the Movie
Camera and that of the Remote Controller do
not match, [REMOTE] Indication is displayed.
Setup on the Movie Camera:
Set [REMOTE] on the [INITIAL] Sub-Menu to the
desired Remote Controller Mode. (
Setup on the Remote Controller:
[VCR1]:
Press the [&] Button and [w] Button
simultaneously.
[VCR2]:
Press the ['] Button and [w] Button
simultaneously.
pWhen the battery in the Remote Controller is
replaced, the mode is automatically reset to
[VCR1] Mode.
-9-
(29) of the Movie Camera
10˚
(29)
15˚
15˚
15˚
)
-17-
STILL ADV PAUSE STILL ADV
' &
INDEX STOP INDEX P.B. ZOOM
w
SELECT