Download
Share
Print this page
  1. Manuals
  2. Brands
  3. LightwaveRF Manuals
  4. Dimmer
  5. JSJS LW250
  6. Operation manual

LightwaveRF JSJS LW250 Operation Manual

1 gang 1 way dimmer 250w
Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
LightwaveRF
connect
1 Gang 1 Way Dimmer 250w
Operation Manual
Model No: JSJS LW250
It is important to install this product in accordance
with the tting instructions below. Failure to do so
may render your guarantee void.
IMPORTANT: PLEASE RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE AND FOR GUIDANCE ON
THE ASSOCIATION OF REMOTE HANDSETS. FOR
HELP AND SETUP GUIDANCE PLEASE VISIT
www.lightwaverf.com
OVERVIEW:
Blue LED 'ON'
Amber LED 'OFF'

Advertisement

loading

Related Manuals for LightwaveRF JSJS LW250

Summary of Contents for LightwaveRF JSJS LW250

  • Page 1 LightwaveRF connect 1 Gang 1 Way Dimmer 250w Operation Manual Model No: JSJS LW250 It is important to install this product in accordance with the tting instructions below. Failure to do so may render your guarantee void. IMPORTANT: PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE AND FOR GUIDANCE ON THE ASSOCIATION OF REMOTE HANDSETS.
  • Page 2 FITTING AND WIRING INSTRUCTIONS: Important Things to Consider Before you Begin 1). Before commencing work, ALWAYS isolate the mains power supply and remove the fuse in the fuse box or switch o the circuit breaker in the consumer unit. 2). If unit is to be used as a replacement for an existing product, remove existing unit from its location and disconnect the wiring.

  • Page 3: Installation Guide

    (min 40W, max 250W) • Dimmable Electronic Low Voltage Transformers • GU10 and equivalent HI spot mains halogen bulbs The 1 gang LightwaveRF Slave Dimmer is NOT compatible with: • Wire-wound transformers (generally older models) • Electric Motors Please Note: •...
  • Page 5 5. Strip the cable as shown then connect the wiring as per the diagrams below, ensure terminals are properly tightened and no bare wire is visible. Max: 8mm Min: 13mm Additional slave units (maximum of 6 in line) will allow for 2-way / multi-way operation (units can only be operated manually).
  • Page 6 Multi-Way 6. Screw the dimmer switch to the mounting box and ensure that the screws are su ciently tight to support the product, but please do not over tighten as this may cause some damage. Ensure that the plastic spacer is correctly aligned and that no wires are trapped between the dimmer switch and the back of the wall box.

  • Page 7: Operation

    7. Replace the plate – a ‘click’ sound should be heard to signify that the plate has been correctly replaced. OPERATION: Please Note: • At least one master unit must be installed in order for slave unit to operate. • The LED indicators on master unit and slave unit ash simultaneously.
  • Page 8 Dimming Control on the Receiver Lowering Dim Level 1. Make sure the light is switched on. 2. Hold down the ‘OFF’ button. 3. After 1 sec. the light will start to dim down. 4. At the desired brightness level release the ‘OFF’ button.
  • Page 9 SPECIFICATION (per module): Input rating: 220-240V~ 50Hz. Output rating: 40~250W Max. Incandescent lamp, 200VA Max. Low voltage lighting electronic transformers. Manual ON/OFF with dimmer function. Birmingham Science Park Aston Faraday Wharf Holt Street Birmingham B7 4BB Tel: 01902 500 562 Email: support@jsjsdesigns.com...