SRP-350/352plusIII ■ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet.
Page 3
SRP-350/352plusIII CAUTION Violating following instructions can cause slight wound or damage the appliance. Keep the desiccant out of children’s reach. If you observe a strange smoke, odor or noise from the printer, unplug it before taking following • If not, they may eat it.
Page 4
SRP-350/352plusIII ■ Warning - U.S.A Class A Digital Device : Wired Device This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
SRP-350/352plusIII ■ Caution Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or remove the cables on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF”.
Page 6
- The following Bluetooth mark and QD ID B021701 is only applicable to models with the Bluetooth SIG qualification. We at Bixolon Co., Ltd. constantly strive to improve product functions and quality. To do this, the specifications of our product and the contents of the manual may change without prior notice.
SRP-350/352plusIII 1. Installing Printer and Getting Started 1-1 Unpacking Check the following contents list, and contact your dealer for assistance if any item is missing or incorrect. SRP-350/352plusIII Cable Cover Paper Installation Guide AC/DC Adapter Power Cord - 8 -...
* IP and MAC information can be obtained from the self-test. Refer to the Ethernet User’s Manual that is available from the BIXOLON website for more detailed information. * For using this interface in the Bluetooth or WLAN applied product, Printer wiring requires to use double shielded (Cat 7) Ethernet cable.
SRP-350/352plusIII 1-2-3 Serial Interface(RS-232C) 1-2-3-1 Single Interface USB Connector Serial Cable Connector Ethernet Connector Power Connector 1-2-3-2 Dual Interface USB Connector Ethernet Connector Serial Cable Connector Power Connector - 10 - Rev. 1.02...
Page 11
SRP-350/352plusIII Pin No. Signal Name Direction Function Main Frame GND Frame Ground Output Data Transmission Input Data Reception This signal shows whether the host computer can receive data (hardware flow control). 1) MARK (Logic 1): The host computer can receive data.
SRP-350/352plusIII 1-2-5 Wireless LAN Interface 1) Wireless LAN Communication Specifications Item Specifications Frequency 2.412~2.484 GHz Channel Channel 1~13 Protocol 802.11b, 802.11g, 802.11n 2) Connecting Wireless LAN Printer can be connected to terminal devices with wireless LAN communication capability (PDA, PC, smartphone, tablet PC, etc.).
SRP-350/352plusIII 1-3 Drawer Cable Connect the cash drawer connecting cable to the cash drawer connector located in the back of the printer. ※ WARNING Use a cash drawer that meets the printer specifications. Using an improper cash drawer may cause faults in the cash drawer and the printer.
SRP-350/352plusIII 1-4 Setting Dip Switches 1-4-1 Serial Interface • DIP Switch 1 Function Default Auto Line Feed Enabled Disabled Flow Control XON/XOFF DTR/DSR Data Length 7-bit 8-bit Parity Check Parity Selection EVEN Baud Rate Selection Refer to the following Table 1 (bps) •...
SRP-350/352plusIII 1-4-3 Bluetooth Interface • DIP Switch 1 Function Default Auto Line Feed Enabled Disabled Reserved Reserved Reserved Bluetooth mode Normal Reserved Reserved Reserved • DIP Switch 2 Function Default Reserved Reserved Internal Bell Control Disabled Enabled Auto Cutter Selection...
SRP-350/352plusIII 1-5 Installing & Replacing Paper ※ CAUTIONS Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer may not detect the paper end correctly.
Page 18
SRP-350/352plusIII 1-5-5 Check the orientation of the roll paper when inserting it into the printer. 1-5-6 Pull out a small amount of paper as shown in the picture, and close the cover. ※ CAUTIONS When closing the cover, hold down the center of printer cover firmly so that paper roll is loaded correctly.
SRP-350/352plusIII 1-6 Recommended Papers - TF50KS-E (Paper Thickness: 65μm): Nippon Paper Industries Co., Ltd. - PD 160R (Paper Thickness: 75μm): New Oji Paper Mfg. Co., Ltd. - P350 (Paper Thickness: 62μm): Kansaki Specialty Paper, Inc. (USA) ※ CAUTIONS Use of papers other than those recommended above may damage TPH or degrade the printing quality and our company is not responsible for the damage caused by non- recommended papers.
SRP-350/352plusIII 1-8 Removing Paper Jam 1-8-1 When a paper jam occurs, turn the printer off and then back on, open the cover, and remove the jammed paper. ※ In case of a minor jam, it may be possible that the operating blade returns to the original position and cover can be opened simply by turning the printer off and then back on.
1-9 Adjusting Paper Near-end Sensor Setting SRP-350/352plusIII Series printer has built-in near-end sensors that provides an alarm signal when the paper has run almost to the end. SRP-350/352plusIII Series can be configured as wall mounted or desktop operation and the settings of the paper near-end sensor should be adjusted accordingly.
SRP-350/352plusIII 1-11 Connecting a Computer Use the cable that comes with the printer to connect the printer to computers. 1-11-1 Plug the cable connector securely into the printer’s interface connector located in the back of the printer. 1-11-2 Tighten the screws on the cable connector.
SRP-350/352plusIII 2. Self-Test The self-test checks whether the printer has any problems. If the printer does not function properly, contact your dealer. The self-test procedure is as follows: 2-1 Make sure paper roll has been installed properly. 2-2 Turn on the power while holding down the FEED button and the self-test begins.
SRP-350/352plusIII 3. Hexadecimal Dumping This function allows experienced users to see exactly what data is coming to the printer. This can be useful in finding software problems. When you turn on the hexadecimal dump function, the printer prints all commands and data in hexadecimal format along with a guide section to help you find specific commands.
SRP-350/352plusIII 5. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality. In this case clean the printer as follows: 5-1-1 Open the printer cover and remove any paper. 5-1-2 Clean the print head with a cotton swab moistened with alcohol solvent.